Technologies (Basel) 

About: Technologies (Basel) is an academic journal published by Multidisciplinary Digital Publishing Institute. The journal publishes majorly in the area(s): Computer science & Engineering. It has an ISSN identifier of 2227-7080. It is also open access. Over the lifetime, 219 publications have been published receiving 654 citations.

Development of a Large, Low-Cost, Instant 3D Scanner

Abstract: Three-dimensional scanning serves a large variety of uses. It can be utilized to generate objects for, after possible modification, 3D printing. It can facilitate reverse engineering, replication of artifacts to allow interaction without risking cultural heirlooms and the creation of replacement bespoke parts. The technology can also be used to capture imagery for creating holograms, it can support applications requiring human body imaging (e.g., medical, sports performance, garment creation, security) and it can be used to import real-world objects into computer games and other simulations. This paper presents the design of a 3D scanner that was designed and constructed at the University of North Dakota to create 3D models for printing and numerous other uses. It discusses multiple prospective uses for the unit and technology. It also provides an overview of future directions of the project, such as 3D video capture.

Additive Manufacturing: Reproducibility of Metallic Parts

Abstract: The present study deals with the properties of five different metals/alloys (Al-12Si, Cu-10Sn and 316L—face centered cubic structure, CoCrMo and commercially pure Ti (CP-Ti)—hexagonal closed packed structure) fabricated by selective laser melting. The room temperature tensile properties of Al-12Si samples show good consistency in results within the experimental errors. Similar reproducible results were observed for sliding wear and corrosion experiments. The other metal/alloy systems also show repeatable tensile properties, with the tensile curves overlapping until the yield point. The curves may then follow the same path or show a marginal deviation (~10 MPa) until they reach the ultimate tensile strength and a negligible difference in ductility levels (of ~0.3%) is observed between the samples. The results show that selective laser melting is a reliable fabrication method to produce metallic materials with consistent and reproducible properties.

Tensile Properties of Al-12Si Fabricated via Selective Laser Melting (SLM) at Different Temperatures

Abstract: Additive manufacturing processes such as selective laser melting (SLM) are attracting increasing attention and are regarded as the manufacturing technology of the future, because of their ability to produce near net shaped components of theoretically any shape with added functionality. Various properties, including mechanical, tribological, welding, and corrosion properties, of Al-12Si alloys fabricated via SLM have been extensively studied. However, all of these studies were carried out at ambient conditions. Nevertheless, under working conditions, these alloys experience service temperatures ranging between 373 and 473 K. The present study focuses on the evaluation of the mechanical properties of SLM-fabricated Al-12Si alloys in this temperature range. For this, Al-12Si alloy specimens were annealed at 573 K, a temperature well beyond the test temperature in order to provide a stable microstructure during tensile testing. The plasticity of these materials increases along with the size of the dimples on the fracture surface with increasing tensile test temperature. Moreover, the annealed Al-12Si alloy exhibits appreciable tensile properties when tested between 373 K and 473 K. The results suggest that Al-12Si samples fabricated via SLM may be ideal candidates for automotive applications such as pistons and cylinder heads.

Effect of Particle Size on Microstructure and Mechanical Properties of Al-Based Composite Reinforced with 10 Vol.% Mechanically Alloyed Mg-7.4%Al Particles

Abstract: The effect of Mg-7.4%Al reinforcement particle size on the microstructure and mechanical properties in pure Al matrix composites was investigated. The samples were prepared by hot consolidation using 10 vol.% reinforcement in different size ranges, D, 0 < D < 20 µm (0–20 µm), 20 ≤ D < 40 µm (20–40 µm), 40 ≤ D < 80 µm (40–80 µm) and 80 ≤ D < 100 µm (80–100 µm). The result reveals that particle size has a strong influence on the yield strength, ultimate tensile strength and percentage elongation. As the particle size decreases from 80 ≤ D < 100 µm to 0 < D < 20 µm, both tensile strength and ductility increases from 195 MPa to 295 MPa and 3% to 4% respectively, due to the reduced ligament size and particle fracturing. Wear test results also corroborate the size effect, where accelerated wear is observed in the composite samples reinforced with coarse particles.

Visible Light Communications for Internet of Things: Prospects and Approaches, Challenges, Solutions and Future Directions

Abstract: Visible light communications (VLC) is an emerging and promising concept that is capable of solving the major challenges of 5G and Internet of Things (IoT) communication systems. Moreover, due to the usage of light-emitting diodes (LEDs) in almost every aspect of our daily life VLC is providing massive connectivity for various types of massive IoT communications ranging from machine-to-machine, vehicle-to-infrastructure, infrastructure-to-vehicle, chip-to-chip as well as device-to-device. In this paper, we undertake a comprehensive review of the prospects of implementing VLC for IoT. Moreover, we investigate existing and proposed approaches implemented in the application of VLC for IoT. Additionally, we look at the challenges faced in applying VLC for IoT and offer solutions where applicable. Then, we identify future research directions in the implementation of VLC for IoT.