http://www.mate.tue.nl/mate/pdfs/1606.pdf

Survey A review of methods for input/output selection

https://isiarticles.com/bundles/Article/pre/pdf/12025.pdf

Robust control of an electromagnetic active suspension system : simulations and measurements

New technological advances and the requirements to increasingly abide
by new safety laws in engineering design projects highly affects industrial
products in areas such as automotive, aerospace and railway industries.
The necessity arises to design reduced-cost hi-tech products with minimal
complexity, optimal performance, effective parameter robustness properties,
and high reliability with fault tolerance. In this context the control system
design plays an important role and the impact is crucial relative to the level
of cost efficiency of a product.
Measurement of required information for the operation of the design
control system in any product is a vital issue, and in such cases a number of
sensors can be available to select from in order to achieve the desired system
properties. However, for a complex engineering system a manual procedure
to select the best sensor set subject to the desired system properties can
be very complicated, time consuming or even impossible to achieve. This is
more evident in the case of large number of sensors and the requirement to
comply with optimum performance.
The thesis describes a comprehensive study of sensor selection for control
and fault tolerance with the particular application of an ElectroMagnetic
Levitation system (being an unstable, nonlinear, safety-critical system with
non-trivial control performance requirements). The particular aim of the
presented work is to identify effective sensor selection frameworks subject to
given system properties for controlling (with a level of fault tolerance) the
MagLev suspension system. A particular objective of the work is to identify
the minimum possible sensors that can be used to cover multiple sensor faults,
while maintaining optimum performance with the remaining sensors.
The tools employed combine modern control strategies and multiobjective
constraint optimisation (for tuning purposes) methods. An important part
of the work is the design and construction of a 25kg MagLev suspension
to be used for experimental verification of the proposed sensor selection
frameworks.

Optimised configuration of sensing elements for control and fault tolerance applied to an electro-magnetic suspension system

The introduction of permanent magnets has significantly improved the performance and efficiency of advanced actuation systems. The demand for these systems in the industry is increasing and the specifications are becoming more challenging. Accurate and fast modeling of the electromagnetic phenomena is therefore required during the design stage to allow for multi-objective optimization of various topologies. This thesis presents a generalized technique to design and analyze 2D electromagnetic problems based on harmonic modeling. Therefore, the prior art is extended and unified to create a methodology which can be applied to almost any problem in the Cartesian, polar and axisymmetric coordinate system. This generalization allows for the automatic solving of complicated boundary value problems within a very short computation time. This method can be applied to a broad class of classical machines, however, more advanced and complex electromagnetic actuation systems can be designed or analyzed as well. The newly developed framework, based on the generalized harmonic modeling technique, is extensively demonstrated on slotted tubular permanent magnet actuators. As such, numerous tubular topologies, magnetization and winding configurations are analyzed. Additionally, force profiles, emf waveforms and synchronous inductances are accurately predicted. The results are within approximately 5 % of the non-linear finite element analysis including the slotted stator effects. A unique passive damping solution is integrated within the tubular permanent magnet actuator using eddy current damping. This is achieved by inserting conductive rings in the stator slot openings to provide a passive damping force without compromising the tubular actuator’s performance. This novel idea of integrating conductive rings is secured in a patent. A method to calculate the damping ratio due to these conductive rings is presented where the position, velocity and temperature dependencies are shown. The developed framework is applied to the design and optimization of a directdrive electromagnetic active suspension system for passenger cars. This innovative solution is an alternative for currently applied active hydraulic or pneumatic suspension systems for improvement of the comfort and handling of a vehicle. The electromagnetic system provides an improved bandwidth which is typically 20 times higher together with a power consumption which is approximately five times lower. As such, the proposed system eliminates two of the major drawbacks that prevented the widespread commercial breakthrough of active suspension systems. The direct-drive electromagnetic suspension system is composed of a coil spring in parallel with a tubular permanent magnet actuator with integrated eddy current damping. The coil spring supports the sprung mass while the tubular actuator either consumes, by applying direct-drive vertical forces, or regenerates energy. The applied tubular actuator is designed using a non-linear constrained optimization algorithm in combination with the developed analytical framework. This ensured the design with the highest force density together with low power consumption. In case of a power breakdown, the integrated eddy current damping in the slot openings of this tubular actuator, together with the passive coil spring, creates a passive suspension system to guarantee fail-safe operation. To validate the performance of the novel proof-of-concept electromagnetic suspension system, a prototype is constructed and a full-scale quarter car test setup is developed which mimics the vehicle corner of a BMW 530i. Consequently, controllers are designed for the active suspension strut for improvement of either comfort or handling. Finally, the suspension system is installed as a front suspension in a BMW 530i test vehicle. Both the extensive experimental laboratory and on-road tests prove the capability of the novel direct-drive electromagnetic active suspension system. Furthermore, it demonstrates the applicability of the developed modeling technique for design and optimization of electromagnetic actuators and devices.

/pdf/generalized-harmonic-modeling-technique-for-2d-31psvih697.pdf

Generalized harmonic modeling technique for 2D electromagnetic problems : applied to the design of a direct-drive active suspension system

A load-dependent PWA-H∞ controller for semi-active suspensions to exploit the performance of MR dampers

A recently presented method for actuator and sensor selection for linear control systems is applied and evaluated for an active vehicle suspension control problem. The aim is to eliminate the actuator/sensor combinations for which no controller exists that achieves a specified level of robust performance. Complete controller synthesis is avoided by using necessary conditions for robust performance. Due to this, it cannot be guaranteed that a stabilizing and robustly performing controller exists for the combinations satisfying the conditions. This is a major shortcoming of the method. Depending on the application and implementation, the computation time consumed by the selection procedure can be large.

Actuator and sensor selection for an active vehicle suspension aimed at robust performance

This paper presents controller design methods for dynamical systems that are observed by discrete sensors. These sensors induce a partitioning of the state space and only this quantized information is available for the controller. The so-called 'quantized system' is modelled by a discrete-event model that serves as a basis for the controller design methods. However, instead of using solely the classical control methodologies for discrete-event systems as found in the literature, improvements are proposed by including additional information provided by the fact that the underlying plant is continuous by nature, such as continuity of the state trajectories and information on derivatives that holds for parts of the state space. The concept of discretely controlled invariant sets will play a crucial role in the development of control strategies and necessary and sufficient conditions for controlled invariance are presented. Also algorithms are included to compute the smallest and largest discretely controlled...

Pphh Patrick Philips

Papers

Actuator and sensor selection for an active vehicle suspension aimed at robust performance

Control of quantized systems based on discrete event models