Showing papers on "Scramjet published in 1974"

Performance of an inlet for an integrated scramjet concept

Abstract: Review of the results of an experimental investigation of the performance of an inlet for an integrated scramjet engine concept at Mach 6. Following a description of the inlet design and test model, the Mach 6 experimental results obtained are presented in terms of integrated performance parameters.

Scramjet nozzle design and analysis as applied to a highly integrated hypersonic research airplane

Abstract: The configuration and performance of the propulsion system for the hypersonic research vehicle are discussed. A study of the interactions between propulsion and aerodynamics of the highly integrated vehicle was conducted. The hypersonic research vehicle is configured to test the technology of structural and thermal protection systems concepts and the operation of the propulsion system under true flight conditions for most of the hypersonic flight regime. The subjects considered are: (1) research vehicle and scramjet engine configurations to determine fundamental engine sizing constraints, (2) analytical methods for computing airframe and propulsion system components, and (3) characteristics of a candidate nozzle to investigate vehicle stability and acceleration performance.

An examination of injector/combustor design effects on scramjet performance

Abstract: Description of a simplified one-dimensional treatment of fuel injection for supersonic combustor performance analysis. Representative mixing efficiency variations for both parallel and cross-stream injection are obtained, and approximate means for estimating the length required for complete mixing are demonstrated. Comparisons of calculated and measured data show good agreement.

A forebody design technique for highly integrated bottom-mounted scramjets with application to a hypersonic research airplane

Abstract: An inviscid technique for designing forebodies which produce uniformly precompressed flows at the inlet entrance for bottom-mounted scramjets has been developed so that geometric constraints resulting from design trade-offs can be effectively evaluated. The flow fields resulting from several forebody designs generated in support of a hypersonic research airplane conceptual design study have been analyzed in detail with three-dimensional characteristics calculations to verify the uniform flow conditions. For the designs analyzed, uniform flow is maintained over a wide range of flight conditions (Mach number equals 4 to 10; angle of attack equals 6 deg to 10 deg) corresponding to scramjet operation flight envelope of the research airplane.

Turbulent heat transfer prediction method for application to scramjet engines

Abstract: An integral method for predicting boundary layer development in turbulent flow regions on two-dimensional or axisymmetric bodies was developed. The method has the capability of approximating nonequilibrium velocity profiles as well as the local surface friction in the presence of a pressure gradient. An approach was developed for the problem of predicting the heat transfer in a turbulent boundary layer in the presence of a high pressure gradient. The solution was derived with particular emphasis on its applicability to supersonic combustion; thus, the effects of real gas flows were included. The resulting integrodifferential boundary layer method permits the estimation of cooling reguirements for scramjet engines. Theoretical heat transfer results are compared with experimental combustor and noncombustor heat transfer data. The heat transfer method was used in the development of engine design concepts which will produce an engine with reduced cooling requirements. The Langley scramjet engine module was designed by utilizing these design concepts and this engine design is discussed along with its corresponding cooling requirements. The heat transfer method was also used to develop a combustor cooling correlation for a combustor whose local properties are computed one dimensionally by assuming a linear area variation and a given heat release schedule.

Aerodynamic drag and fuel spreading measurements in a simulated scramjet combustion module

Abstract: The drag of a simulated scramjet combustion module was measured at Mach 2, 2.5, and 3. The combustor was rectangular in cross section and incorporated six swept fuel injector struts. The effect of strut leading edge radius, position of maximum thickness, thickness ratio, sweep angle, and strut length on the drag was determined. Reduction in thickness ratio had the largest effect on drag reduction. Sweeping the struts upstream yielded the same drag as sweeping the struts downstream and potentially offers the advantages of increased mixing time for the fuel. Helium injection was used to simulate hydrogen fuel. The interstrut spacing required to achieve good distribution of fuel was was found to be about 10 jet diameters. The contribution of helium injection to drag reduction was small.

Drag and distribution measurements of single-element fuel injectors for supersonic combustors

Abstract: The drag caused by several vortex generating fuel injectors for scramjet combustors was measured in a Mach 2 to 3.5 airstream. Injector drag was found to be strongly dependent on injector thickness ratio. The distribution of helium injected into the stream was measured both in the near field and the far field of the injectors for a variety of pressure ratios. The far field results differed appreciably from measurements in the near field. Injection pressure ratio was found to profoundly influence the penetration. One of the aerowing configurations tested yielded low drag consistent with desirable penetration and spreading characteristics.

Performance of a hydrogen burner to simulate air entering scramjet combustors

Abstract: Tests were conducted to determine the performance of a hydrogen burner used to produce a test gas that simulates air entering a scramjet combustor at various flight conditions. The test gas simulates air in that it duplicates the total temperature, total pressure, and the volume fraction of oxygen of air at flight conditions. The main objective of the tests was to determine the performance of the burner as a function of the effective exhaust port area. The conclusions were: (1) pressure oscillations of the chugging type were reduced in amplitude to plus or minus 2 percent of the mean pressure level by proper sizing of hydrogen, oxygen, and air injector flow areas; (2) combustion efficiency remained essentially constant as the exhaust port area was increased by a factor of 3.4; (3) the mean total temperature determined from integrating the exit radial gas property profiles was within plus or minus 5 percent of the theoretical bulk total temperature; (4) the measured exit total temperature profile had a local peak temperature more than 30 percent greater than the theoretical bulk total temperature; and (5) measured heat transfer to the burner liner was 75 percent of that predicted by theory based on a flat radial temperature profile.

Methodology for Three Dimensional Nozzle Design

Abstract: Criteria for the selection and methods of analysis for designing a hypersonic scramjet nozzle are discussed. The criteria are based on external and internal flow requirements, related to drag, lift, and pitching moments of the vehicle and thrust of the engine. The steps involved in establishing the criteria are analyzed. Mathematical models of the design procedure are provided.

Heat conduction controlled combustion for scramjet applications

Abstract: The use of heat conduction flame generated in a premixed supersonic stream is discussed. It is shown that the flame is controlled initially by heat conduction and then by chemical reaction. Such a flame is shorter than the diffusion type of flame and therefore it requires a much shorter burner. The mixing is obtained by injecting the hydrogen in the inlet. Then the inlet can be cooled by film cooling.

A source flow characteristic technique for the analysis of scramjet exhaust flow field

Abstract: The factors which influence the design and selection of a nozzle for a hypersonic scramjet are described. A two dimensional second-order characteristic procedure capable of analyzing the aerodynamic performance of typical nozzle configurations is presented. Equations of motion governing the two dimensional, axisymmetric, or axially expanding inviscid flow of a gas mixture, with frozen chemistry, are provided. Diagrams of the flow conditions for various configurations are included.

An aerodynamic study of scramjet fuel injectors

Abstract: The aerodynamic drag and fuel distribution patterns of injectors designed for a supersonic combustion ramjet were measured at Mach numbers of 2, 2.5, and 3. The most significant parameter effecting the drag was found to be the injector thickness ratio. A two-fold reduction in the thickness ratio caused a 65 percent decrease in drag. Changing the injector sweep angle a factor of 2 resulted in only a small change in drag. A reversal of injector sweep, from sweepback to sweepforward, did not change the measured drag. Helium gas was injected through the struts to simulate the penetration and spreading patterns of hydrogen. Sampling measurements were made at approximately 2 duct heights downstream of the combustor. The spacing required between fuel injectors was found to be about 10 jet diameters. The effect of gas injection on the measured drag was found to be minor.

Hypersonic ramjet experiment project. Phase 1: Computer program description, ramjet and scramjet cycle performance

Abstract: A computer program was developed to describe the performance of ramjet and scramjet cycles. The program performs one dimensional calculations of the equilibrium, real-gas internal flow properties of the engine. The program can be used for the following: (1) preliminary design calculation and (2) design analysis of internal flow properties corresponding to stipulated flow areas. Only the combustion of hydrogen in air is considered in this case.