第12次 아시아ㆍ太平洋 矯政局長會議 參加記

A new class of martensitic stainless steel, namely 06Cr15Ni4CuMo, with applications in marine engineering, was processed by using selective laser melting (SLM). A body-centered cubic martensitic microstructure was observed, and the microstructure was compared with wrought 410 martensitic stainless steel. The SLM-processed sample showed a hardness of 465 ± 10 HV0.5, which was nearly 115 HV0.5 less than the wrought counterpart. Similarly, the SLM-processed sample showed improved YS and UTS, compared with the wrought sample. However, reduced ductility was observed in the SLM-processed sample due to the presence of high dislocation density in these samples. In addition, 71% volume high-angle grain boundaries were observed, corroborating the high strength of the material. The corrosion behavior was investigated in seawater, and the corrosion resistance was found to be 0.025 mmpy for the SLM-processed 06Cr15Ni4CuMo steel and 0.030 mmpy for wrought 410 alloys, showing better corrosion resistance in the SLM-processed material.

/pdf/microstructure-mechanical-properties-and-corrosion-behavior-21u31w9x.pdf

Microstructure, Mechanical Properties, and Corrosion Behavior of 06Cr15Ni4CuMo Processed by Using Selective Laser Melting

A357 aluminium alloy produced by LPBF: Tribological behaviour in dry sliding conditions

Effect of Ti on the microstructure and wear behavior of a selective laser melted Al-Cu-Mg-Si alloy

Due to the rapidly degradative mechanical performance of selective laser melted (SLM) Al–12Si at elevated temperatures, an Al–12Si–Ti alloy was synthesized by SLM processing with a powder mixture consisting of Al–12Si and 1 wt% of Ti nanoparticles to improve its thermal stability at mid-temperatures (573 K). The results demonstrate that the addition of Ti nanoparticles (i) enlarges the parameter window of SLM processing (power inputs of 200–350 W and scanning speeds of 600–1600 mm/s), (ii) stimulates a columnar to equiaxed transition and refinement of grains (average grain size decreases from 9.0 μm to 1.5 μm), (iii) forms Al 3 Ti phase improving the thermal stability of Al–Si eutectic cell structure, and (iv) partially suppresses the precipitation of Si phase and coarsening of cell structure at elevated temperatures. These features lead to an improved yield strength of SLM Al–12Si–Ti compared with SLM Al–12Si. Specifically, SLM Al–12Si–Ti annealed at 573 K possesses a higher yield strength (297 ± 10 MPa) than SLM Al–12Si (207 ± 9 MPa) annealed at the same conditions. This study will pave the way for the design and synthesis of SLM Al alloys with improved structural and mechanical stability by minor alloying via nanoparticle addition. • Al–12Si–Ti alloy with a broad processing window is designed and fabricated by selective laser melting (SLM). • SLM Al–12Si–Ti alloy has high microstructural stability and mechanical performance under an annealing temperature of 573K. • Addition of Ti can promote the columnar to equiaxed transition and refinement of grains. • Addition of Ti leads to the formation of Al 3 Ti precipitates enhancing the thermal stability of eutectic Al–Si cell. • Addition of Ti can suppress microstructural change, thereby maintaining a higher strength than Al–12Si annealled at 573K. 

Enhancement in strength and thermal stability of selective laser melted Al–12Si by introducing titanium nanoparticles

Al-7Si-0.5 Mg-0.5Cu alloy specimens have been fabricated by selective laser melting (SLM). In this study, the effects of solution treatment, quenching, and artificial aging on the microstructural evolution, as well as mechanical and wear properties, have been investigated. The as-prepared samples show a heterogeneous cellular microstructure with two different cell sizes composed of α-Al and Si phases. After solution-treated and quenched (SQ) heat treatment, the cellular microstructure disappears, and coarse and lumpy Si phase precipitates and a rectangular Cu-rich phase were observed. Subsequent aging after solution-treated and quenched (SQA) heat treatment causes the formation of nanosized Cu-rich precipitates. The as-prepared SLMs sample has good mechanical properties and wear resistance (compressive yield strength: 215 ± 6 MPa and wear rate 2 × 10–13 m3/m). The SQ samples with lumpy Si particles have the lowest strength of 167 ± 13 MPa and the highest wear rate of 6.18 × 10–13 m3/m. The formation of nanosized Cu-rich precipitates in the SQA samples leads to the highest compressive yield strength of 233 ± 6 MPa and a good wear rate of 5.06 × 10–13 m3/m.

Selective Laser Melting of Al-7Si-0.5 Mg-0.5Cu: Effect of Heat Treatment on Microstructure Evolution, Mechanical Properties and Wear Resistance

In this study, the wear behavior of a heat-treatable Al-7Si-0.5Mg-0.5Cu alloy fabricated by selective laser melting was investigated systematically. Compared with the commercial homogenized AA2024 alloy, the fine secondary phase of the SLM Al-Cu-Mg-Si alloy leads to a low specific wear rate (1.8 ± 0.11 × 10−4 mm3(Nm)−1) and a low average coefficient of friction (0.40 ± 0.01). After the T6 heat treatment, the SLM Al-Cu-Mg-Si alloy exhibits a lower specific wear rate (1.48 ± 0.02 × 10−4 mm3(Nm)−1), but a similar average coefficient of friction (0.34 ± 0.01) as the heat-treated AA2024 alloy. Altogether, the SLM Al-3.5Cu-1.5Mg-1Si alloy is suitable for the achievement of not only superior mechanical performance, but also improved tribological properties.

Si-Jie Yu

Papers

Selective Laser Melting of Al-7Si-0.5 Mg-0.5Cu: Effect of Heat Treatment on Microstructure Evolution, Mechanical Properties and Wear Resistance

Wear Behavior of a Heat-Treatable Al-3.5Cu-1.5Mg-1Si Alloy Manufactured by Selective Laser Melting