A model for the axisymmetric growth and coalescence of small internal voids in elastoplastic solids is proposed and assessed using void cell computations. Two contributions existing in the literature have been integrated into the enhanced model. The first is the model of Gologanu-Leblond-Devaux, extending the Gurson model to void shape effects. The second is the approach of Thomason for the onset of void coalescence. Each of these has been extended heuristically to account for strain hardening. In addition, a micromechanically-based simple constitutive model for the void coalescence stage is proposed to supplement the criterion for the onset of coalescence. The fully enhanced Gurson model depends on the flow properties of the material and the dimensional ratios of the void-cell representative volume element. Phenomenological parameters such as critical porosities are not employed in the enhanced model. It incorporates the effect of void shape, relative void spacing, strain hardening, and porosity. The effect of the relative void spacing on void coalescence, which has not yet been carefully addressed in the literature. has received special attention. Using cell model computations, accurate predictions through final fracture have been obtained for a wide range of porosity, void spacing, initial void shape, strain hardening, and stress triaxiality. These predictions have been used to assess the enhanced model. (C) 2000 Elsevier Science Ltd. All rights reserved.

An extended model for void growth and coalescence

Ductile fracture models and their potential in local approach of fracture

Failure of metals I : brittle and ductile fracture

Publisher Summary An important failure mechanism in ductile metals and their alloys is by growth and coalescence of microscopic voids. In structural materials, the voids nucleate at inclusions and second-phase particles by decohesion of the particle–matrix interface or by particle cracking. Void growth is driven by plastic deformation of the surrounding matrix. Early micromechanical treatments of this phenomenon considered the growth of isolated voids. Later, constitutive equations for porous ductile solids were developed based on homogenization theory. Among these, the most widely known model was developed by Gurson for spherical and cylindrical voids.

/pdf/ductile-fracture-by-void-growth-to-coalescence-3rgsgx2sfa.pdf

Ductile Fracture by Void Growth to Coalescence

An extended model for void growth and coalescence - application to anisotropic ductile fracture

Experiments were performed on three heats of A508 class 3 steel in order to determine the mechanical conditions for cleavage fracture. These tests were carried out on various geometries including 4-point bend specimens and axisymmetric notched tensile bars with different notch radii which have been modelized using the finite element method. In one heat, the temperature range investigated was from 77 K to 233 K. It is shown that the cleavage resistance is increased by tensile straining. Moreover, the probability of fracture obeys the Weibull statistical distribution. All the results can be accounted for in terms of a local criterion based on Weibull theory and which takes into account the effect of plastic strain. In this criterion, the parameters which were experimentally determined are found to be temperature independent over the range 77 K to 170 K. The applicability of the approach proposed for cleavage fracture at the crack tip is also examined. It is shown that the experimental results published in the literature giving the variation of fracture toughness with temperature can be explained by the proposed criterion which predicts reasonably well both the scatter in the experimental results and theKICtemperature dependence.

A Local Criterion for Cleavage Fracture of a Nuclear Pressure Vessel Steel

Experimental study of cavity growth in ductile rupture

Ductile rupture of A508 steel under nonradial loading

— Fatigue crack growth measurements are usually made on standard specimens containing long cracks (∼10 mm) although in most practical situations, a large part of the fatigue life is spent with much shorter dimensions. The purpose of the present study is a comparison of crack growth behaviour for long cracks (∼13–16 mm) in CT specimens and smaller ones (∼0.3–0.5 mm) in four point bend specimens. Large effects are noticed indicating that, at a given stress intensity factor amplitude, the crack growth rate is significantly higher in specimens with short cracks. Mouth displacement measurements for both specimen configurations show that the crack closure phenomenon accounts for the observed effect. Crack closure is likely to be associated with fracture surface roughness as shown by partly machining the material left behind the crack tip in CT specimens.

F. Mudry

Papers

A Local Criterion for Cleavage Fracture of a Nuclear Pressure Vessel Steel

Experimental study of cavity growth in ductile rupture

Ductile rupture of A508 steel under nonradial loading

Short crack propagation and closure effects in a508 steel

An experimental program for the validation of local ductile fracture criteria using axisymmetrically cracked bars and compact tension specimens