VLSI Test Principles and Architectures: Design for Testability (Systems on Silicon)

This book is a comprehensive guide to new DFT methods that will show the readers how to design a testable and quality product, drive down test cost, improve product quality and yield, and speed up time-to-market and time-to-volume.

· Most up-to-date coverage of design for testability. 
· Coverage of industry practices commonly found in commercial DFT tools but not discussed in other books. 
· Numerous, practical examples in each chapter illustrating basic VLSI test principles and DFT architectures.
· Lecture slides and exercise solutions for all chapters are now available.
· Instructors are also eligible for downloading PPT slide files and MSWORD solutions files from the manual website.

Table of Contents

Chapter 1 - Introduction
Chapter 2 - Design for Testability
Chapter 3 - Logic and Fault Simulation 
Chapter 4 - Test Generation 
Chapter 5 - Logic Built-In Self-Test
Chapter 6 - Test Compression
Chapter 7 - Logic Diagnosis
Chapter 8 - Memory Testing and Built-In Self-Test
Chapter 9 - Memory Diagnosis and Built-In Self-Repair
Chapter 10 - Boundary Scan and Core-Based Testing
Chapter 11 - Analog and Mixed-Signal Testing
Chapter 12 - Test Technology Trends in the Nanometer Age

VLSI Test Principles and Architectures: Design for Testability

Power consumption of digital systems may increase significantly during testing. In this paper, systems equipped with a scan-based built-in self-test like the STUMPS architecture are analyzed, the modules and modes with the highest power consumption are identified, and design modifications to reduce power consumption are proposed. The design modifications include some gating logic for masking the scan path activity during shifting, and the synthesis of additional logic for suppressing random patterns which do not contribute to increase the fault coverage. These design changes reduce power consumption during BIST by several orders of magnitude, at very low cost in terms of area and performance.

https://www.iti.uni-stuttgart.de/fileadmin/rami/files/publications/2000/JETTA_GerstW2000.pdf

Minimized power consumption for scan-based BIST

This paper presents the ITC'02 SOC test benchmarks. The purpose of this new benchmark set is to stimulate research into new methods and tools for modular testing of SOCs and to enable the objective comparison of such methods and tools with respect to effectiveness and efficiency. The paper defines the benchmark format and naming scheme, and presents the benchmark SOCs. In addition, it provides an overview of the research problems that can be addressed and evaluated by means of this benchmark set. These research problems include the design of optimized test access infrastructures and test schedules.

A set of benchmarks for modular testing of SOCs

Scan architectures are commonly used to test digital circuitry in integrated circuits. This paper describes a method of adapting conventional scan architectures such that they operate in a low power mode during test. The adapted scan architectures maintain the test times of the pre-adapted scan architectures. Also, the adaptation occurs in a manner that enables the test patterns of the pre-adapted scan architecture to be directly reusable in the adapted scan architecture.

Adapting scan architectures for low power operation

A scan-based BIST scheme is presented which guarantees complete fault coverage with very low hardware overhead. A probabilistic analysis shows that the output of an LFSR which feeds a scan path has to be modified only at a few bits in order to transform the random patterns into a complete test set. These modifications may be implemented by a bit-flipping function which has the LFSR-state as an input, and flips the value shifted into the scan path at certain times. A procedure is described for synthesizing the additional bit-flipping circuitry, and the experimental results indicate that this mixed-mode BIST scheme requires less hardware for complete fault coverage than all the other scan-based BIST approaches published so far.

Bit-flipping BIST

We present the application of a deterministic logic BIST scheme on state-of-the-art industrial circuits. Experimental results show that complete fault coverage can be achieved for industrial circuits up to 100 K gates with 10000 test patterns, at a total area cost for BIST hardware of typically 5%-15%. It is demonstrated that a tradeoff is possible between test quality, test time, and silicon area. In contrast to BIST schemes based on test point insertion no modifications of the circuit under test are required, complete fault efficiency is guaranteed, and the impact on the design process is minimized.

/pdf/application-of-deterministic-logic-bist-on-industrial-43c4m51guf.pdf

Application of deterministic logic BIST on industrial circuits

A deterministic BIST scheme for circuits with multiple scan paths is presented. A procedure is described for synthesizing a pattern generator which stimulates all scan chains simultaneously and guarantees complete fault coverage. The new scheme may require less chip area than a classical LFSR-based approach while better or even complete fault coverage is obtained at the same time.

Deterministic BIST with multiple scan chains

A deterministic BIST scheme is presented which requires less hardware overhead than pseudo-random BIST but obtains better or even complete fault coverage at the same time. It takes advantage of the fact that any autonomous BIST scheme needs a BIST control unit for indicating the completion of the self-test at least. Hence, pattern counters and bit counters are always available, and they provide information to be used for deterministic pattern generation by some additional circuitry. This paper presents a systematic way for synthesizing a pattern generator which needs less area than a 32-bit LFSR for random pattern generation for all the benchmark circuits.

/pdf/using-bist-control-for-pattern-generation-earpuvl286.pdf

Using BIST control for pattern generation

A method, computer program and device for creating a viewing protocol for medical images is described. At least a first site of interest is identified in a medical imaging data set captured from the patient. Patient record data or computer assisted detection information can be used to identify the site of interest, which may be a potential lesion. A viewing protocol for displaying medical images to a user is planned. The viewing protocol includes a viewing path along which an image of the site of interest will be displayed. The viewing protocol also includes a trigger associated with the site of interest. When the trigger event is encountered the dynamic mode of image display is reconfigured to dynamically highlight the site of interest. The viewing protocol can then be used to control the display of images so as to provide, for example, a virtual endoscope.

Gundolf Kiefer

Papers

Bit-flipping BIST

Application of deterministic logic BIST on industrial circuits

Deterministic BIST with multiple scan chains

Using BIST control for pattern generation

Medical image viewing protocols