An overview of the chemical composition of biomass

This paper reviews the crystal chemistry, synthesis, densification, microstructure, mechanical properties, and oxidation behavior of zirconium diboride (ZrB2) and hafnium diboride (HfB2) ceramics. The refractory diborides exhibit partial or complete solid solution with other transition metal diborides, which allows compositional tailoring of properties such as thermal expansion coefficient and hardness. Carbothermal reduction is the typical synthesis route, but reactive processes, solution methods, and pre-ceramic polymers can also be used. Typically, diborides are densified by hot pressing, but recently solid state and liquid phase sintering routes have been developed. Fine-grained ZrB2 and HfB2 have strengths of a few hundred MPa, which can increase to over 1 GPa with the addition of SiC. Pure diborides exhibit parabolic oxidation kinetics at temperatures below 1100°C, but B2O3 volatility leads to rapid, linear oxidation kinetics above that temperature. The addition of silica scale formers such as SiC or MoSi2 improves the oxidation behavior above 1100°C. Based on their unique combination of properties, ZrB2 and HfB2 ceramics are candidates for use in the extreme environments associated with hypersonic flight, atmospheric re-entry, and rocket propulsion.

Refractory Diborides of Zirconium and Hafnium

This article presents an overview of the developments in stainless steels made since the 1990s. Some of the new applications that involve the use of stainless steel are also introduced. A brief introduction to the various classes of stainless steels, their precipitate phases and the status quo of their production around the globe is given first. The advances in a variety of subject areas that have been made recently will then be presented. These recent advances include (1) new findings on the various precipitate phases (the new J phase, new orientation relationships, new phase diagram for the Fe–Cr system, etc.); (2) new suggestions for the prevention/mitigation of the different problems and new methods for their detection/measurement and (3) new techniques for surface/bulk property enhancement (such as laser shot peening, grain boundary engineering and grain refinement). Recent developments in topics like phase prediction, stacking fault energy, superplasticity, metadynamic recrystallisation and the calculation of mechanical properties are introduced, too. In the end of this article, several new applications that involve the use of stainless steels are presented. Some of these are the use of austenitic stainless steels for signature authentication (magnetic recording), the utilisation of the cryogenic magnetic transition of the sigma phase for hot spot detection (the Sigmaplugs), the new Pt-enhanced radiopaque stainless steel (PERSS) coronary stents and stainless steel stents that may be used for magnetic drug targeting. Besides recent developments in conventional stainless steels, those in the high-nitrogen, low-Ni (or Ni-free) varieties are also introduced. These recent developments include new methods for attaining very high nitrogen contents, new guidelines for alloy design, the merits/demerits associated with high nitrogen contents, etc.

Recent developments in stainless steels

A critical review of the literature on the various aspects of natural fibers and biocomposites with a particular reference to chemical modifications is presented in this paper. A notable disadvantage of natural fibers is their polarity which makes it incompatible with hydrophobic matrix. This incompatibility results in poor interfacial bonding between the fibers and the matrix. This in turn leads to impaired mechanical properties of the composites. This defect can be remedied by chemical modification of fibers so as to make it less hydrophilic. This paper reviews the latest trends in chemical modifications and characterizations of natural fibers. The structure and properties of natural fibers have been discussed. Common chemical modifications and their mechanisms have also been elaborated. The importance of chemical modifications and the resultant enhancement in the properties of the composites have also been reviewed. Recent investigations dealing with chemical modifications of natural fiber-reinforced composites have also been cited. POLYM. COMPOS., 29:187‐

Recent Developments in Chemical Modification and Characterization of Natural Fiber-Reinforced Composites

This Minireview systematically examines optical properties of silver nanoparticles as a function of size. Extinction, scattering, and absorption cross-sections and distance dependence of the local electromagnetic field, as well as the quadrupolar coupling of 2D assemblies of such particles are experimentally measured for a wide range of particle sizes. Such measurements were possible because of the development of a novel synthetic method for the size-controlled synthesis of chemically clean, highly crystalline silver nanoparticles of narrow size distribution. The method and its unique advantages are compared to other methods for synthesis of metal nanoparticles. Synthesis and properties of nanocomposite materials using these and other nanoparticles are also described. Important highlights in the history of the field of metal nanoparticles as well as an examination of the basic principles of plasmon resonances are included.

https://nathan.instras.com/ResearchProposalDB/doc-220.pdf

Synthesis and Optical Properties of Silver Nanoparticles and Arrays

Mechanically activated granulated blast furnace slag (GBFS) was used in the range of 50–95% to replace clinker in portland slag cement (PSC). The slag and clinker were activated separately using an attrition mill and mixed to prepare cement formulations. Use of activated slag resulted in a remarkable increase in strength vis-a-vis commercial slag cement. Both 1-day and 28-day strength were found to increase with an increase in slag content up to 70%. The strength of the sample containing 80–85% slag was comparable to the commercial cement used as a reference. It was observed that mechanical activation of slag was more critical from the point of view of strength development. The hydrated cement samples were characterised using powder X-ray diffraction (XRD), scanning electron microscopy with X-ray microanalysis (SEM-EDS) and simultaneous thermogravimetry and differential thermal analysis (TG/DTA). It is established that microstructural changes resulting from enhanced reactivity of slag and densification are related with the improvement in cement strength.

Mechanical activation of granulated blast furnace slag and its effect on the properties and structure of portland slag cement

Bamboo is supposed to be one of the best functionally gradient composite materials available. In a piece of bamboo, not only the number of fibres (‘vascular bundles’) but also the fibre quality varies from outer to inner-most periphery. It has been observed that near the outer periphery, within 1 mm2 area, the number of fibres is approximately 8 whereas the same at the inner-most periphery is approximately 2. Again the cross-sectional shape of fibre at outer periphery is almost circular (diameter 0.14 mm) and compacted but at the inner-most periphery, a fibre (diameter of major axis 0.93 × diameter of minor axis 0.78 mm) has been sprayed, and contain matrix in it. This structural behaviour causes the variation of tensile strength, e.g., the strength of a fibre at the outer periphery is about 160 kg/mm2 and the same at the inner-most periphery is only 45 kg/mm2. It has also been observed that the matrix of bamboo can preferentially be removed from the fibre by alkali treatment. 10% NaOH can remove adhered matrix with little effect on fibres while 20% or stronger alkali reduces the strength of fibre.

/pdf/bamboo-a-functionally-graded-composite-correlation-between-5f2h0u2xnm.pdf

Bamboo—A functionally graded composite-correlation between microstructure and mechanical strength

Microstructural characterization of bamboo

Synthesis of pure and Sr-doped LaGaO3, LaFeO3 and LaCoO3 and Sr,Mg-doped LaGaO3 for ITSOFC application using different wet chemical routes

A detailed study on the sintering behavior of zirconium diboride powder produced by the self-propagating high-temperature synthesis (SHS) process was carried out in the temperature range of 1500–1800 °C. The fine powder prepared by the SHS process exhibited excellent sinterability and could be sintered at 1800 °C for 1 h to approximately 94% of the theoretical density. The apparent activation energy of densification in the range of 1500–1800 °C was estimated to be 248 ± 4 kJ mol−1. A zirconium dioxide layer formed on the surface of the sintered body and was attributed to boron oxide formation during sintering and concurrent surface oxidation by the oxygen generated from the reduction of boron oxide in the carbonaceous atmosphere. Sintering aids like Fe and Cr appeared to help in densification of ZrB2 powder.

Swapan K Das

Papers

Mechanical activation of granulated blast furnace slag and its effect on the properties and structure of portland slag cement

Bamboo—A functionally graded composite-correlation between microstructure and mechanical strength

Microstructural characterization of bamboo

Synthesis of pure and Sr-doped LaGaO3, LaFeO3 and LaCoO3 and Sr,Mg-doped LaGaO3 for ITSOFC application using different wet chemical routes

Sintering studies on ultrafine ZrB2 powder produced by a self-propagating high-temperature synthesis process