In this chapter, we will restrict our attention to the ferrites and a few other closely related materials. The great interest in ferrites stems from their unique combination of a spontaneous magnetization and a high electrical resistivity. The observed magnetization results from the difference in the magnetizations of two non-equivalent sub-lattices of the magnetic ions in the crystal structure. Materials of this type should strictly be designated as “ferrimagnetic” and in some respects are more closely related to anti-ferromagnetic substances than they are to ferromagnetics in which the magnetization results from the parallel alignment of all the magnetic moments present. We shall not adhere to this special nomenclature except to emphasize effects, which are due to the existence of the sub-lattices.

Ferromagnetic materials

Nanodevices don't use much energy, and if the little they do need can be scavenged from vibrations associated with foot steps, heart beats, noises and air flow, a whole range of applications in personal electronics, sensing and defence technologies opens up. Energy gathering of that type requires a technology that works at low frequency range (below 10 Hz), ideally based on soft, flexible materials. A group working at Georgia Institute of Technology has now come up with a system that converts low-frequency vibration/friction energy into electricity using piezoelectric zinc oxide nanowires grown radially around textile fibres. By entangling two fibres and brushing their associated nanowires together, mechanical energy is converted into electricity via a coupled piezoelectric-semiconductor process. This work shows a potential method for creating fabrics which scavenge energy from light winds and body movement. A self-powering nanosystem that harvests its operating energy from the environment is an attractive proposition for sensing, personal electronics and defence technologies1. This is in principle feasible for nanodevices owing to their extremely low power consumption2,3,4,5. Solar, thermal and mechanical (wind, friction, body movement) energies are common and may be scavenged from the environment, but the type of energy source to be chosen has to be decided on the basis of specific applications. Military sensing/surveillance node placement, for example, may involve difficult-to-reach locations, may need to be hidden, and may be in environments that are dusty, rainy, dark and/or in deep forest. In a moving vehicle or aeroplane, harvesting energy from a rotating tyre or wind blowing on the body is a possible choice to power wireless devices implanted in the surface of the vehicle. Nanowire nanogenerators built on hard substrates were demonstrated for harvesting local mechanical energy produced by high-frequency ultrasonic waves6,7. To harvest the energy from vibration or disturbance originating from footsteps, heartbeats, ambient noise and air flow, it is important to explore innovative technologies that work at low frequencies (such as <10 Hz) and that are based on flexible soft materials. Here we present a simple, low-cost approach that converts low-frequency vibration/friction energy into electricity using piezoelectric zinc oxide nanowires grown radially around textile fibres. By entangling two fibres and brushing the nanowires rooted on them with respect to each other, mechanical energy is converted into electricity owing to a coupled piezoelectric–semiconductor process8,9. This work establishes a methodology for scavenging light-wind energy and body-movement energy using fabrics.

http://www.nanoscience.gatech.edu/zlwang/paper/2008/08_nat_1.pdf

Microfibre–nanowire hybrid structure for energy scavenging

We report a size dependence of Young's modulus in [0001] oriented ZnO nanowires (NWs) with diameters ranging from 17 to 550 nm for the first time. The measured modulus for NWs with diameters smaller than about 120 nm is increasing dramatically with the decreasing diameters, and is significantly higher than that of the larger ones whose modulus tends to that of bulk ZnO. A core-shell composite NW model in terms of the surface stiffening effect correlated with significant bond length contractions occurred near the {1010} free surfaces (which extend several layers deep into the bulk and fade off slowly) is proposed to explore the origin of the size dependence, and present experimental result is well explained. Furthermore, it is possible to estimate the size-related elastic properties of GaN nanotubes and relative nanostructures by using this model.

Size dependence of Young's modulus in ZnO nanowires.

I. Introduction A FUNCTIONAL relationship between cell growth and the initiation and progression of events associated with differentiation has been a fundamental question challenging developmental biologists for more than a century. In the case of bone, as observed with other cells and tissue, the relationship of growth and differentiation must be maintained and stringently regulated, both during development and throughout the life of the organism, to support tissue remodeling. For many years, bone was defined anatomically and examined largely in a descriptive manner by ultrastructural analysis and by biochemical and histochemical methods. These studies provided the basis for our understanding of bone tissue organization and orchestration of the progressive recruitment, proliferation, and differentiation of the various cellular components of bone tissue. Now, complemented by an increased knowledge of molecular mechanisms that are associated with and regulate expression of genes encoding phenotypic compone...

Molecular mechanism mediating proliferation, defferentiation interralationships during progressie development of the osteoblast phenotype

Giant and isotropic magnetoresistance as huge as −53% was observed in magnetic manganese oxide La0.72Ca0.25MnOz films with an intrinsic antiferromagnetic spin structure. We ascribe this magnetoresistance to spin‐dependent electron scattering due to spin canting of the manganese oxide.

31p-S-4 Giant Magnetoresistance in Magnetic Manganese Oxide with Intrinsic Antiferromagnetic Spin Structure

Barium ferrite films with high coercivity (>2000 Oe) have been prepared on single crystal sapphire substrates by laser in-situ deposition. The structures of these films were characterized by x-ray diffractometry. X-ray diffraction pattern shows a preferential c-axis orientation normal to the film plane at a high deposition temperature and a random orientation at a lower deposition temperature. The magnetic properties of the films were analysed by a Vibrating Sample Magnetometer (VSM) and surface morphology was analysed by an Atomic Force Microscope (AFM).

Xianting Zeng

Papers

Pulsed Laser Deposition of High Coercivity Barium Ferrite Films