A phenomenological description, or “conceptual model,” of how direct-injection (DI) diesel combustion occurs has been derived from laser-sheet imaging and other recent optical data. To provide background, the most relevant of the recent imaging data of the author and co-workers are presented and discussed, as are the relationships between the various imaging measurements. Where appropriate, other supporting data from the literature is also discussed. Then, this combined information is summarized in a series of idealized schematics that depict the combustion process for a typical, modern-diesel-engine condition. The schematics incorporate virtually all of the information provided by our recent imaging data including: liquidand vapor-fuel zones, fuel/air mixing, autoignition, reaction zones, and soot distributions. By combining all these elements, the schematics show the evolution of a reacting diesel fuel jet from the start of fuel injection up through the first part of the mixing-controlled burn (i.e. until the end of fuel injection). In addition, for a “developed” reacting diesel fuel jet during the mixingcontrolled burn, the schematics explain the sequence of events that occurs as fuel moves from the injector downstream through the mixing, combustion, and emissions-formation processes. The conceptual model depicted in these schematics also gives insight into the most likely mechanisms for soot formation and destruction and NO formation during the portion of the DI diesel combustion event discussed.

A Conceptual Model of DI Diesel Combustion Based on Laser-Sheet Imaging*

Ambient gas density and fuel vaporization effects on the penetration and dispersion of diesel sprays were examined over a gas density range spanning nearly two order of magnitude. This range included gas densities more than a factor of two higher than top-dead-center conditions in current technology heavy-duty diesel engines. The results show that ambient gas density has a significantly larger effect on spray penetration and a smaller effect on spray dispersion than has been previously reported. The increased dependence of penetration on gas density is shown to be the result of gas density effects on dispersion. In addition, the results show that vaporization decreases penetration and dispersion by as much as 20% relative to non-vaporizing sprays; however, the effects of vaporization decrease with increasing gas density. Characteristic penetration time and length scales are presented that include a dispersion term that accounts for the increased dependence of penetration on ambient density. These penetration time and length scales collapse the penetration data obtained over the entire range of conditions examined in the experiment into two distinct non-dimensional penetration curves: one for the non-vaporizing conditions and one for the vaporizing conditions. Comparison of the two nondimensional penetration curves to a theoretical penetration correlation for non-vaporizing sprays helped isolate and explain the effects of droplets and vaporization on penetration. The theoretical penetration correlation was derived using the penetration time and length scales and simple model for a non-vaporizing spray that has been previously presented in the literature. The correlation is in good agreement with the non-vaporizing data from this experiment and other commonly quoted penetration data sets. It also provides a potential explanation for much of scatter in the penetration predicted by various correlations in the literature.

/pdf/effects-of-gas-density-and-vaporization-on-penetration-and-53r9byyd3t.pdf

Effects of Gas Density and Vaporization on Penetration and Dispersion of Diesel Sprays

Advanced compression-ignition (CI) engines can deliver both high efficiencies and very low NOX and particulate (PM) emissions. Efficiencies are comparable to conventional diesel engines, but unlike conventional diesel engines, the charge is highly dilute and premixed (or partially premixed) to achieve low emissions. Dilution is accomplished by operating either lean or with large amounts of EGR. The development of these advanced CI engines has evolved mainly along two lines. First, for fuels other than diesel, a combustion process commonly known as homogeneous charge compression-ignition (HCCI) is generally used, in which the charge is premixed before being compression ignited. Although termed “homogeneous,” there are always some thermal or mixture inhomogeneities in real HCCI engines, and it is sometimes desirable to introduce additional stratification. Second, for diesel fuel (which autoignites easily but has low volatility) an alternative low-temperature combustion (LTC) approach is used, in which the autoignition is closely coupled to the fuel-injection event to provide control over ignition timing. To obtain dilute LTC, this approach relies on high levels of EGR, and injection timing is typically shifted 10–15° CA earlier or later than for conventional diesel combustion so temperatures are lower, which delays ignition and provides more time for premixing. Although these advanced CI combustion modes have important advantages, there are difficulties to implementing them in practical engines. In this article, the principles of HCCI and diesel LTC engines are reviewed along with the results of research on the in-cylinder processes. This research has resulted in substantial progress toward overcoming the main challenges facing these engines, including: improving low-load combustion efficiency, increasing the high-load limit, understanding fuel effects, and maintaining low NOX and PM emissions over the operating range.

https://www.engr.colostate.edu/~marchese/combustion10/1.pdf

Advanced compression-ignition engines—understanding the in-cylinder processes

Scaling Liquid-Phase Fuel Penetration in Diesel Sprays Based on Mixing-Limited Vaporization

Liquid-Phase Fuel Penetration in Diesel Sprays

A new concept for low emission diesel combustion

The characteristics of diesel spray and flame in a quiescent atmosphere were studied as a function of injection pressure ranging from 30 to 110 MPa. Measurements included the spray form and Sauter mean diameter of a non-evaporating spray, the liquid phase penetration of an evaporating spray and the visualization of sooting zone in a flame. Experimental results show that high pressure injection improves the atomization and air entrainment of non-evaporating spray and that the liquid phase penetration of evaporating spray is hardly affected by injection pressure, demonstrating a promotion of evaporation with injection pressure. Visualization of the sooting zone in a flame made it clear that high pressure injection is advantageous in reducing soot formation and shortening the combustion duration.

Effect of High Pressure Injection on Soot Formation Processes in a Rapid Compression Machine to Simulate Diesel Flames

A new technique is developed for the in-situ measurement of Sauter mean diameter of droplets in non-evaporating transient dense sprays. This method analyzes the image of a shadowpicture of a spray based on the incident light extinction principle, and allows the sizing of Sauter mean diameter of whole droplets in a transient spray with any shape. In addition, this method allows the measurement of the local droplet size in a quasi-steady region of an axisymmetric spray if the conservation equations regarding mass and momentum are included in the calculation and data analysis. A calibration was carried out using glass beads as test particles: this was proved to have an accuracy of Sauter mean diameter measurement within 10%, on average. Applications of the new technique to both diesel and gasoline (EFI) sprays have been made. The experimental results show that the rise in injection pressure contributes in the reduction of the overall Sauter mean diameter and that, in the peripheral region the droplets are smaller than those in the central region.

Haruyuki Yokota

Papers

A new concept for low emission diesel combustion

Effect of High Pressure Injection on Soot Formation Processes in a Rapid Compression Machine to Simulate Diesel Flames

A New Technique for the Measurement of Sauter Mean Diameter of Droplets in Unsteady Dense Sprays

Fast Burning and Reduced Soot Formation via Ultra-High Pressure Diesel Fuel Injection

Development of Efficient Urea-SCR Systems for EPA 2010-Compliant Medium Duty Diesel Vehicles