Single-walled carbon nanotubes (SWCNTs) have been attracting tremendous attention owing to their structure (chirality) dependent outstanding properties, which endow them with great potential in a wide range of applications. The preparation of chirality-pure SWCNTs is not only a great scientific challenge but also a crucial requirement for many high-end applications. As such, research activities in this area over the last two decades have been very extensive. In this review, we summarize recent achievements and accumulated knowledge thus far and discuss future developments and remaining challenges from three aspects: controlled growth, postsynthesis sorting, and characterization techniques. In the growth part, we focus on the mechanism of chirality-controlled growth and catalyst design. In the sorting part, we organize and analyze existing literature based on sorting targets rather than methods. Since chirality assignment and quantification is essential in the study of selective preparation, we also include in the last part a comprehensive description and discussion of characterization techniques for SWCNTs. It is our view that even though progress made in this area is impressive, more efforts are still needed to develop both methodologies for preparing ultrapure (e.g., >99.99%) SWCNTs in large quantity and nondestructive fast characterization techniques with high spatial resolution for various nanotube samples.

Chirality Pure Carbon Nanotubes: Growth, Sorting, and Characterization.

Hydroxyapatite (HA) coatings have numerous applications in orthopedics and dentistry, owing to their excellent ability to promote stronger implant fixation and faster bone tissue ingrowth and remodeling. Thermal plasma spray and other plasma-assisted techniques have recently been used to synthesize various calcium phosphate-based bioceramics. Despite notable recent achievements in the desired stoichiometry, phase composition, mechanical, structural, and bio-compatible properties, it is rather difficult to combine all of the above features in a single coating. For example, many existing plasma-sprayed HA coatings fall short in meeting the requirements of grain size and crystallinity, and as such are subject to enhanced resorption in body fluid. On the other hand, relatively poor interfacial bonding and stability is an obstacle to the application of the HA coatings in high load bearing Ti6Al4V knee joint implants. Here, we report on an alternative: a plasma-assisted, concurrent, sputtering deposition technique for high performance biocompatible HA coatings on Ti6Al4V implant alloy. The plasma-assisted RF magnetron co-sputtering deposition method allows one to simultaneously achieve most of the desired attributes of the biomimetic material and overcome the aforementioned problems. This article details the film synthesis process specifications, extensive analytical characterization of the material's properties, mechanical testing, simulated body fluid assessments, biocompatibility and cytocompatibility of the HA-coated Ti6Al4V orthopedic alloy. The means of optimization of the plasma and deposition process parameters to achieve the desired attributes and performance of the HA coating, as well as future challenges in clinical applications are also discussed.

RF plasma sputtering deposition of hydroxyapatite bioceramics : synthesis, performance, and biocompatibility

In recent years, photoelectronic synaptic devices have emerged as a platform for use in next-generation neuromorphic systems and artificial neural networks (ANNs). In this paper, we report an artificial photoelectronic synapse based on an ion-gel gated In-Zn-O phototransistor. The phototransistor is stimulated by a deep ultraviolet light spike, and it can process and store information in the form of an electric current. Key biological synaptic behaviors were investigated, including excitatory post-synaptic current and paired pulse facilitation. Furthermore, channel conduction can be changed by photoelectric synergy in order to simulate potentiation and depression behavior in the human brain. Most importantly, four forms of spike-timing dependent plasticity learning principles were realized by a photoelectric hybrid stimulation. Our studies provide a path towards hybrid photoelectronic ANNs capable of performing solar-blind sensitive tasks.

Deep-ultraviolet-triggered neuromorphic functions in In-Zn-O phototransistors

Metal oxide resistive switching memories have been a crucial component for the requirements of the Internet of Things, which demands ultra-low power and high-density devices with new computing principles, exploiting low cost green products and technologies. Most of the reported resistive switching devices use conventional methods (physical and chemical vapor deposition), which are quite expensive due to their up-scale production. Solution-processing methods have been improved, being now a reliable technology that offers many advantages for resistive random-access memory (RRAM) such as high versatility, large area uniformity, transparency, low-cost and a simple fabrication of two-terminal structures. Solution-based metal oxide RRAM devices are emergent and promising non-volatile memories for future electronics. In this review, a brief history of non-volatile memories is highlighted as well as the present status of solution-based metal oxide resistive random-access memory (S-RRAM). Then, a focus on describing the solution synthesis parameters of S-RRAMs which induce a massive influence in the overall performance of these devices is discussed. Next, a precise analysis is performed on the metal oxide thin film and electrode interface and the recent advances on S-RRAM that will allow their large-area manufacturing. Finally, the figures of merit and the main challenges in S-RRAMs are discussed and future trends are proposed.

Recent Progress in Solution-Based Metal Oxide Resistive Switching Devices.

Single-walled carbon nanotubes (SWNTs) are a family of molecules that have the same cylindrical shape but different chiralities. Many fundamental studies and technological applications of SWNTs require a population of tubes with identical chirality that current syntheses cannot provide. The SWNT sorting problem—that is, separation of a synthetic mixture of tubes into individual single-chirality components—has attracted considerable attention in recent years. Intense efforts so far have focused largely on, and resulted in solutions for, a weaker version of the sorting problem: metal/semiconductor separation. A systematic and general method to purify each and every single-chirality species of the same electronic type from the synthetic mixture of SWNTs is highly desirable, but the task has proven to be insurmountable to date. Here we report such a method, which allows purification of all 12 major single-chirality semiconducting species from a synthetic mixture, with sufficient yield for both fundamental studies and application development. We have designed an effective search of a DNA library of ∼1060 in size, and have identified more than 20 short DNA sequences, each of which recognizes and enables chromatographic purification of a particular nanotube species from the synthetic mixture. Recognition sequences exhibit a periodic purine–pyrimidines pattern, which can undergo hydrogen-bonding to form a two-dimensional sheet, and fold selectively on nanotubes into a well-ordered three-dimensional barrel. We propose that the ordered two-dimensional sheet and three-dimensional barrel provide the structural basis for the observed DNA recognition of SWNTs.

http://ma.ecsdl.org/content/MA2010-01/32/1520.full.pdf

(Invited) DNA Sequence Motifs for Structure-Specific Recognition and Separation of Carbon Nanotubes

The discovery of resistance switching memristors marks a paradigm shift in the search for alternative non-volatile memory components in the semiconductor industry. Normally a dielectric in these bistable memory cells changes its resistance with an applied electric field or current, albeit retaining the resistive state based on the history of the applied field. Despite showing immense potential, sustainable growth of this new memory technology is bogged down by several factors including cost, intricacies of design, lack of efficient tunability, and issues with scalability and eco-friendliness. Here, we demonstrate a simple arrangement wherein an ethanol-adsorbed ZnO thin film exhibits orders of magnitude change in resistance when activated by visible light. We show that there exists two stable ohmic states, one in the dark and the other in the illuminated regime, as well as a significant delay in the transition between these saturated states. We also demonstrate that visible light acts as a non-invasive tuning parameter for the bistable resistive states. Furthermore, a pinched hysteresis I-V response observed in these devices indicate what seems to be a new type of memristive behaviour.

/pdf/resistance-switching-and-memristive-hysteresis-in-visible-4ptahtfhuh.pdf

Resistance Switching and Memristive Hysteresis in Visible-Light-Activated Adsorbed ZnO Thin Films

Single-walled carbon nanotubes (SWCNTs) are a class of 1D nanomaterials that exhibit extraordinary electrical and optical properties. However, many of their fundamental studies and practical applications are stymied by sample polydispersity. SWCNTs are synthesized in bulk with broad structural (chirality) and geometrical (length and diameter) distributions; problematically, all known post-synthetic sorting methods rely on ultrasonication, which cuts SWCNTs into short segments (typically 10 µm) SWCNTs can be efficiently separated from shorter ones through a solution-phase "self-sorting". It is shown that thin-film transistors fabricated from long semiconducting SWCNTs exhibit a carrier mobility as high as ≈90 cm2 V-1 s-1 , which is ≈10 times higher than those which use shorter counterparts and well exceeds other known materials such as organic semiconducting polymers (<1 cm2 V-1 s-1 ), amorphous silicon (≈1 cm2 V-1 s-1 ), and nanocrystalline silicon (≈50 cm2 V-1 s-1 ). Mechanistic studies suggest that this self-sorting is driven by the length-dependent solution phase behavior of rigid rods. This length sorting technique shows a path to attain long-sought ultralong, electronically pure carbon nanotube materials through scalable solution processing.

Self-Sorting of 10-µm-Long Single-Walled Carbon Nanotubes in Aqueous Solution

For thousands of years, carbon ink has been used as a black color pigment for writing and painting purposes. However, recent discoveries of nanocarbon materials, including fullerenes, carbon nanotubes, graphene, and their various derivative forms, together with the advances in large-scale synthesis, are enabling a whole new generation of carbon inks that can serve as an intrinsically programmable materials platform for developing advanced functionalities far beyond color. The marriage between these multifunctional nanocarbon inks with modern printing technologies is facilitating and even transforming many applications, including flexible electronics, wearable and implantable sensors, actuators, and autonomous robotics. This review examines recent progress in the reborn field of carbon inks, highlighting their programmability and multifunctionality for applications in flexible electronics and stimuli-responsive devices. Current challenges and opportunities will also be discussed from a materials science perspective towards the advancement of carbon ink for new applications beyond color.

Beyond Color: The New Carbon Ink.

A simple and inexpensive method to generate plasma using a kitchen microwave oven is described in this paper. The microwave-generated plasma is characterized by spectroscopic analysis and compared with the absorption spectra of a gas discharge tube. A Paschen-like curve is observed as the microwave plasma initiation time is plotted as a function of the pressure of the plasma chamber. We have also demonstrated that this microwave-generated air plasma can be used in a multitude of applications such as: (a) surface modification of a substrate to change its wettability; (b) surface modification to change electrical/optical properties of a substrate; and (c) enhancement of adhesive forces for improved bonding of polymeric microfluidic molds, such as bonding polydimethylsiloxane (PDMS) chips to glass covers. These simple techniques of plasma generation and subsequent surface treatment and modification applications may bring new opportunities leading to new innovations not only in advanced labs, but also in undergraduate and even high school research labs.

/pdf/plasma-generation-by-household-microwave-oven-for-surface-5363a1inpp.pdf

Benjamin Barnes

Papers

Resistance Switching and Memristive Hysteresis in Visible-Light-Activated Adsorbed ZnO Thin Films

Self-Sorting of 10-µm-Long Single-Walled Carbon Nanotubes in Aqueous Solution

Beyond Color: The New Carbon Ink.

Plasma generation by household microwave oven for surface modification and other emerging applications

Cleanly Removable Surfactant for Carbon Nanotubes