There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality.

Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

I and i

Advancing EDM through fundamental insight into the process

The rapid development of the femtosecond laser has revolutionized materials processing due to its unique characteristics of ultrashort pulse width and extremely high peak intensity. The short pulse width suppresses the formation of a heat-affected zone, which is vital for ultrahigh precision fabrication, whereas the high peak intensity allows nonlinear interactions such as multiphoton absorption and tunneling ionization to be induced in transparent materials, which provides versatility in terms of the materials that can be processed. More interestingly, irradiation with tightly focused femtosecond laser pulses inside transparent materials makes three-dimensional (3D) micro- and nanofabrication available due to efficient confinement of the nonlinear interactions within the focal volume. Additive manufacturing (stereolithography) based on multiphoton absorption (two-photon polymerization) enables the fabrication of 3D polymer micro- and nanostructures for photonic devices, micro- and nanomachines, and microfluidic devices, and has applications for biomedical and tissue engineering. Subtractive manufacturing based on internal modification and fabrication can realize the direct fabrication of 3D microfluidics, micromechanics, microelectronics, and photonic microcomponents in glass. These microcomponents can be easily integrated in a single glass microchip by a simple procedure using a femtosecond laser to realize more functional microdevices, such as optofluidics and integrated photonic microdevices. The highly localized multiphoton absorption of a tightly focused femtosecond laser in glass can also induce strong absorption only at the interface of two closely stacked glass substrates. Consequently, glass bonding can be performed based on fusion welding with femtosecond laser irradiation, which provides the potential for applications in electronics, optics, microelectromechanical systems, medical devices, microfluidic devices, and small satellites. This review paper describes the concepts and principles of femtosecond laser 3D micro- and nanofabrication and presents a comprehensive review on the state-of-the-art, applications, and the future prospects of this technology.

Femtosecond laser three-dimensional micro- and nanofabrication

This paper reports on an experimental investigation of small deep hole drilling of Inconel 718 using the EDM process. The parameters such as peak current, pulse on-time, duty factor and electrode speed were chosen to study the machining characteristics. An electrolytic copper tube of 3 mm diameter was selected as a tool electrode. The experiments were planned using central composite design (CCD) procedure. The output responses measured were material removal rate (MRR) and depth averaged surface roughness (DASR). Mathematical models were derived for the above responses using response surface methodology (RSM). The results revealed that MRR is more influenced by peak current, duty factor and electrode rotation, whereas DASR is strongly influenced by peak current and pulse on-time. Finally, the parameters were optimized for maximum MRR with the desired surface roughness value using desirability function approach.

Influence of EDM process parameters in deep hole drilling of Inconel 718

Geopolymer concrete (GPC) has been used as a partial replacement of Portland cement concrete (PCC) in various construction applications. In this paper, two artificial intelligence approaches, namely adaptive neuro fuzzy inference (ANFIS) and artificial neural network (ANN), were used to predict the compressive strength of GPC, where coarse and fine waste steel slag were used as aggregates. The prepared mixtures contained fly ash, sodium hydroxide in solid state, sodium silicate solution, coarse and fine steel slag aggregates as well as water, in which four variables (fly ash, sodium hydroxide, sodium silicate solution, and water) were used as input parameters for modeling. A total number of 210 samples were prepared with target-specified compressive strength at standard age of 28 days of 25, 35, and 45 MPa. Such values were obtained and used as targets for the two AI prediction tools. Evaluation of the model's performance was achieved via criteria such as mean absolute error (MAE), root mean square error (RMSE), and coefficient of determination (R²). The results showed that both ANN and ANFIS models have strong potential for predicting the compressive strength of GPC but ANFIS (MAE = 1.655 MPa, RMSE = 2.265 MPa, and R² = 0.879) is better than ANN (MAE = 1.989 MPa, RMSE = 2.423 MPa, and R² = 0.851). Sensitivity analysis was then carried out, and it was found that reducing one input parameter could only make a small change to the prediction performance.

https://www.mdpi.com/1996-1944/12/6/983/pdf

Artificial Intelligence Approaches for Prediction of Compressive Strength of Geopolymer Concrete.

There is obtained a laser processing method by which an excellent shape of a cut surface can be achieved and an increase in cost can be suppressed. A laser processing method includes the steps of: preparing a material to be processed; and forming a modified area in the material to be processed, by irradiating the material to be processed with laser beam. In the aforementioned step, pulsed laser beam having a continuous spectrum is focused with a lens, thereby forming a focusing line constituted by a plurality of focuses that are obtained by predetermined bands forming the continuous spectrum of the laser beam, and the material to be processed is irradiated with the laser beam such that at least a part of the focusing line is located on a surface of the material to be processed, thereby forming the modified area on an axis of the focusing line.

Laser processing method

Internal modification process of glass by ultrashort laser pulse (USLP) and its applications to microwelding of glass are presented. A simulation model is developed, which can determine intensity distribution of absorbed laser energy, nonlinear absorptivity and temperature distribution at different pulse repetition rates and pulse energies in internal modification of bulk glass with fs- and ps-laser pulses from experimental modified structure. The formation process of the dual-structured internal modification is clarified, which consists of a teardrop-shaped inner structure and an elliptical outer structure, corresponding to the laser-absorbing region and heat-affected molten region, respectively. Nonlinear absorptivity at high pulse repetition rates increases due to the increase in the thermally excited free electron density for avalanche ionization. USLP enables crack-free welding of glass because the shrinkage stress is suppressed by producing embedded molten pool by nonlinear absorption process, in contrast to conventional continuous wave laser welding where cracks cannot be avoided due to shrinkage stress produced in cooling process. Microwelding techniques of glass by USLP have been developed to join glass/glass and Si/glass using optically contacted sample pairs. The strength of the weld joint as high as that of base material is obtained without pre- and post-heating in glass/glass welding. In Si/glass welding, excellent joint performances competitive with anodic bonding in terms of joint strength and process throughput have been attained.

Yasuhiro Okamoto

Papers

Laser processing method

Internal modification of glass by ultrashort laser pulse and its application to microwelding

Improvement in Surface Characteristics by EDM with Chromium Powder Mixed Fluid

High surface quality welding of aluminum using adjustable ring-mode fiber laser

Surface modification of cemented carbide by EB polishing