Journal ArticleDOI
Experimental studies of the cutting force and surface morphology of explosively clad Ti–steel plates
Reads0
Chats0
TLDR
In this paper, the surface morphology of the drilled holes and contact area was analyzed for two types of indexable insert drills with different configuration of the tool coatings (TiAlN/AlTiN++TiN and TiAl N/TiN) and the same geometry of insert and fixed machining conditions.About:
This article is published in Measurement.The article was published on 2016-01-01. It has received 65 citations till now. The article focuses on the topics: Surface roughness & Contact area.read more
Citations
More filters
Journal ArticleDOI
Parametric and nonparametric description of the surface topography in the dry and MQCL cutting conditions
Grzegorz Królczyk,Radoslaw W. Maruda,Jolanta B. Krolczyk,Piotr Niesłony,Szymon Wojciechowski,Stanisław Legutko +5 more
TL;DR: In this article, a parametric and nonparametric description of surface topography after turning in the dry and MQCL conditions is presented, with the application of the Infinite Focus G4 microscope.
Journal ArticleDOI
Novel uses of alumina/graphene hybrid nanoparticle additives for improved tribological properties of lubricant in turning operation
TL;DR: In this article, the effect of alumina/graphene (GnP) hybrid nanoparticle additives on tribological properties of lubricant as cutting fluid in turning of AISI 304 steel was investigated.
Journal ArticleDOI
Application of signal to noise ratio and grey relational analysis to minimize forces and vibrations during precise ball end milling
TL;DR: In this article, a method for the minimization of cutting forces and vibrations during precise ball end milling of hardened 55NiCrMoV6 steel is developed, which concentrates on the optimal selection of surface inclination angle α and tool's overhang l.
Journal ArticleDOI
Surface morphology analysis of Duplex Stainless Steel (DSS) in Clean Production using the Power Spectral Density
TL;DR: In this article, the influence of clean manufacturing (green manufacturing) methods on the surface morphology of duplex stainless steel was analyzed using Power Spectral Density for dry and MQCL turning process.
Journal ArticleDOI
Optimisation of process parameters for the orbital and conventional drilling of uni-directional carbon fibre-reinforced polymers (UD-CFRP)
Norbert Geier,Tibor Szalay +1 more
TL;DR: In this paper, the machinability of a hand-laminated uni-directional carbon fiber reinforced polymer (CFRP) was investigated in the case of using a special diamond coated twist drill and a solid carbide end mill (helical milling) with a view to analysing and optimising referent machining parameters.
References
More filters
Journal ArticleDOI
Joining of titanium/stainless steel by explosive welding and effect on interface
TL;DR: In this article, stainless steel-titanium plates were joined explosively employing oblique geometry route at different explosive ratios and the bonding was investigated using optical and scanning electron microscopy and tensile-shearing, bending, hardness and corrosion tests were carried out.
Journal ArticleDOI
Microstructure–property relationship in explosively welded duplex stainless steel–steel
TL;DR: In this paper, the relationship between hardness, tensile shear strength and toughness and microstructure of cladded materials were evaluated, and the impact toughness of the cladded material at a given test temperature is found significantly higher than that of the base material alone because of the high impact-toughness of the duplex stainless steel layer.
Book ChapterDOI
The Areal Field Parameters
TL;DR: The vast majority of surface texture parameters are the field parameters as discussed by the authors, which allow the characterisation of surface heights, slopes, complexity, wavelength content, etc., and are defined in the specification standard ISO 25178 part 2.
Journal ArticleDOI
Microstructure and mechanical properties of Ti/Al explosive cladding
TL;DR: In this article, the authors investigated the microstructure and mechanical properties of TA2 and 2A12 bimetals fabricated by explosive welding and found that they have a wavy bonding interface with a short diffusion area which would make contributions to the limitation of the formation of intermetallic compounds.