Recent advances in all-solid-state rechargeable lithium batteries

Impedance networks cover the entire of electric power conversion from dc (converter, rectifier), ac (inverter), to phase and frequency conversion (ac-ac) in a wide range of applications. Various converter topologies have been reported in the literature to overcome the limitations and problems of the traditional voltage source, current source as well as various classical buck-boost, unidirectional, and bidirectional converter topologies. Proper implementation of the impedance-source network with appropriate switching configurations and topologies reduces the number of power conversion stages in the system power chain, which may improve the reliability and performance of the power system. The first part of this paper provides a comprehensive review of the various impedance-source-networks-based power converters and discusses the main topologies from an application point of view. This review paper is the first of its kind with the aim of providing a “one-stop” information source and a selection guide on impedance-source networks for power conversion for researchers, designers, and application engineers. A comprehensive review of various modeling, control, and modulation techniques for the impedance-source converters/inverters will be presented in Part II.

Impedance-Source Networks for Electric Power Conversion Part I: A Topological Review

This paper presents first an overview of the well-known voltage and current dc-link converter topologies used to implement a three-phase PWM ac-ac converter system. Starting from the voltage source inverter and the current source rectifier, the basics of space vector modulation are summarized. Based on that, the topology of the indirect matrix converter (IMC) and its modulation are gradually developed from a voltage dc-link back-to-back converter by omitting the dc-link capacitor. In the next step, the topology of the conventional (direct) matrix converter (CMC) is introduced, and the relationship between the IMC and the CMCs is discussed in a figurative manner by investigating the switching states. Subsequently, three-phase ac-ac buck-type chopper circuits are considered as a special case of matrix converters (MCs), and a summary of extended MC topologies is provided, including three-level and hybrid MCs. Therewith, a common knowledge basis of the individual converter topologies is established.

Review of Three-Phase PWM AC–AC Converter Topologies

This paper extends the impedance-source (Z-source) inverters concept to the transformer-based Z-source (trans-Z-source) inverters. The original Z-source inverter (ZSI) employs an impedance network of two inductors and two capacitors connected in a special arrangement to interface the dc source and the inverter bridge. It has buck and boost function that cannot be achieved by traditional voltage-source inverters and current-source inverters. In the proposed four trans-Z-source inverters, all the impedance networks consist of a transformer and one capacitor. While maintaining the main features of the previously presented Z-source network, the new networks exhibit some unique advantages, such as the increased voltage gain and reduced voltage stress in the voltage-fed trans-ZSIs and the expanded motoring operation range in the current-fed trans-ZSIs, when the turns ratio of the transformer windings is over 1. Simulation and experimental results of the voltage-fed and the current-fed trans-ZSIs are provided to verify the analysis.

Trans-Z-Source Inverters

Wavelet transform based on inner product in fault diagnosis of rotating machinery: A review

This paper presents different topologies of voltage inverters with alternative input LC networks. The basic topology is known in the literature as a Z-source inverter (ZSI). Alternative passive networks were named by the authors as T-sources. T-source inverter has fewer reactive components in comparison to conventional Z-source inverter. The most significant advantage of the T-source inverter (TSI) is its use of a common voltage source of the passive arrangement. Experimental results for the TSI are in agreement with theoretical and simulated prediction.

New type T-Source inverter

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed.

Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network

Z-source inverters are suited for applications which require a large range of gain, such as in renewable energy. Recently proposed Trans-Z-source inverters (TZSIs) and T-source inverters (TSIs) characterize improved voltage gain thanks to the application of coupled inductors with turns ratio higher than one. The present paper extends the concept of Trans-Z-source (T-source) inverters. Two novel impedance networks: the LCCT (inductor-capacitor-capacitor-transformer) Z-source impedance network and the LCCT-qZ-source impedance network are presented. The former contains two built-in DC-current-blocking capacitors connected in series with transformer windings and therefore prevent the transformer core from saturation while the latter contains one built-in DC-current-blocking capacitor and combines the features of qZ-source and T-source impedance networks. The novel topologies of LCCT-impedance-source inverters: LCCT-Z-source inverter (LCCT-ZSI) and LCCT-quasi-Z-source inverter (LCCT-qZSI) proposed in the paper characterize available continuous input current which is the advantage compared to TZSIs and TSIs. Simulations and experimental results are provided to verify the analysis of two proposed topologies.

New type LCCT-Z-source inverters

Many renewable generation units (e.g. PVs, fuel cells, small wind turbines) require integrated DC-AC converters providing efficient high step-up power conversion. On the basis of recent developments in impedance source (Z-source) inverters the present paper proposes an integration of quasi-Z-source inverter (qZSI) with a built-in high frequency transformer. Two new type LCCT-Z-Source inverters are presented by author. Proposed inverters characterize continuous input current, improved relationship between boost coefficient and modulation index and improved EMI performance. Application of four element (Inductor — Capacitor — Capacitor — Transformer) LCCT impedance network provides higher voltage gain than obtained in quasi-Z-source inverter. The advantage of proposed topology over other recently developed trans Z-source inverters (TZSI) is that two built-in capacitors block DC currents in transformer windings and prevents core saturation. Simulation and experimental results are shown to verify the proposed topologies.

LCCT-Z-Source inverters

Advanced control systems combined with high speed gate driver circuits enable extremely high rate of change of power devices voltages, up to hundreds of kV/us. Short rise times of power devices could cause significant EMC problems, which are unacceptable in majority of power electronics applications. It is known that voltage variations during diode switch-off depend on how long it takes for the charge stored near the p-n junction to be recovered during voltage reversing. In fast switching applications good forward recovery characteristics are needed. The silicon carbide (SiC) diodes characterize almost zero reverse recovery charge. However the lossless operation in connection with extremely high dv/dt could cause the SiC diodes less effective in damping the voltage ringing. The compromise between high efficiency and low EMI emission is therefore the actual aim of the research. The paper compares the static and dynamic characteristics of ultra fast silicon (Si) and SiC Schottky diodes and presents the study of the mechanism of parasitic high frequency oscillations during turn-off transient.

Marek Adamowicz

Papers

New type T-Source inverter

Step-Up DC/DC Converters With Cascaded Quasi-Z-Source Network

New type LCCT-Z-source inverters

LCCT-Z-Source inverters

Performance comparison of SiC Schottky diodes and silicon ultra fast recovery diodes