다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

Additive manufacturing of metallic components – Process, structure and properties

A fast-Fourier-transform method of topography and interferometry is proposed. By computer processing of a noncontour type of fringe pattern, automatic discrimination is achieved between elevation and depression of the object or wave-front form, which has not been possible by the fringe-contour-generation techniques. The method has advantages over moire topography and conventional fringe-contour interferometry in both accuracy and sensitivity. Unlike fringe-scanning techniques, the method is easy to apply because it uses no moving components.

Fourier-transform method of fringe-pattern analysis for computer-based topography and interferometry

This chapter discusses leading problems linked to energy that the world is now confronting and to propose some ideas concerning possible solutions. Oil deserves special attention among all energy sources. Since the beginning of 1981, it has merely been continuing and enhancing the downward movement in consumption and prices caused by excessive rises, especially for light crudes such as those from Africa, and the slowing down of worldwide economic growth. Densely-populated oil-producing countries need to produce to live, to pay for their food and their equipment. If the economic growth of the industrialized countries were to be 4%, even if investment in the rational use of energy were pushed to the limit and the development of nonpetroleum energy sources were also pursued actively, it would be extremely difficult to prevent a sharp rise in prices. It is evident that it is absolutely necessary to pursue actively the development of coal, natural gas, and nuclear power if a physical shortage of energy is not to block economic growth.

World energy outlook

Additive manufacturing (AM) alias 3D printing translates computer-aided design (CAD) virtual 3D models into physical objects. By digital slicing of CAD, 3D scan, or tomography data, AM builds objects layer by layer without the need for molds or machining. AM enables decentralized fabrication of customized objects on demand by exploiting digital information storage and retrieval via the Internet. The ongoing transition from rapid prototyping to rapid manufacturing prompts new challenges for mechanical engineers and materials scientists alike. Because polymers are by far the most utilized class of materials for AM, this Review focuses on polymer processing and the development of polymers and advanced polymer systems specifically for AM. AM techniques covered include vat photopolymerization (stereolithography), powder bed fusion (SLS), material and binder jetting (inkjet and aerosol 3D printing), sheet lamination (LOM), extrusion (FDM, 3D dispensing, 3D fiber deposition, and 3D plotting), and 3D bioprinting....

Polymers for 3D Printing and Customized Additive Manufacturing

Model based learning for efficient modelling of heat transfer dynamics

Model to Optimise the Grain Pattern of Grinding Discs with Controlled Positions of the Abrasives

The final part density in laser powder bed fusion is influenced by the powder particle size distribution. Too fine powders are not spreadable, and too coarse powders cause porosity. Powder blends, especially bimodal ones, can exhibit higher packing densities and changes in flowability compared to their monomodal constituents. These properties can influence final part density. Therefore, the influence of bimodal powder on final part density was investigated. Two gas atomized 316L (1.4404) powders with a D50 of 20.3 µm and 60.3 µm were blended at weight ratios of 3:1, 1:1, and 1:3, and the original and blended powders were processed. The results show that the final part porosity increases almost linearly with an increasing volume fraction of coarse powder. Furthermore, the final part density is independent of powder bulk density and flowability. Measurements of the top surface show that an increase of part porosity by coarse powder is caused by an increase in melt pool fluctuation, which in turn causes irregular solidified scan tracks. Additionally, the results show that the powder segregation during coating is stronger for the bimodal powder; however, no influence of the segregation on the part density could be found.

/pdf/effect-of-bimodal-powder-blends-on-part-density-and-melt-4mr6s202mo.pdf

Effect of bimodal powder blends on part density and melt pool fluctuation in laser powder bed fusion

Selective Laser Melting (SLM) is capable producing high performance parts e.g. for the aerospace or turbine industry. Nonetheless there is a high potential in other sectors such as in the electronic industry. For these applications, optimal properties of magnetic flux, coercive force and hysteresis are required. An isotropic microstructure is favoured a condition hardly achieved by the SLM process. The SLM-processing window for a NiFe14Cu5Mo4 alloy is developed and basic microstructure is presented. The electro-magnetic properties are measured using a specific test bench allowing a direct comparison of the properties with a reference material. The results are discussed with a specific focus on the effect of the microstructure on the industrial usage.

Konrad Wegener

Papers

Model based learning for efficient modelling of heat transfer dynamics

Model to Optimise the Grain Pattern of Grinding Discs with Controlled Positions of the Abrasives

Effect of bimodal powder blends on part density and melt pool fluctuation in laser powder bed fusion

Microstructure and Electro-Magnetic Properties of a Nickel-Based Anti-Magnetic Shielding Alloy

Geometry Optimisation for 2D Cutting: A Quadratic Programming Approach