The Super-X Divertor (SXD), a robust axisymmetric redesign of the divertor magnetic geometry that can allow a fivefold increase in the core power density of toroidal fusion devices, is presented. With small changes in poloidal coils and currents for standard divertors, the SXD allows the largest divertor plate radius inside toroidal field coils. This increases the plasma-wetted area by 2–3 times over all flux-expansion-only methods (e.g., plate near main X point, plate tilting, X divertor, and snowflake), decreases parallel heat flux and hence plasma temperature at plate, and increases connection length by 2–5 times. Examples of high-power-density fusion devices enabled by SXD are discussed; the most promising near-term device is a 100 MW modular compact fusion neutron source “battery” small enough to fit inside a conventional fission blanket.

/pdf/super-x-divertors-and-high-power-density-fusion-devices-2ythxgxyn1.pdf

Super-X divertors and high power density fusion devices

The limited thermal power handling capacity of the standard divertors (used in current as well as projected tokamaks) is likely to force extremely high (∼90%) radiation fractions frad in tokamak fusion reactors that have heating powers considerably larger than ITER [D. J. Campbell, Phys. Plasmas 8, 2041 (2001)]. Such enormous values of necessary frad could have serious and debilitating consequences on the core confinement, stability, and dependability for a fusion power reactor, especially in reactors with Internal Transport Barriers. A new class of divertors, called X-divertors (XD), which considerably enhance the divertor thermal capacity through a flaring of the field lines only near the divertor plates, may be necessary and sufficient to overcome these problems and lead to a dependable fusion power reactor with acceptable economics. X-divertors will lower the bar on the necessary confinement to bring it in the range of the present experimental results. Its ability to reduce the radiative burden impart...

On heat loading, novel divertors, and fusion reactors

This paper presents results of conceptual design activities and associated RD neutronics experiments and analyses; and development of the blanket module fabrication technology. Upon developing the fabrication technology for the first wall and box structure, a hot isostatic pressing bonded F82H first wall mock-up with embedded rectangular cooling channels was successfully fabricated. It withstood the high heat flux test at 2.7 MW m−2. Also, a correlation parameter of the Li2TiO3 pebble bed made by the sol–gel method was verified by measurement of the thermal conductivity of the breeder pebble bed, which is one of the most important design data.

/pdf/design-and-technology-development-of-solid-breeder-blanket-5fz16zuv2n.pdf

Design and technology development of solid breeder blanket cooled by supercritical water in Japan

http://ralphmoir.com/media/kotschFusFis.pdf

Fusion-Fission Transmutation Scheme—Efficient destruction of nuclear waste

The concept for a compact DEMO reactor named 'SlimCS' is presented. Distinctive features of the concept are low aspect ratio (A = 2.6) and use of a reduced-size centre solenoid (CS) which has the function of plasma shaping rather than poloidal flux supply. The reduced-size CS enables us to introduce a thin toroidal field coil system which contributes to reducing the weight and perhaps lessening the construction cost. Low-A has merits of vertical stability for high elongation (κ) and high normalized beta (βN), which leads to a high power density with reasonable physics requirements. This is because high κ facilitates high nGW (because of an increase in Ip), which allows efficient use of the capacity of high βN. From an engineering aspect, low-A may ensure ease in designing blanket modules robust to electromagnetic forces acting on disruptions. Thus, a superconducting low-A tokamak reactor such as SlimCS can be a promising DEMO concept with physics and engineering advantages.

http://iopscience.iop.org/article/10.1088/0029-5515/47/8/022/pdf

SlimCS—compact low aspect ratio DEMO reactor with reduced-size central solenoid

The compact reversed shear tokamak CREST is a cost competitive reactor concept based on a reversed shear high β plasma and water cooled ferritic steel components. The moderate aspect ratio A = 3.4 and the elongation κ = 2.0 of CREST are very similar to the case of the ITER advanced mode plasma. Presentation of such a concept based on the ITER project should be worth while for formulating a fusion development strategy. The achievement of a competitive cost of electricity (COE) is the first priority for electric power industries. High β and high thermal efficiency are the most effective parameters for achieving a competitive COE. In order to achieve a high efficiency power plant, a superheated steam cycle has been adopted which permits a high thermal efficiency (η = 41%). Current profile control and high speed plasma rotation by neutral beam current drive stabilize the ideal MHD activity up to the Troyon coefficient βN = 5.5. A cost assessment has shown that CREST could generate about 1.16 GW(e) electric power at a competitive cost.

https://iopscience.iop.org/article/10.1088/0029-5515/40/3Y/326/pdf

M. Takemoto

Papers

Compact reversed shear tokamak reactor with a superheated steam cycle