Similar to the efforts to move toward electric vehicles, much research has focused on the idea of a more electric aircraft (MEA). The motivations for this research are similar to that for vehicles and include goals to reduce emissions and decrease fuel consumption. In traditional aircraft, multiple systems may use one type or a combination of types of energy, including electrical, hydraulic, mechanical, and pneumatic energy. However, all energy types have different drawbacks, including the sacrifice of total engine efficiency in the process of harvesting a particular energy, as with hydraulic and pneumatic systems. The goal for future aircraft is to replace most of the major systems currently utilizing nonelectric power, such as environmental controls and engine start, with new electrical systems to improve a variety of aircraft characteristics, such as efficiency, emissions, reliability, and maintenance costs. This paper provides an in-depth look into how the systems have—or will be—changed. Future aircraft capabilities such as electric taxi and gas–electric propulsion for aircraft are also included for discussion. Most recent commercial transport aircrafts are described as the current state-of-the-art electric aircraft system. Future goals, including those of NASA, are presented for future advances in MEA.

More Electric Aircraft: Review, Challenges, and Opportunities for Commercial Transport Aircraft

The constant growth of air traffic, the demand for performance optimization, and the need for decreasing both operating and maintenance costs have encouraged the aircraft industry to move toward more electric solutions. As a result of this trend, electric power required on-board of aircraft has significantly increased through the years, causing major changes in electric power system architectures. Considering this scenario, this paper gives a review about the evolution of electric power generation systems in aircraft. The major achievements are highlighted and the rationale behind some significant developments discussed. After a brief historical overview of the early dc generators (both wind- and engine-driven), the reasons which brought the definitive passage to the ac generation, for larger aircraft, are presented and explained. Several ac generation systems are investigated with particular attention being focused on the voltage levels and the generator technology. Furthermore, examples of commercial aircraft implementing ac generation systems are provided. Finally, the trends toward modern generation systems are also considered giving prominence to their challenges and feasibility.

/pdf/electrical-power-generation-in-aircraft-review-challenges-1fsf4e1o1k.pdf

Electrical Power Generation in Aircraft: Review, Challenges, and Opportunities

Electric, hybrid, and turboelectric fixed-wing aircraft: A review of concepts, models, and design approaches

Superconducting technology applications in electric machines have long been pursued due to their significant advantages of higher efficiency and power density over conventional technology. However, in spite of many successful technology demonstrations, commercial adoption has been slow, presumably because the threshold for value versus cost and technology risk has not yet been crossed. One likely path for disruptive superconducting technology in commercial products could be in applications where its advantages become key enablers for systems which are not practical with conventional technology. To help systems engineers assess the viability of such future solutions, we present a technology roadmap for superconducting machines. The timeline considered was ten years to attain a Technology Readiness Level of 6+, with systems demonstrated in a relevant environment. Future projections, by definition, are based on the judgment of specialists, and can be subjective. Attempts have been made to obtain input from a broad set of organizations for an inclusive opinion. This document was generated Superconductor Science and Technology Supercond. Sci. Technol. 30 (2017) 123002 (41pp) https://doi.org/10.1088/1361-6668/aa833e Original content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI. 0953-2048/17/123002+41$33.00 © 2017 IOP Publishing Ltd Printed in the UK 1 through a series of teleconferences and in-person meetings, including meetings at the 2015 IEEE PES General meeting in Denver, CO, the 2015 ECCE in Montreal, Canada, and a final workshop in April 2016 at the University of Illinois, Urbana-Champaign that brought together a broad group of technical experts spanning the industry, government and academia.

https://iopscience.iop.org/article/10.1088/1361-6668/aa833e/pdf

High power density superconducting rotating machines—development status and technology roadmap

Sustainability in the aviation industry calls for aircraft that are significantly quieter and more fuel efficient than today's fleet. Achieving this will require revolutionary new concepts, in particular, electric propulsion. Superconducting machines offer the only viable path to achieve the power densities needed in airborne applications. This paper outlines the main issues involved in using superconductors for aeropropulsion. We review our investigation of the feasibility of superconducting electric propulsion, which integrate for the first time, the multiple disciplines and areas of expertise needed to design electric aircraft. It is shown that superconductivity is clearly the enabling technology for the more efficient turbo-electric aircraft of the future.

Next Generation More-Electric Aircraft: A Potential Application for HTS Superconductors

A single-aisle commercial transport concept with a turboelectric propulsion system architecture was developed assuming entry into service in 2035 and compared to a similar technology conventional configuration. The turboelectric architecture consisted of two underwing turbofans with generators extracting power from the fan shaft and sending it to a rear fuselage, axisymmetric, boundary layer ingesting fan. Results indicate that the turbo- electric concept has an economic mission fuel burn reduction of 7%, and a design mission fuel burn reduction of 12% compared to the conventional configuration. An exploration of the design space was performed to better understand how the turboelectric architecture changes the design space, and system sensitivities were run to determine the sensitivity of thrust specific fuel consumption at top of climb and propulsion system weight to the motor power, fan pressure ratio, and electrical transmission efficiency of the aft boundary layer ingesting fan.

/pdf/conceptual-design-of-a-single-aisle-turboelectric-commercial-xf16wju7r6.pdf

Conceptual Design of a Single-Aisle Turboelectric Commercial Transport With Fuselage Boundary Layer Ingestion

Meeting NASA's N+3 goals requires a fundamental shift in approach to aircraft and engine design. Material and design improvements allow higher pressure and higher temperature core engines which improve the thermal efficiency. Propulsive efficiency, the other half of the overall efficiency equation, however, is largely determined by the fan pressure ratio (FPR). Lower FPR increases propulsive efficiency, but also dramatically reduces fan shaft speed through the combination of larger diameter fans and reduced fan tip speed limits. The result is that below an FPR of 1.5 the maximum fan shaft speed makes direct drive turbines problematic. However, it is the low pressure ratio fans that allow the improvement in propulsive efficiency which, along with improvements in thermal efficiency in the core, contributes strongly to meeting the N+3 goals for fuel burn reduction. The lower fan exhaust velocities resulting from lower FPRs are also key to meeting the aircraft noise goals. Adding a gear box to the standard turbofan engine allows acceptable turbine speeds to be maintained. However, development of a 50,000+ hp gearbox required by fans in a large twin engine transport aircraft presents an extreme technical challenge, therefore another approach is needed. This paper presents a propulsion system which transmits power from the turbine to the fan electrically rather than mechanically. Recent and anticipated advances in high temperature superconducting generators, motors, and power lines offer the possibility that such devices can be used to transmit turbine power in aircraft without an excessive weight penalty. Moving to such a power transmission system does more than provide better matching between fan and turbine shaft speeds. The relative ease with which electrical power can be distributed throughout the aircraft opens up numerous other possibilities for new aircraft and propulsion configurations and modes of operation. This paper discusses a number of these new possibilities. The Boeing N2 hybrid-wing-body (HWB) is used as a baseline aircraft for this study. The two pylon mounted conventional turbofans are replaced by two wing-tip mounted turboshaft engines, each driving a superconducting generator. Both generators feed a common electrical bus which distributes power to an array of superconducting motor-driven fans in a continuous nacelle centered along the trailing edge of the upper surface of the wing-body. A key finding was that traditional inlet performance methodology has to be modified when most of the air entering the inlet is boundary layer air. A very thorough and detailed propulsion/airframe integration (PAI) analysis is required at the very beginning of the design process since embedded engine inlet performance must be based on conditions at the inlet lip rather than freestream conditions. Examination of a range of fan pressure ratios yielded a minimum Thrust-specific-fuel-consumption (TSFC) at the aerodynamic design point of the vehicle (31,000 ft /Mach 0.8) between 1.3 and 1.35 FPR. We deduced that this was due to the higher pressure losses prior to the fan inlet as well as higher losses in the 2-D inlets and nozzles. This FPR is likely to be higher than the FPR that yields a minimum TSFC in a pylon mounted engine. 1

/pdf/turboelectric-distributed-propulsion-engine-cycle-analysis-7up1rf7ovc.pdf

Turboelectric Distributed Propulsion Engine Cycle Analysis for Hybrid-Wing-Body Aircraft

NASA is investing in Electrified Aircraft Propulsion (EAP) research as part of the portfolio to improve the fuel efficiency, emissions, and noise levels in commercial transport aircraft. Turboelectric, partially turboelectric, and hybrid electric propulsion systems are the primary EAP configurations being evaluated for regional jet and larger aircraft. The goal is to show that one or more viable EAP concepts exist for narrow body aircraft and mature tall-pole technologies related to those concepts. A summary of the aircraft system studies, technology development, and facility development is provided. The leading concept for mid-term (2035) introduction of EAP for a single aisle aircraft is a tube and wing, partially turbo electric configuration (STARC-ABL), however other viable configurations exist. Investments are being made to raise the TRL level of light weight, high efficiency motors, generators, and electrical power distribution systems as well as to define the optimal turbine and boundary layer ingestion systems for a mid-term tube and wing configuration. An electric aircraft power system test facility (NEAT) is under construction at NASA Glenn and an electric aircraft control system test facility (HEIST) is under construction at NASA Armstrong. The correct building blocks are in place to have a viable, large plane EAP configuration tested by 2025 leading to entry into service in 2035 if the community chooses to pursue that goal.

/pdf/overview-of-nasa-electrified-aircraft-propulsion-research-2p0bfcj6hi.pdf

Overview of NASA Electrified Aircraft Propulsion Research for Large Subsonic Transports

/pdf/turboelectric-distributed-propulsion-engine-cycle-analysis-1o512c5sut.pdf

The performance of the N3-X, a 300 passenger hybrid wing body (HWB) aircraft with turboelectric distributed propulsion (TeDP), has been analyzed to see if it can meet the 70% fuel burn reduction goal of the NASA Subsonic Fixed Wing project for N+3 generation aircraft. The TeDP system utilizes superconducting electric generators, motors and transmission lines to allow the power producing and thrust producing portions of the system to be widely separated. It also allows a small number of large turboshaft engines to drive any number of propulsors. On the N3-X these new degrees of freedom were used to (1) place two large turboshaft engines driving generators in freestream conditions to maximize thermal efficiency and (2) to embed a broad continuous array of 15 motor driven propulsors on the upper surface of the aircraft near the trailing edge. That location maximizes the amount of the boundary layer ingested and thus maximizes propulsive efficiency. The Boeing B777-200LR flying 7500 nm (13890 km) with a cruise speed of Mach 0.84 and an 118100 lb payload was selected as the reference aircraft and mission for this study. In order to distinguish between improvements due to technology and aircraft configuration changes from those due to the propulsion configuration changes, an intermediate configuration was included in this study. In this configuration a pylon mounted, ultra high bypass (UHB) geared turbofan engine with identical propulsion technology was integrated into the same hybrid wing body airframe. That aircraft achieved a 52% reduction in mission fuel burn relative to the reference aircraft. The N3-X was able to achieve a reduction of 70% and 72% (depending on the cooling system) relative to the reference aircraft. The additional 18% - 20% reduction in the mission fuel burn can therefore be attributed to the additional degrees of freedom in the propulsion system configuration afforded by the TeDP system that eliminates nacelle and pylon drag, maximizes boundary layer ingestion (BLI) to reduce inlet drag on the propulsion system, and reduces the wake drag of the vehicle.

https://ntrs.nasa.gov/api/citations/20120000856/downloads/20120000856.pdf

James L. Felder

Papers

Conceptual Design of a Single-Aisle Turboelectric Commercial Transport With Fuselage Boundary Layer Ingestion

Turboelectric Distributed Propulsion Engine Cycle Analysis for Hybrid-Wing-Body Aircraft

Overview of NASA Electrified Aircraft Propulsion Research for Large Subsonic Transports

Turboelectric Distributed Propulsion Engine Cycle Analysis for Hybrid-Wing-Body Aircraft

Turboelectric Distributed Propulsion in a Hybrid Wing Body Aircraft