An industrial technology for semi-continuous casting of large-sized ingots from wrought aluminum alloy 1580 has been developed through the use of complex modeling, including computer modeling and physical modeling. The ProCAST and ANSYS software packages equipped with the FLUENT module were used for computer modeling. The physical modeling was carried out on a laboratory semi-continuous casting unit (SCCU), which represents a tenfold reduced physical model of an industrial casting unit for the vertical semi-continuous casting of ingots from aluminum alloys. An aluminum-magnesium alloy with the addition of 0.05% (wt.) of scandium was used as the object of modeling. The results of computer modeling were tested at the SCCU, and then computer modeling was carried out for casting a large ingot. According to the modes obtained in the simulation, an ingot with a section of 1310 × 560 mm was cast under industrial conditions, which had a good surface quality with the absence of casting defects. In the microstructure of an industrial ingot and an ingot cast on the SCCU, there were no primary intermetallic compounds Al3(Sc, Zr), which makes it possible to strengthen the alloy upon annealing. To check the manufacturability during rolling, billets with a size of 40 × 120 × 170 mm were cut from these ingots, which were hot-rolled to a thickness of 5 mm, and then cold rolled to a thickness of 1 mm. The rolling results revealed good workability of the alloy, which was reflected in the high quality of the surface and the absence of cracks at the edges of the rolled stock. The mechanical properties of sheets obtained from both ingots were at the same level, which proves the reliability of casting modes for ingots obtained by complex modeling and the validity of their use for industrial conditions of the semi-continuous casting of large ingots from aluminum alloys. 

/pdf/modeling-of-casting-technology-of-large-sized-ingots-from-2hcypdit.pdf

Modeling of casting technology of large-sized ingots from deformable aluminum alloys

Based on the results achieved in systematic studies of structure formation and the formation of multicomponent phases, a scandium-containing filler metal from system alloy Mg-Zr-Nd for welding of aircraft casting was developed. The influence of scandium in magnesium filler alloy on its mechanical and special properties, such as long-term strength at elevated temperatures, was studied by the authors. It is established that modification of the magnesium alloy with scandium in an amount between 0.05 and 0.07% allows a fine-grained structure to be obtained, which increases its plasticity up to 70% and heat resistance up to 1.8 times due to the formation of complex intermetallic phases and the microalloying of the solid solution. Welding of the aircraft castings made of magnesium alloy with scandium-containing filler material allows obtaining a weld with a dense homogeneous fusion zone and the surrounding area without any defects. The developed filler material for welding surface defects (cracks, chips, etc.) formed during operation on aircraft engine bodies makes it possible to restore cast body parts and reuse them. The proposed filler material composition with an improved set of properties for the welding of body castings from Mg-Zr-Nd system alloy for aircraft engines makes it possible to increase their reliability and durability in general, extend the service life of aircraft engines, and obtain a significant economic effect.

https://www.mdpi.com/1996-1944/15/12/4213/pdf?version=1655195645

Casting Welding from Magnesium Alloy Using Filler Materials That Contain Scandium

Electronic structure and atomic migration of the fourth, fifth, and sixth period atoms in aluminum alloys: First principles calculation

Investigations of the rolling modes of plates from an experimental aluminum-magnesium alloy with a scandium content of 0.10–0.11 wt.%, corresponding to the chemical composition of the 1580 alloy, were carried out in laboratory and industrial conditions. It has been found that alloying of this material with scandium within the indicated limits leads to a significant grain refinement in the cast ingot and an increase in the strength properties of deformed semi-finished products. Based on the results of physical modeling of the rolling process, rational reduction modes are proposed, which made it possible to obtain deformed semi-finished products with the required level of mechanical properties. Based on the results of physical and computer modeling of the rolling process, rational reduction modes are proposed for pilot studies, which made it possible to obtain deformed semi-finished products with the required level of mechanical properties. At the same time, the power parameters of rolling did not exceed the allowable values of the force and rolling moment for the QUARTO 2800 rolling mill. To assess the formation patterns of the metal structure necessary to obtain high-quality plates, a metallographic analysis of the structure of cast and deformed semi-finished products from an experimental alloy was carried out. The results were used to test the reduction modes during sheet rolling and to adjust the casting parameters of experimental ingots. Annealing has practically no effect on the level of mechanical properties of plates obtained under production conditions in a hot-deformed state, while the ultimate tensile strength in the longitudinal direction is 388–389 MPa, the yield strength is 245–247 MPa, and the elongation to failure is 18.0–18.8%. After cold rolling, the plates have the following mechanical properties: ultimate tensile strength 413–414 MPa, yield strength 386–372 MPa, and elongation to failure 5.2–6.6%. Based on the results of the research, recommendations were formulated for the development and implementation of an industrial technology for rolling plates from alloy 1580 with a thickness of 31.5–45 mm from ingots with a thickness of 300–450 mm. 

/pdf/investigation-of-rolling-modes-structure-and-properties-of-602z3ztp.pdf

Investigation of rolling modes, structure, and properties of aluminum-magnesium alloy plates with a reduced scandium content

Investigation of Industrial 1580 Alloy Sheet Weldability by Friction Stir Welding

The structure and mechanical properties of an alloy of the aluminum-magnesium system with a scandium content of no more than 0.1% (wt.) (experimental alloy) at the stages of obtaining sheet semi-finished products have been investigated. The macro and micro structure of cast, hot, and cold rolled sheet semi-finished products has been studied by the methods of light and diffraction transmission electron microscopy, and their mechanical properties have been tested. Casting of ingots, hot, and cold rolling of the alloy was carried out in the conditions of a metallurgical enterprise. The section of the ingots was a rectangle 300 × 1460 mm in size. Preparation of ingots for rolling included milling of all surfaces and two-stage annealing at temperatures of 350 °C (first stage) and 425 °C (second stage). Rolling was carried out across the casting direction. For hot rolling, the billets were heated to 400–410 °C and carried out on a reversible hot rolling mill of grade quart with a roll barrel length of 2800 mm to a thickness of 8.2–9.2 mm. Then, the strips were rolled into rolls and annealed according to the following regime: temperature 390–400 °С, holding for 1 h, cooling with a furnace to 250–270 °С, and unloading into air. Cold rolling was carried out on a QUARTO mill of the CRM grade with a roll barrel length of 2800 mm to a thickness of 5.9–6.3 mm. Microstructural analysis was performed on a Carl Zeiss Axio Observer A1m light microscope using the AxioVision software package. The fine structure of semi-finished products was studied using Tecnai 30 G2 and JEM-2100 EX transmission electron microscopes. The chemical composition of dispersed particles of the secondary phases was determined using energy dispersive X-ray microanalysis (EDX) of thin foils in transmission using an INCA x-sight attachment. It is shown that alloying the experimental alloy with small additions of scandium, zirconium, and manganese leads to the formation of a supersaturated solid solution in the ingot. And upon annealing of the ingot and subsequent hot and cold rolling, a subgrain structure with inclusions of Al6Mn and Al3(Sc, Zr) phases of distribution density is formed in the alloy structure, explaining dispersion and structural hardening of sheet semi-finished products. It was found that the mechanical properties of cold-rolled sheets from the experimental alloy significantly exceed the properties of alloy 5083 with the same magnesium content. But without scandium and are approximately on the same level with alloy 1570 in which the scandium content in comparison with the experimental alloy is three times higher.

Maksim Yurievich Murashkin

Papers

Investigation the structure in cast and deformed states of aluminum alloy, economically alloyed with scandium and zirconium