This paper presents a new way to design a broadband harvester for harvesting high energy over a low-frequency range of 10–15 Hz. The design comprises a cantilever beam with two parallel grooves to form three dissimilar length parallel branches, each with an unequal concentrated tip mass. The piezoelectric material covers the whole length on both sides of the beam to form a bimorph. Appropriate geometry and mass magnitudes are obtained by a parametric study using the Finite Element Method. The design was simulated in COMSOL Multiphysics to study its response. The first three bending modes were utilized in energy harvesting, resulting in three power peaks at their respective fundamental frequencies. The adequate load resistance determined was 5.62 kΩ, at which maximum power can be harvested. The proposed harvester was compared to two other harvesters presented in the literature for validation: First, an optimized conventional harvester while the proposed harvester is operating at adequate load resistance. Second, a multimodal harvester, while the proposed harvester is operating at a 10 kΩ load. The suggested harvester proved to be more efficient by harvesting sufficiently higher broadband energy and is applicable in a wide range of vibration environments because of its adaptability in design.

Split Cantilever Multi-Resonant Piezoelectric Energy Harvester for Low-Frequency Application

Stable output performance generated from a magneto-mechano-electric generator having self-resonance tunability with a movable proof mass

Numerical investigation of the dispersion features of hydrogen gas under various leakage source conditions in a mobile hydrogen refueling station

Study on hydrogen dispersion in confined space with complex air supply and exhaust system

Effect of the position and the area of the vent on the hydrogen dispersion in a naturally ventilated cubiod space with one vent on the side wall

Visualization of hydrogen jet using deformation of the laser beam profile

Measurements of concentration distribution of hydrogen jet using deflection of center of the laser spot

Studies on hydrogen leakage have mainly focused on the influences of location and geometrical configuration on the distribution of the hydrogen in various spaces. The present study developed a simplified model for the leakage diffusion of hydrogen in an enclosed cuboid space with two vents, at the top and at the bottom, respectively. The effect of different leakage positions on the diffusion of the hydrogen was analyzed. The results showed that when hydrogen diffused vertically from the bottom to the top of the space, the farther the leakage position was from the vent on the side wall, the more hydrogen accumulated. When the hydrogen leaked in the vertical direction from the floor, the distance between the leakage position and the bottom vent had little effect on the horizontal diffusion speed of the hydrogen at the top of the space. The diffusion speed for the leakage in the horizontal direction was faster than that in the vertical direction. When the hydrogen leaked in the horizontal direction from the side wall, the height of the leakage had little effect on the horizontal diffusion speed of the hydrogen at the top of the space. Stratification occurred for models set up in the present study whenever the envelope of 1% mole fraction, or 4% mole fraction, of hydrogen extended to the whole ceiling.

Numerical Analysis of the Hydrogen Dispersion Behavior in Different Directions in a Naturally Ventilated Space

Mechanical vibrations have been an important sustainable energy source, and piezoelectric cantilevers operating at the resonant frequency are regarded as one of the effective mechanisms for converting vibration energy to electricity. This paper focuses on model and experimental investigations of multiple attached masses on tuning a piezoelectric cantilever resonant frequency. A discrete model is developed to estimate the resonant frequencies’ change of a cantilever caused by multiple masses’ distribution on it. A mechanism consisted of a piezoelectric cantilever with a 0.3 g and a 0.6 g movable mass along it, respectively, is used to verify the accuracy of the proposed model experimentally. And another mechanism including a piezoelectric cantilever with two 0.3 g attached masses on it is also measured in the designed experiment to verify the discrete model. Meanwhile, the results from the second mechanism were compared with the results from the first one in which the single attached mass is 0.6 g. Two mechanisms have wildly different frequency bandwidths and sensitivities although the total weight of attached masses is the same, 0.6 g. The model and experimental results showed that frequency bandwidth and sensitivity of a piezoelectric cantilever beam can be adjusted effectively by changing the weight, location, and quantity of attached masses.

/pdf/modeling-and-analysis-of-multiple-attached-masses-tuning-a-26s68f5147.pdf

Yuejuan Li

Papers

Effect of the position and the area of the vent on the hydrogen dispersion in a naturally ventilated cubiod space with one vent on the side wall

Visualization of hydrogen jet using deformation of the laser beam profile

Measurements of concentration distribution of hydrogen jet using deflection of center of the laser spot

Numerical Analysis of the Hydrogen Dispersion Behavior in Different Directions in a Naturally Ventilated Space

Modeling and Analysis of Multiple Attached Masses Tuning a Piezoelectric Cantilever Beam Resonant Frequency