Recent progress in aluminum metal matrix composites: A review on processing, mechanical and wear properties

The series of books represents a thorough treatment of ultra-high temperature materials with melting (sublimation or decomposition) points around or over 2500 °C. In the third volume are included physical (structural, thermal, electromagnetic, optical, mechanical, nuclear) and chemical (more than 1100 binary, ternary and multi-component systems, including those used for materials design, data on solid-state diffusion, wettability, interaction with chemicals, gases and aqueous solutions) properties of titanium monocarbide TiC1–x, vanadium monocarbide VC1–x and related 2D-molecular (graphene-like) carbide MXenes, discovered and developed only in the last decade. TiC1–x and VC1–x are also widely applied in the general technological and engineering practice in a wide range of temperatures as parts of highly hard materials (alloys) and special steels. This book will be of interest to researchers, engineers, postgraduate, graduate and undergraduate students alike. For the named materials, readers/users are provided with the full qualitative and quantitative assessment, which is based on the latest updates in the field of fundamental physics, chemistry, nanotechnology, materials science, design and engineering.

http://link.springer.com/content/pdf/10.1007/978-94-024-2039-5.pdf

Ultra-High Temperature Materials III: Refractory Carbides II (Ti and V Carbides)

The microstructure of graphite flake (GF) reinforced aluminum (Al) matrix (Al–GF) composites was observed in detail. Due to thermal mismatch between Al and GF, an inner structure of GF was damaged in proximity to the Al/GF interface, while the unique bridging of the sticky graphite sheets barely connected the Al matrix and GF. This result suggests that the GF interlaminar strength is weaker than the Al/GF interfacial strength; the GF interlaminar strength is thus the dominant determinant of the thermomechanical and mechanical properties of the Al–GF composite. Whereas the thermal conductivity of the Al–GF composite was consistent with that theoretically predicted, the outstanding thermal expansion coefficient (TEC) of the graphite was not reflected in the produced Al–GF composites. The damaged inner structure of GF in proximity to the Al/GF interface contributes to heat transfer but does not bear the load resulting from thermal stress.

/pdf/interfacial-microstructure-of-graphite-flake-reinforced-7u7g9623gn.pdf

Interfacial microstructure of graphite flake reinforced aluminum matrix composites fabricated via hot pressing

In this research, the mechanical properties and microstructure of Al-15 wt % TiC composite samples prepared by spark plasma, microwave, and conventional sintering were investigated. The sintering process was performed by the speak plasma sintering (SPS) technique, microwave and conventional furnaces at 400 °C, 600 °C, and 700 °C, respectively. The results showed that sintered samples by SPS have the highest relative density (99% of theoretical density), bending strength (291 ± 12 MPa), and hardness (253 ± 23 HV). The X-ray diffraction (XRD) investigations showed the formation of TiO2 from the surface layer decomposition of TiC particles. Scanning electron microscopy (SEM) micrographs demonstrated uniform distribution of reinforcement particles in all sintered samples. The SEM/EDS analysis revealed the formation of TiO2 around the porous TiC particles.

https://www.mdpi.com/1996-1944/10/11/1255/pdf

Evaluation of Microstructure and Mechanical Properties of Al-TiC Metal Matrix Composite Prepared by Conventional, Microwave and Spark Plasma Sintering Methods.

The use of metal matrix composites (MMCs) in a variety of products is significantly increasing with time due to the fact that their properties can be tailored and designed to suit specific applications. However, the future usage of MMC products is very much dependent on their beneficial aspects and hence it is critical to ensure in a robust repeatable manner the superior physical property advantages compared to conventional unreinforced monolithic metal counterparts. Although numerous routes are available for production of MMC products, each of them has their own advantages and disadvantages. This article provides an overview of advanced production routes for MMCs. The discussion also highlights challenges and presents a future prospectus for MMCs. Powder metallurgy and casting routes are still extensively used for production of MMCs. Aluminum alloys are today the most commonly used matrix materials in MMC products. Carbides (eg, SiC, TiC, and B4C), carbon allotropes (eg, CNTs and graphene), and alumina (Al2O3) are currently the most used reinforcement materials. Nevertheless, the use of nano and of hybrid reinforcements are seeing increased usage in niche applications. Additive manufacturing (AM) is discussed as a novel production route for MMC products. This process represents a promising method for the production of MMC products.

https://onlinelibrary.wiley.com/doi/pdf/10.1002/eng2.12330

Advanced production routes for metal matrix composites

A metal matrix composite has been obtained by a novel synthesis route, reacting Al 3 Ti and graphite at 1000 °C for about 1 min after ball-milling and compaction. The resulting composite is made of an aluminium matrix reinforced by nanometer sized TiC particles (average diameter 70 nm). The average TiC/Al ratio is 34.6 wt.% (22.3 vol.%). The microstructure consists of an intimate mixture of two domains, an unreinforced domain made of the Al solid solution with a low TiC reinforcement content, and a reinforced domain. This composite exhibits uncommon mechanical properties with regard to previous micrometer sized Al–TiC composites and to its high reinforcement volume fraction, with a Young’s modulus of ∼110 GPa, an ultimate tensile strength of about 500 MPa and a maximum elongation of 6%.

/pdf/microstructure-and-mechanical-properties-of-an-al-tic-metal-54elxcc8m8.pdf

Laurent Chaffron

Papers

Microstructure and mechanical properties of an Al–TiC metal matrix composite obtained by reactive synthesis