Showing papers by "Norbahiah Misran published in 2022"
TL;DR: In this paper , a metamaterial absorber (MMA) was proposed for SAR reduction from 5G n78 mobile devices at 3.5 GHz, which is co-polarization insensitive at all possible incident angles to ensure absorption of unnecessary EM energies.
Abstract: Abstract Specific absorption rate (SAR) by next-generation 5G mobile devices has become a burning question among engineers worldwide. 5G communication devices will be famous worldwide due to high-speed data transceiving, IoT-based mass applications, etc. Many antenna systems are being proposed for such mobile devices, but SAR is found at a higher rate that requires reduced for human health. This paper presents a metamaterial absorber (MMA) for SAR reduction from 5G n78 mobile devices at 3.5 GHz. The MMA is co-polarization insensitive at all possible incident angles to ensure absorption of unnecessary EM energies obeying the Poynting theorem for energy conservation and thus ensuring smooth communication by the devices. The unit cell size of the absorber is 0.114 $$\lambda$$ λ making it design efficient for array implementation into mobile devices. This absorber has achieved a minimum of 33% reduction of SAR by applying to the 5G n78 mobile phone model, equivalent to SAR by GSM/LTE/UMTS band mobile phones and making it suitable for SAR reduction from next-generation 5G mobile devices.
9 citations
TL;DR: In this paper , the authors proposed a microwave brain imaging system to detect brain tumors using a metamaterial (MTM) loaded three-dimensional (3D) stacked wideband antenna array.
Abstract: Abstract In this paper, proposes a microwave brain imaging system to detect brain tumors using a metamaterial (MTM) loaded three-dimensional (3D) stacked wideband antenna array. The antenna is comprised of metamaterial-loaded with three substrate layers, including two air gaps. One 1 × 4 MTM array element is used in the top layer and middle layer, and one 3 × 2 MTM array element is used in the bottom layer. The MTM array elements in layers are utilized to enhance the performance concerning antenna’s efficiency, bandwidth, realized gain, radiation directionality in free space and near the head model. The antenna is fabricated on cost-effective Rogers RT5880 and RO4350B substrate, and the optimized dimension of the antenna is 50 × 40 × 8.66 mm 3 . The measured results show that the antenna has a fractional bandwidth of 79.20% (1.37–3.16 GHz), 93% radiation efficiency, 98% high fidelity factor, 6.67 dBi gain, and adequate field penetration in the head tissue with a maximum of 0.0018 W/kg specific absorption rate. In addition, a 3D realistic tissue-mimicking head phantom is fabricated and measured to verify the performance of the antenna. Later, a nine-antenna array-based microwave brain imaging (MBI) system is implemented and investigated by using phantom model. After that, the scattering parameters are collected, analyzed, and then processed by the Iteratively Corrected delay-multiply-and-sum algorithm to detect and reconstruct the brain tumor images. The imaging results demonstrated that the implemented MBI system can successfully detect the target benign and malignant tumors with their locations inside the brain.
3 citations
TL;DR: In this paper , a metamaterial absorber (MMA) is presented aiming absorption of microwave signals from Wi-Fi frequencies of 2.4 GHz and 5 GHz with the flexibility of on-design tuning of maximum absorption frequencies.
Abstract: In this article, a simple metamaterial absorber (MMA) is presented aiming absorption of microwave signals from Wi-Fi frequencies of 2.4 GHz, and 5 GHz. The MMA unit cell constructed on 20 × 20 mm 2 FR4 substrate provides maximum absorption of 99.2% and 99.9% at 2.4 GHz and 5 GHz with the flexibility of on-design tuning of maximum absorption frequencies. The tuning metallic stubs connected with the outer ring provide the provision of frequency adjustment from 2.34 GHz to 2.45 GHz, whereas middle ring stubs along with the innermost ring assists for frequency tuning from 4.68 GHz to 5.1 GHz. Due to symmetrical structure, excellent angular stability up to 60° is achieved with near zero cross-polarization effect for both transverse electric (TE) and transverse magnetic (TM) modes of excitation. The measured result of the proposed MMA is analyzed that shows good similarity with the simulated one. Due to its simplistic design within nominal dimension, high absorption, flexibility to frequency tuning, wide angular stability, and no cross-polarization effect, this MMA can be a good candidate for absorber applications in wireless communication systems, especially for wave shielding from Wi-Fi frequencies.
3 citations
TL;DR: In this paper , a novel metamaterial (MTM) with a mirror symmetric resonator that exhibits multiple resonances of transmission coefficient covering the L, S, C, and X bands is presented.
Abstract: This article presents a novel metamaterial (MTM) with a mirror symmetric resonator that exhibits multiple resonances of transmission coefficient covering the L, S, C, and X bands. The resonating patch is constructed on a low-loss Rogers (RT5880) substrate with a dimension of 20 × 20 × 1.575 mm3. It consists of four equal quartiles with each quartile made with interconnected split-ring resonators; the quartiles are in mirror symmetry with each other. The proposed MTM exhibits resonances at 1.98 GHz, 3.67 GHz, 4.74 GHz, 8.38 GHz, and 10.8 GHz, and electromagnetic characterization is performed through studies of permittivity, permeability, refractive index, and impedances. Power analysis is also performed, and the effect of polarized incident waves is studied. An electromagnetic characterization study reveals that the proposed MTM shows negative permittivity with near-zero permeability and refractive index. It also reveals very little power consumption in the vicinity of the resonances. The dielectric-based frequency tuning is studied by using different dielectric layers over the patch that provides good frequency tuning; this method provides flexibility for adjusting the resonance frequencies in accordance with the application demand. The measured result of the proposed unit cell with the dielectric layer is extracted using a vector network analyzer, and the results exhibit good similarity with the simulated ones. The above-mentioned properties, along with a good effective medium ratio (EMR) of 7.57 indicate that this MTM is suitable for frequency selective applications in microwave devices such as antenna performance improvement and sensing.
2 citations
TL;DR: In this paper , a novel metamaterial (MTM) with a mirror symmetric resonator that exhibits multiple resonances of transmission coefficient covering the L, S, C, and X bands is presented.
Abstract: This article presents a novel metamaterial (MTM) with a mirror symmetric resonator that exhibits multiple resonances of transmission coefficient covering the L, S, C, and X bands. The resonating patch is constructed on a low-loss Rogers (RT5880) substrate with a dimension of 20 × 20 × 1.575 mm3. It consists of four equal quartiles with each quartile made with interconnected split-ring resonators; the quartiles are in mirror symmetry with each other. The proposed MTM exhibits resonances at 1.98 GHz, 3.67 GHz, 4.74 GHz, 8.38 GHz, and 10.8 GHz, and electromagnetic characterization is performed through studies of permittivity, permeability, refractive index, and impedances. Power analysis is also performed, and the effect of polarized incident waves is studied. An electromagnetic characterization study reveals that the proposed MTM shows negative permittivity with near-zero permeability and refractive index. It also reveals very little power consumption in the vicinity of the resonances. The dielectric-based frequency tuning is studied by using different dielectric layers over the patch that provides good frequency tuning; this method provides flexibility for adjusting the resonance frequencies in accordance with the application demand. The measured result of the proposed unit cell with the dielectric layer is extracted using a vector network analyzer, and the results exhibit good similarity with the simulated ones. The above-mentioned properties, along with a good effective medium ratio (EMR) of 7.57 indicate that this MTM is suitable for frequency selective applications in microwave devices such as antenna performance improvement and sensing.
2 citations
TL;DR: Three approaches for automatic segmentation of nonstationary EM emission signals are proposed: short-time energy (STE), long-time zero-crossing rate (STZCR), and short- time kurtosis (STK).
Abstract: Characterizing complex and multi-functional devices is a very challenging task. One problem in statistical near field analysis on complex electronic products is the emergence of nonstationary electromagnetic (EM) signals. Such emergence will lead to an incorrect decision if the signal is used as an input to propagation analysis. The most appropriate approach to this problem seems to be one based on the segmentation of the nonstationary time series obtained from measurements into an ensemble of piecewise stationary signals. In this paper, we propose three approaches for automatic segmentation of nonstationary EM emission signals: short-time energy (STE), short-time zero-crossing rate (STZCR), and short-time kurtosis (STK). Test results show that STE is the best in terms of success in segmenting the nonstationary signals to achieve piecewise stationary time series and being less computationally intensive.
TL;DR: In this article , the analysis techniques for EM emissions including Open Area Test Site (OATS), Anechoic chamber, Transverse Electromagnetics TEM Cell, Compact Antenna Test Range (CATR), and near field scanning are reviewed comprehensively.
Abstract: Nowadays, electronic products are being used extensively in many fields and applications. The dense population of electronic devices in human life has become a challenge for microwave engineers to ensure that their products can meet the Electromagnetic Compatibility (EMC) standards. Complex electronic products with smaller sizes and denser components will be a challenge for compliance with EMC standards. In addition, the occurrence of non-stationary emission at certain operating modes becomes a challenge for analysis. Error in analyzing EM emissions will make the products unable to meet the requirements of EMC standards; hence, they will be prohibited to be marketed. Currently, there are two methods of emission analysis, i.e. by measurement and modeling or computation. There are some problems, however, in the analysis of EM emissions regarding the area of test, complexity, DUT positioning error, installation cost, and time consumption. In this paper, the analysis techniques for EM emissions including Open Area Test Site (OATS), Anechoic chamber, Transverse Electromagnetics TEM Cell, Compact Antenna Test Range (CATR) and near field scanning are reviewed comprehensively. This survey covered EMC standards, principles of EM emission measurement techniques, advantages and disadvantages of EM emission measurement techniques, studies and applications of each technique, recommendations for which technique to be used, and challenges for future research in EM emission measurement. The final section of this paper discusses the challenges for near-field measurements related to the non-stationary emissions phenomenon. This papers also presents the challenges of how to detect and characterize them.