Journal ArticleDOI
A study on the effect of bonding time on the properties of Al7075 to Ti–6Al–4V diffusion bonded joint
TLDR
In this article, the authors used transient liquid phase bonding and 50μm thick Sn-10Zn-3.5Bi film as interlayer to join two dissimilar aerospace alloys Al7075 and Ti-6Al-4V.About:
This article is published in Materials Letters.The article was published on 2012-06-01. It has received 47 citations till now. The article focuses on the topics: Anodic bonding & Eutectic bonding.read more
Citations
More filters
Journal ArticleDOI
Microstructure and mechanical properties of ultrasonic spot welded Al/Ti alloy joints
TL;DR: In this article, the microstructure, hardness, and tensile properties of solid-state ultrasonic spot welded dissimilar joints between Al5754-O and Ti-6Al-4V alloys with or without a pure Al interlayer were studied.
Journal ArticleDOI
Microstructure and mechanical properties of Ti–6Al–4V/Al1060 joints by ultrasonic-assisted brazing in air
TL;DR: In this paper, ultrasonic-assisted brazing of Ti-6Al-4V alloy and Al1060 alloy was carried out in air and by filling with Al-12Si-wt% alloy at 620°C.
Journal ArticleDOI
Ultrasonic-assisted brazing of Al–Ti dissimilar alloy by a filler metal with a large semi-solid temperature range
TL;DR: In this paper, a new filler metal was designed that had a large solidification temperature range between 517.7 and 179.2°C, which reduced the residual thermal stress at the braze interface.
Journal ArticleDOI
TLP bonding of Ti-6Al-4V and Mg-AZ31 alloys using pure Ni electro-deposited coats
TL;DR: In this article, the effect of bonding temperature, time and pressure on microstructural developments and subsequent mechanical properties across joint interface was studied at a temperature range from 500 to 540 Â c, bonding time from 1 to 60 Â min and bonding pressure from 0 to 0.8 MPa.
Journal ArticleDOI
Microstructure and joining mechanism of Ti/Al dissimilar joint by pulsed gas metal arc welding
TL;DR: In this article, the authors investigated the joining mechanism of TiAl3 precipitations in the weld metal owing to metallurgical reactions of Al with dissolved Ti. Formations of precipitation and Ti/Al interface were discussed in detail.
References
More filters
Book
Tracer Diffusion Data for Metals, Alloys, and Simple Oxides
TL;DR: In this article, the authors present empirical and semi-empirical relations between the Self-Diffus ion Activation Energy and various properties of metal oxides, such as heat, compression, and interstitiality.
Journal ArticleDOI
Properties of low melting point Sn–Zn–Bi solders
Jian Zhou,Yangshan Sun,Feng Xue +2 more
TL;DR: In this article, the melting points, wettabilities, mechanical properties and reliabilities of joints with Cu were investigated by changing Bi or Zn concentration, and the results showed that adding Bi could obviously improve wettability of Sn-Zn base alloys with decrease melting point.
Journal ArticleDOI
Microstructure characteristics in the interface zone of Ti/Al diffusion bonding
Ren Jiangwei,Li Yajiang,Feng Tao +2 more
TL;DR: In this paper, the vacuum diffusion bonding was used to join Ti/Al dissimilar metals by means of diffusion bonding after aluminizing on the surface of the Ti sheet, and the results showed that the interface zone included transition zone on the Ti substrate, aluminized coating and transition on the Al substrate.
Journal ArticleDOI
Formation process of the bonding joint in Ti/Al diffusion bonding
TL;DR: In this article, the process of joint formation can be separated into four stages, and the product of the diffusion reaction is only TiAl3 under a particular range of holding time.