Showing papers in "International Communications in Heat and Mass Transfer in 2023"

TL;DR: In this article , the authors proposed four CFF distribution forms with filling rate of 30% to improve the thermal performance of LTESU, and the experimental results showed that LDD-CFF showed the highest performance.

TL;DR: In this paper , mathematical modeling and interpretation of non-Newtonian tangent-hyperbolic rheological model capturing multi-physical effects is performed under nonlinear buoyancy forces and magnetohydrodynamics towards stratified convectively heated surface.

TL;DR: In this paper , the authors combined solvent extraction and microfluidic technology to separate and extract Ca2+ ions in the serpentine microchannel, achieving a performance of 62.34% and 23.40% at a residence time of 4.2 s.

TL;DR: In this article , a mathematical framework for the hemodynamical characterization of blood circulation loaded with trihybrid nanoparticles inside an eccentric endoscopic arterial canal with a flexible wall under the interference of buoyancy and electro-osmotic forces is presented.

TL;DR: In this paper , the Darcy-Forchheimer-Brinkman model is used to model the fluid transport within the porous medium, where carbon nanotubes and alumina ceramics are considered nanoparticles and porous media, respectively.

TL;DR: In this paper , the authors simulate a standing-wave thermoacoustic engine (SWTAE) system by capturing its nonlinear thermo-acoustic features with three-dimensional (3D) unsteady Reynolds-Averaged Navier-Stokes (URANS) and hybrid URANS/LES (Large Eddy Simulation) models such as Detached-Eddy Simulations (DES) and stress-blended Eddy simulation (SBES) models.

TL;DR: In this article , the scaling similarity transformations are employed to convert nonlinear partial differential equations to the nonlinear ordinary differential equations, after converting equations from dimensional to non-dimensional, they will use the BVP4C solver (MATLAB) for plotting the graphs to analyze how distinct nondimensional parameters effecting the Skin friction and Nusselt number transfer rate for both hybrid fluid (Graphene + Magnesium oxide) case and ternary hybrid nanomaterial (Gramhene+ Zirconium oxide +Magnesium oxide).

TL;DR: In this article , an optimization study based on the response surface method (RSM) is carried out on the low-temperature preheating strategy of lithium-ion batteries using SPCMs to obtain a lightweight design with satisfactory performance.

TL;DR: In this paper , the authors analyzed the dynamics of MHD rotational stagnation point flow of Maxwell nanofluid of temperature-dependent viscosity towards a radially stretching rotating disk.

TL;DR: In this paper , a highly mixed convection due to the movements of two perpendicular walls of odd-shaped enclosures is examined, where the components of the ternary nanofluids are spherical Al2O3 nanoparticles, MWCNT cylindrical nanoparticles and platelet graphene nanoparticles.

TL;DR: In this paper , a hydrodynamic equilibrium model of opposed spilling fire is established incorporating viscous friction, inertia force, gravity, and surface tension, and the critical discharge flow rate is calculated based on the hydrodynamics analysis of subsurface flow region.

TL;DR: In this article , a review of thermal conductivity enhancers (TCEs) for thermal control of electronic components using phase-change materials (PCMs) in heat sinks is presented.

TL;DR: In this article , the authors analyzed the energy consumption of water treatment technologies and showed that conventional methods like coagulation and sedimentation are characterized by quite low energy demand, whereas more advanced membrane techniques consumed much more energy.

TL;DR: In this article , the authors discuss the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank.

TL;DR: In this article , the three-dimensional (3D) fluid flow and heat transfer analysis and geometric optimization of two rows circular and elliptic wavy fin and tube heat exchanger (FTHE) are numerically examined for staggered arrangement.

TL;DR: In this article , bifurcated fractal fin inspired by leaf venation structures in nature are inserted into a typical vertical rectangular cavity to improve the thermal transmission performance of latent heat thermal energy storage systems.

TL;DR: In this article , the authors derived an analytical solution for the transient axisymmetric temperature distribution in a cylindrical geometry with time-varying boundary conditions, which extends their previous result for constant-temperature boundary conditions.

TL;DR: In this paper , the authors investigate the emerging adsorbents for adsorption desalination cum cooling system (ADCS) from the viewpoints of water production potential (WPP), specific cooling potential (SCP), energy required (ER), and coefficient of performance (COP).

TL;DR: In this article , the thermal energy is transported in time-dependent axisymmetric flow that is created by a stretchable cylinder with thermophoretic particle deposition and Soret-Dufour effects.

TL;DR: In this article , the authors focused on the under-explored aspect of heat exchanger optimization for HFC-based adsorbents through numerical analysis of two finned tube heat exchange configurations, viz., annular and longitudinal, and highlighted the significance of the adsorbent's thermal conductivity in realizing compact lightweight heat exchangers.

TL;DR: In this article , the effect of heat release distribution on the dynamic mode transition process of the ejector-to-ramjet in RBCC engine under Ma∞ = 3, T0 = 630 K flight condition is investigated through numerical simulations.

TL;DR: In this paper , the authors presented a theoretical model to determine the steady state temperature distribution in a general M-layer structure with spatial variation in thermal contact resistance between adjacent layers, and the coefficients were determined from algebraic equations derived from the given spatially varying thermal contact resistances.

TL;DR: In this paper , a thermal energy storage (TES) with phase change material (PCM) to a photovoltaic (PV) installation was designed with the use of an electric heater for charging and water for discharge.

TL;DR: In this article , a modified Wilson plot method was used to determine the multiplier (C) and Reynolds number exponential (n) for the coolant side as −0.426 and 0.494, respectively.

TL;DR: In this paper , the authors used deep learning, genetic algorithm, and multicriteria decision analysis applied to a desiccant cooling system working under real transient experimental conditions of a building located in Austria.

TL;DR: In this article , the authors investigated the thermal exchange and vapor transfer involving ignition of extremely flammable liquids by neighbouring pool fire and calculated the mean radiative heat flux of the pool to be ignited using double integration of the horizontal viewing angle coefficient of cylinder flame model.

TL;DR: In this paper , the authors used 3D enhanced tube and smooth tube with an inner diameter of 9.52 mm to study the condensation heat transfer performance with R410A and R32 as the working fluids at different mass flow rates and vapor qualities.

TL;DR: In this paper , two types of vapour chambers with integrated 3D printed wicks were designed, printed, and tested to demonstrate the feasibility of constructing VCs through metallic additive manufacturing and a water-cooling test system was established to study the temperature distribution, thermal resistance, and maximum heat transfer power of the VCs.

TL;DR: In this paper , a deep learning-based reduced-order model (ROM) is proposed to replace the CFD model to accelerate the optimization of the thermal placement of the multichip modules.

TL;DR: In this article , the effect of suction and injection over a Marangoni boundary layer flow on magnetohydrodynamics (MHD) Casson fluid and thermal radiation on a permeable surface was investigated.