Geotechnical and Geological Engineering 

About: Geotechnical and Geological Engineering is an academic journal published by Springer Science+Business Media. The journal publishes majorly in the area(s): Geology & Rock mass classification. It has an ISSN identifier of 0960-3182. Over the lifetime, 3770 publications have been published receiving 48898 citations. The journal is also known as: Geotechnical & geological engineering.

The geomechanics of CO2 storage in deep sedimentary formations

Abstract: This paper provides a review of the geomechanics and modeling of geomechanics associated with geologic carbon storage (GCS), focusing on storage in deep sedimentary formations, in particular saline aquifers. The paper first introduces the concept of storage in deep sedimentary formations, the geomechanical processes and issues related with such an operation, and the relevant geomechanical modeling tools. This is followed by a more detailed review of geomechanical aspects, including reservoir stress-strain and microseismicity, well integrity, caprock sealing performance, and the potential for fault reactivation and notable (felt) seismic events. Geomechanical observations at current GCS field deployments, mainly at the In Salah CO2 storage project in Algeria, are also integrated into the review. The In Salah project, with its injection into a relatively thin, low-permeability sandstone is an excellent analogue to the saline aquifers that might be used for large scale GCS in parts of Northwest Europe, the U.S. Midwest, and China. Some of the lessons learned at In Salah related to geomechanics are discussed, including how monitoring of geomechanical responses is used for detecting subsurface geomechanical changes and tracking fluid movements, and how such monitoring and geomechanical analyses have led to preventative changes in the injection parameters. Recently, the importance of geomechanics has become more widely recognized among GCS stakeholders, especially with respect to the potential for triggering notable (felt) seismic events and how such events could impact the long-term integrity of a CO2 repository (as well as how it could impact the public perception of GCS). As described in the paper, to date, no notable seismic event has been reported from any of the current CO2 storage projects, although some unfelt microseismic activities have been detected by geophones. However, potential future commercial GCS operations from large power plants will require injection at a much larger scale. For such large-scale injections, a staged, learn-as-you-go approach is recommended, involving a gradual increase of injection rates combined with continuous monitoring of geomechanical changes, as well as siting beneath a multiple layered overburden for multiple flow barrier protection, should an unexpected deep fault reactivation occur.

Microstructure Investigation in Unsaturated Soils: A Review with Special Attention to Contribution of Mercury Intrusion Porosimetry and Environmental Scanning Electron Microscopy

Abstract: With the advent of modern microstructural testing techniques and microstructure based constitutive models the microstructural characterisation of soils is gaining prominence. This paper reviews the history of microstructure investigation in unsaturated soils and discusses the engineering significance of this research to date. After a brief overview of the main microstructural techniques, the paper focuses on the evaluation of the current state of use and the development of two widely used techniques to study the microstructure of partially saturated soils, namely mercury intrusion porosimetry and the environmental scanning electron microscopy. The details of these techniques, their advantages and limitations, are first covered, followed by the presentation of selected test results. These results highlight the use of these techniques for understanding different hydro-mechanical behavioural features observed at macroscopic scale. Specifically, the paper shows the use of these techniques to explore the fundamental properties of water retention characteristics, water permeability, and micro and macrostructural interactions along different hydro-mechanical paths.

Influence of gas production induced volumetric strain on permeability of coal

Abstract: The gas permeability of a coalbed, unlike that of conventional gas reservoirs, is influenced during gas production not only by the simultaneous changes in effective stress and gas slippage, but also by the volumetric strain of the coal matrix that is associated with gas desorption. A technique for conducting laboratory experiments to separate these effects and estimate their individual contribution is presented in this paper. The results show that for a pressure decrease from 6.2 to 0.7 MPa, the total permeability of the coal sample increased by more than 17 times. A factor of 12 is due to the volumetric strain effect, and a factor of 5 due to the gas slippage effect. Changes in permeability and porosity with gas depletion were also estimated using the measured volumetric strain and the matchstick reservoir model geometry for flow of gas in coalbeds. The resulting variations were compared with results obtained experimentally. Furthermore, the results show that when gas pressure is above 1.7 MPa, the effect of volumetric strain due to matrix shrinkage dominates. As gas pressure falls below 1.7 MPa, both the gas slippage and matrix shrinkage effects play important roles in influencing the permeability. Finally, the change in permeability associated with matrix shrinkage was found to be linearly proportional to the volumetric strain. Since volumetric strain is linearly proportional to the amount of gas desorbed, the change in permeability is a linear function of the amount of desorbing gas.

A Review of the Tensile Strength of Rock: Concepts and Testing

Abstract: A review of the tensile strength of rock was conducted to determine the relationship between direct tensile strength (DTS) and Brazilian tensile strength (BTS) and to examine the validity of estimating tensile strength from other measured properties, such as the crack initiation (CI) threshold. A data set was gathered from the existing literature where tensile values could be reliably correlated with unconfined compressive strength or CI values. It was determined that the BTS obtained in standard testing is generally greater than the equivalent DTS and that this relationship is rock type dependent. CI yields a reasonable estimate of tensile strength and this correlation is improved when the BTS values are reduced to DTS values by rock type specific correlations. The factor f, in DTS = f BTS, can be considered to be approximately 0.9 for metamorphic, 0.8 for igneous and 0.7 for sedimentary rocks. The relationships presented demonstrate that there is wide scatter in the available data for estimating tensile strength likely due to both specimen variability and testing configuration, including platen geometry and relative stiffness. Estimates of tensile strength should only be used for preliminary design purposes and measurements should be made to confirm preliminary assumptions for each design.

Design and Application of Underground Mine Paste Backfill Technology

Abstract: This paper reviews the design and application of paste backfill in underground hard rock mines used as ground support for pillars and walls, to help prevent caving and roof falls, and to enhance pillar recovery for improved productivity. Arching after stope filling reduces vertical stress and increases horizontal stress distribution within the fill mass. It is therefore important to determine horizontal stress on stope sidewalls using various predictive models in the design of paste backfill. Required uniaxial compressive strength (UCS) for paste backfill depends on the intended function, such as vertical roof support, development opening within the backfill, pillar recovery, ground or pillar support, and working platform. UCS design models for these functions are given. Laboratory and backfill plant scale designs for paste backfill mix design and optimization are presented, with emphasis on initial tailings density control to prevent under-proportioning of binder content. Once prepared, paste backfill is transported (or pumped) and placed underground by pipeline reticulation. The governing elements of paste backfill transport are rheological factors such as shear yield stress, viscosity, and slump height (consistency). Different models (analytical, semi-empirical, and empirical) are given to predict the rheological factors of paste backfill (shear yield stress and viscosity). Following backfill placement underground, self-weight consolidation settlement, internal pressure build-up, the arching effect, shrinkage, stope volume, and wall convergence against backfill affect mechanical integrity.