Freedom of design, mass customisation, waste minimisation and the ability to manufacture complex structures, as well as fast prototyping, are the main benefits of additive manufacturing (AM) or 3D printing. A comprehensive review of the main 3D printing methods, materials and their development in trending applications was carried out. In particular, the revolutionary applications of AM in biomedical, aerospace, buildings and protective structures were discussed. The current state of materials development, including metal alloys, polymer composites, ceramics and concrete, was presented. In addition, this paper discussed the main processing challenges with void formation, anisotropic behaviour, the limitation of computer design and layer-by-layer appearance. Overall, this paper gives an overview of 3D printing, including a survey on its benefits and drawbacks as a benchmark for future research and development.

Additive manufacturing (3D printing): A review of materials, methods, applications and challenges

介绍了Kirk—Othmer Encyclopedia of Chemical Technology（化工技术百科全书）（第五版）电子图书网络版数据库，并对该数据库使用方法和检索途径作出了说明，且结合实例简单地介绍了该数据库的检索方法。

Kirk-Othmer Encyclopedia of Chemical Technology数据库介绍及实例

Polylactic acid (PLA) controlled delivery carriers for biomedical applications.

Highly open porous biodegradable poly(L-lactic acid) ¿PLLA scaffolds for tissue regeneration were fabricated by using ammonium bicarbonate as an efficient gas foaming agent as well as a particulate porogen salt. A binary mixture of PLLA-solvent gel containing dispersed ammonium bicarbonate salt particles, which became a paste state, was cast in a mold and subsequently immersed in a hot water solution to permit the evolution of ammonia and carbon dioxide within the solidifying polymer matrix. This resulted in the expansion of pores within the polymer matrix to a great extent, leading to well interconnected macroporous scaffolds having mean pore diameters of around 300-400 microm, ideal for high-density cell seeding. Rat hepatocytes seeded into the scaffolds exhibited about 95% seeding efficiency and up to 40% viability at 1 day after the seeding. The novelty of this new method is that the PLLA paste containing ammonium bicarbonate salt particles can be easily handled and molded into any shape, allowing for fabricating a wide range of temporal tissue scaffolds requiring a specific shape and geometry.

A Novel Fabrication Method of Macroporous Biodegradable Polymer Scaffolds Using Gas Foaming Salt as Porogen Additive

Synthesis of hydroxyapatite for biomedical applications

In the present work polylactide (PLA)/15wt% hydroxyapatite (HA) porous scaffolds with pre-modeled structure were obtained by 3D-printing by fused filament fabrication. Composite filament was obtained by extrusion. Mechanical properties, structural characteristics and shape memory effect (SME) were studied. Direct heating was used for activation of SME. The average pore size and porosity of the scaffolds were 700μm and 30vol%, respectively. Dispersed particles of HA acted as nucleation centers during the ordering of PLA molecular chains and formed an additional rigid fixed phase that reduced molecular mobility, which led to a shift of the onset of recovery stress growth from 53 to 57°C. A more rapid development of stresses was observed for PLA/HA composites with the maximum recovery stress of 3.0MPa at 70°C. Ceramic particles inhibited the growth of cracks during compression-heating-compression cycles when porous PLA/HA 3D-scaffolds recovered their initial shape. Shape recovery at the last cycle was about 96%. SME during heating may have resulted in "self-healing" of scaffold by narrowing the cracks. PLA/HA 3D-scaffolds were found to withstand up to three compression-heating-compression cycles without delamination. It was shown that PLA/15%HA porous scaffolds obtained by 3D-printing with shape recovery of 98% may be used as self-fitting implant for small bone defect replacement owing to SME.

Y.Z. Estrin

Papers

Mechanical properties and shape memory effect of 3D-printed PLA-based porous scaffolds.