Showing papers by "Michael Stadermann published in 2006"
TL;DR: Gas and water flow measurements through microfabricated membranes in which aligned carbon nanotubes with diameters of less than 2 nanometers serve as pores enable fundamental studies of mass transport in confined environments, as well as more energy-efficient nanoscale filtration.
Abstract: We report gas and water flow measurements through microfabricated membranes in which aligned carbon nanotubes with diameters of less than 2 nanometers serve as pores. The measured gas flow exceeds predictions of the Knudsen diffusion model by more than an order of magnitude. The measured water flow exceeds values calculated from continuum hydrodynamics models by more than three orders of magnitude and is comparable to flow rates extrapolated from molecular dynamics simulations. The gas and water permeabilities of these nanotube-based membranes are several orders of magnitude higher than those of commercial polycarbonate membranes, despite having pore sizes an order of magnitude smaller. These membranes enable fundamental studies of mass transport in confined environments, as well as more energy-efficient nanoscale filtration.
2,637 citations
TL;DR: This report presents the first integration of single-wall carbon nanotubes (SWNTs) as a stationary phase into 100 mum x 100 mum square and 50-cm-long microfabricated channels and demonstrates highly reproducible separations of four-compound test mixtures on these columns in less than 1 s using fast temperature programming.
Abstract: The key to rapid temperature programmed separations with gas chromatography are a fast, low-volume injection and a short microbore separation column with fast resistive heating. One of the major problems with the reduction of column dimensions for micro gas chromatography is the availability of a stationary phase that provides good separation performance. In this report, we present the first integration of single-wall carbon nanotubes (SWNTs) as a stationary phase into 100 μm × 100 μm square and 50-cm-long microfabricated channels. The small size of this column with integrated resistive heater and the robustness of the SWNT phase allow for fast temperature programming of up to 60 °C/s. A combination of the fast temperature programming and the narrow peak width of small-volume injections that can be obtained from a high-speed, dual-valve injection system allows for rapid separations of gas mixtures. We demonstrate highly reproducible separations of four-compound test mixtures on these columns in less than ...
136 citations
TL;DR: It is demonstrated that complex interactions of adsorbed species with the device substrate and the surrounding electrolyte can produce significant and sometimes unexpected effects on the device characteristics.
Abstract: Carbon nanotube transistors are a promising platform for the next generation of nonoptical biosensors. However, the exact nature of the biomolecule interactions with nanotubes in these devices remains unknown, creating one of the major obstacles to their practical use. We assembled alternating layers of oppositely charged polyelectrolytes on the carbon nanotube transistors to mimic gating of these devices by charged molecules. The devices showed reproducible oscillations of the transistor threshold voltage depending on the polarity of the outer polymer layer in the multilayer film. This behavior shows excellent agreement with the predictions of a simple electrostatic model. Finally, we demonstrate that complex interactions of adsorbed species with the device substrate and the surrounding electrolyte can produce significant and sometimes unexpected effects on the device characteristics.
105 citations
Journal Article•
36 citations
30 Oct 2006
TL;DR: In this paper, a rigid inorganic shell is applied to suspended carbon nanotubes to resist surface tension forces during transfer into the liquid phase and subsequent removal of the coating in the solution phase restores pristine suspended nano-tubes.
Abstract: Suspended carbon nanotube devices are a promising platform for future bio-electronic applications. Suspended carbon nanotube transistors have been previously fabricated in air; however all previous attempts to bring them into liquid failed. We analyze forces acting on the suspended nanotube devices during immersion into liquids and during device operation and show that surface tension forces acting on the suspended nanotubes during transfer into the liquid phase are responsible for the nanotube damage. We have developed a new strategy that circumvents these limitations by coating suspended nanotubes with a rigid inorganic shell in the gas phase. The coating reinforces the nanotubes and allows them to survive transfer through the interface. Subsequent removal of the coating in the solution phase restores pristine suspended nanotubes. We demonstrate that devices fabricated using this technique preserve their original electrical characteristics.