Additive manufacturing of metallic components – Process, structure and properties

Oxygen, one of the most abundant elements on Earth, often forms an undesired interstitial impurity or ceramic phase (such as an oxide particle) in metallic materials. Even when it adds strength, oxygen doping renders metals brittle1–3. Here we show that oxygen can take the form of ordered oxygen complexes, a state in between oxide particles and frequently occurring random interstitials. Unlike traditional interstitial strengthening4,5, such ordered interstitial complexes lead to unprecedented enhancement in both strength and ductility in compositionally complex solid solutions, the so-called high-entropy alloys (HEAs)6–10. The tensile strength is enhanced (by 48.5 ± 1.8 per cent) and ductility is substantially improved (by 95.2 ± 8.1 per cent) when doping a model TiZrHfNb HEA with 2.0 atomic per cent oxygen, thus breaking the long-standing strength–ductility trade-off11. The oxygen complexes are ordered nanoscale regions within the HEA characterized by (O, Zr, Ti)-rich atomic complexes whose formation is promoted by the existence of chemical short-range ordering among some of the substitutional matrix elements in the HEAs. Carbon has been reported to improve strength and ductility simultaneously in face-centred cubic HEAs12, by lowering the stacking fault energy and increasing the lattice friction stress. By contrast, the ordered interstitial complexes described here change the dislocation shear mode from planar slip to wavy slip, and promote double cross-slip and thus dislocation multiplication through the formation of Frank–Read sources (a mechanism explaining the generation of multiple dislocations) during deformation. This ordered interstitial complex-mediated strain-hardening mechanism should be particularly useful in Ti-, Zr- and Hf-containing alloys, in which interstitial elements are highly undesirable owing to their embrittlement effects, and in alloys where tuning the stacking fault energy and exploiting athermal transformations13 do not lead to property enhancement. These results provide insight into the role of interstitial solid solutions and associated ordering strengthening mechanisms in metallic materials. Ordered oxygen complexes in high-entropy alloys enhance both strength and ductility in these compositionally complex solid solutions.

Enhanced strength and ductility in a high-entropy alloy via ordered oxygen complexes

Laser-based additive manufacturing (LBAM) processes can be utilized to generate functional parts (or prototypes) from the ground-up via layer-wise cladding – providing an opportunity to generate complex-shaped, functionally graded or custom-tailored parts that can be utilized for a variety of engineering applications. Directed Energy Deposition (DED), utilizes a concentrated heat source, which may be a laser or electron beam, with in situ delivery of powder- or wire-shaped material for subsequent melting to accomplish layer-by-layer part fabrication or single-to-multi layer cladding/repair. Direct Laser Deposition (DLD), a form of DED, has been investigated heavily in the last several years as it provides the potential to (i) rapidly prototype metallic parts, (ii) produce complex and customized parts, (iii) clad/repair precious metallic components and (iv) manufacture/repair in remote or logistically weak locations. DLD and Powder Bed Fusion-Laser (PBF-L) are two common LBAM processes for additive metal part fabrication and are currently demonstrating their ability to revolutionize the manufacturing industry; breaking barriers imposed via traditional, ‘subtractive’ metalworking processes. This article provides an overview of the major advancements, challenges and physical attributes related to DLD, and is one of two Parts focused specifically on DLD. Part I (this article) focuses on describing the thermal/fluidic phenomena during the powder-fed DLD process, while Part II focuses on the mechanical properties and microstructure of parts manufactured via DLD. In this current article, a selection of recent research efforts – including methodology, models and experimental results – will be provided in order to educate the reader of the thermal/fluidic processes that occur during DLD, as well as providing important background information relevant to DLD as a whole. The thermal/fluid phenomena inherent to DLD directly influence the solidification heat transfer which thus impacts the part's microstructure and associated thermo-mechanical properties. A thorough understanding of the thermal/fluid aspects inherent to DLD is vital for optimizing the DLD process and ensuring consistent, high-quality parts.

An overview of Direct Laser Deposition for additive manufacturing; Part I: Transport phenomena, modeling and diagnostics

The present study contains a critical review of work on the formation of precipitates and intermetallic phases in dilute precipitation hardening Al–Cu–Mg based alloys with and without Li additions. Although many suggestions for the existence of pre-precipitates in Al–Cu–Mg alloys with a Cu/Mg atomic ratio close to 1 have been made, a critical review reveals that evidence exists for only two truly distinct ones. The precipitation sequence is best represented as: supersaturated solid solution→co-clusters→GPB2/S"→S where clusters are predominantly Cu–Mg co-clusters (also termed GPB or GPB I zones), GPB2/S" is an orthorhombic phase that is coherent with the matrix (probable composition Al10Cu3Mg3) for which both the term GPB2 and S" have been used, and S phase is the equilibrium Al2CuMg phase. GPB2/S" can co-exist with S phase before the completion of the formation of S phase. It is further mostly accepted that the crystal structure of S' (Al2CuMg) is identical to the equilibrium S phase (Al2CuMg). Th...

/pdf/precipitates-and-intermetallic-phases-in-precipitation-4vexo390vq.pdf

Precipitates and intermetallic phases in precipitation hardening Al–Cu–Mg–(Li) based alloys

The mechanical and microstructural properties of 316L stainless steel (SS) fabricated via Direct Laser Deposition (DLD), a laser-based additive manufacturing method, are presented and compared with those of conventionally-built counterparts. Using a Laser Engineered Net Shaping (LENS ® ) DLD system, the time interval between successive layer deposits, or inter-layer/idle time, for fabricating cylindrical specimens vertically-upward was varied by building either one or nine samples per build plate – thus increasing total assembly volume per build. Subsequently, the effect of thermal history, as well as heat treatment, on microstructural (i.e. grain size and morphology) and mechanical (i.e. tensile, compression, and microhardness) properties of DLD parts were investigated. Results indicate that the DLD 316L SS samples produced herein have a higher yield and ultimate tensile strength relative to their cast and wrought forms. Furthermore, the thermal history, microstructural evolution, and mechanical properties of DLD 316L SS are shown to be dependent on the time interval between deposits. Longer local time intervals result in higher cooling rates, leading to finer microstructures, higher/uniform strength and lower elongation to failure. In addition, porosity and less integral metallurgical bonds are found to be more prevalent in locations further upward from the build plate due to reduced laser penetration depths (e.g. previous-layer remelting decreases). Conversely, parts manufactured with shorter time intervals were found to possess a coarser microstructure, lower strength and higher elongation to failure – attributable to lower cooling rates caused by an increased bulk temperature in the part. These results may aid in future design and control of more efficient, constant-power DLD processes – especially with regard to building multiple and/or larger parts; an approach desirable for minimizing small-to-medium lot production times.

Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel

A simple method of metal foam production is to introduce a blowing agent (e.g. TiH2) into an aluminium melt containing foam stabilisers such as oxides (usually Ca-based) and/or particles (e.g. SiC, Al2O3). In this work, Al/SiC composites (in-house and commercial Duralcan) [both of them with LM25 matrix (Al–7Si–0.3Mg)] containing particles of various sizes and contents were foamed at different temperatures using TiH2. Foamability is characterised through their expansion and collapse. It is observed that high expansions and good quality foams could be obtained upon manipulating SiC particle size and content. However, irrespective of particle size/vol.% combination, significant effect of foaming temperature is noticed on the fundamental stability of the liquid foam until solidification. Both cell size and foam density varied along the ingot height. The distribution of SiCP within the cell wall is random with no preferential segregation to gas/metal interface. The evolution of foam, and the role of SiC on foam stability are discussed based on macro and cell wall microstructural results.

Processing and Stability of LM25/SiCP Composite Foams

A first-of-its-kind look-up matrix for determining ideal foam density against a spectrum of blast loads is developed to design an efficient foam-based blast absorber. A numerical study is carried o...

Evaluation of optimum foam density for effective design of blast absorbers

Mechanical working of Al–Li alloys is primarily concerned with aerospace alloy rolled products (sheet and plate), extrusions, and to a lesser extent forgings. These products are fabricated by hot working with intermittent and final heat treatments. This thermomechanical processing (TMP) can be rather complex for the modern 3rd generation Al-Li alloys, but is necessary to obtain optimum combinations of properties.

This Chapter is in two parts. Part 1 discusses the ‘workability’ of metals and alloys and the hot deformation characteristics of Al–Li alloys, leading to the concept of Process Maps. A comprehensive Process Map for a binary Al–Li alloy illustrates the usefulness of these Maps for defining temperature–strain rate regions for safe and unsafe hot working, recrystallization and recovery, and superplastic behaviour

Part 2 provides some general considerations about processing Al–Li alloy products, followed by a review and discussion of the currently available information for 3rd generation alloys. It is concluded that their complex TMP schedules may make it difficult to obtain optimum combinations of properties for thicker products.

Mechanical Working of Aluminum–Lithium Alloys

Microstructural modifications and their effect on tensile properties in an Fe-7  wt.% Al alloy by additions of 0.5% TiB2, 0.5% ZrB2 or both has been studied. Alloys are examined in the as-cast as well as in the hot-rolled and annealed conditions. Solidification structure of the Vacuum Arc Remelted pancake ingots was columnar dendritic. Further, boride modified alloys are found to have finer grains in as-cast as well as in hot-rolled and annealed conditions. In the annealed condition, boride containing alloys were found to have superior tensile yield strength, ductility and strain hardening behaviour. These property improvements are attributed to boride aided grain refinement during casting as well as during thermo-mechanical processing of the steels.

Effect of TiB2 and ZrB2 additions on structure and properties of Fe-7Al based light weight steel

In the present work, complex powder alloys containing spinel as a minor phase were produced by mechanical alloying in a high-energy planetary ball mill from a 33Al–45Cu–22Fe (at.%) powder blend. These alloys show characteristics suitable for the synthesis of promising catalysts. The alloying was conducted in two stages: at the first stage, a Cu+Fe powder mixture was ball-milled for 90 min; at the second stage, Al was added, and the milling process was continued for another 24 min. The main products of mechanical alloying formed at each stage were studied using X-ray diffraction phase analysis, Mössbauer spectroscopy, transmission electron microscopy, and energy-dispersive spectroscopy. At the end of the first stage, crystalline iron was not found. The main product of the first stage was a metastable Cu(Fe) solid solution with a face-centered cubic structure. At the second stage, the Cu(Fe) solid solution transformed to Cu(Al), several Fe-containing amorphous phases, and a spinel phase. The products of the two-stage process were different from those of the single-stage mechanical alloying of the ternary elemental powder mixture; the formation of undesirable intermediate phases was avoided, which ensured excellent composition uniformity. A sequence of solid-state reactions occurring during mechanical alloying was proposed. Mesopores and a spinel phase were the features of the two-stage milled material (both are desirable for the target catalyst).

/pdf/elimination-of-composition-segregation-in-33al-45cu-22fe-at-2wjj2edj.pdf

Amol A. Gokhale

Papers

Processing and Stability of LM25/SiCP Composite Foams

Evaluation of optimum foam density for effective design of blast absorbers

Mechanical Working of Aluminum–Lithium Alloys

Effect of TiB2 and ZrB2 additions on structure and properties of Fe-7Al based light weight steel

Elimination of Composition Segregation in 33Al–45Cu–22Fe (at.%) Powder by Two-Stage High-Energy Mechanical Alloying