How to check thermal stability of composites?
Best insight from top research papers
Thermal stability of composites can be checked using various techniques such as thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) . TGA is used to measure the mass loss of the composite material as a function of temperature or time, which helps identify the specific mechanisms of polymer degradation . DSC, on the other hand, measures the heat flow in the material as a function of temperature, providing information about the thermal transitions and stability of the composite . These techniques can be used to evaluate the thermal stability of composites under different heating rates and atmospheric conditions, such as air and pure nitrogen . Additionally, a deconvolution technique based on fitting log-normal distributions to the mass loss data can be used to separate the thermal decomposition reactions and understand their contributions to the overall degradation process .
Answers from top 4 papers
More filters
| Papers (4) | Insight |
|---|---|
| The provided paper does not specifically mention how to check the thermal stability of composites. | |
| The paper proposes an experimental setup for evaluating the thermal stability of composites and protective hardening coatings operating under high-temperature gas flows. | |
| The paper discusses the evaluation of thermal stability of carbon fibre-reinforced polymer (CFRP) composites by studying the mass loss using thermogravimetry technique at different heating rates and atmospheric conditions. | |
| The provided paper does not provide information on how to check the thermal stability of composites. The paper is about the thermal stability of composites and coatings based on MoSi2-B-Al2O3 when heated in air to 1600 °C. |
Related Questions
How does the charcoal binder proportion affect the thermal stability and mechanical properties of carbon composites?5 answersThe proportion of charcoal binder significantly impacts the thermal stability and mechanical properties of carbon composites. A study on carbon/carbon composites found that optimizing the mixing ratio of filler coke and binder is crucial for enhancing mechanical strength. Additionally, oxidative stabilization through an oxidation process at specific temperatures was shown to improve the compressive strength of carbon composites, with a peak at 290°C. Furthermore, the sintering properties and strength of composites were found to increase with a higher coke yield from pitch in the presence of filler. Another study on brick composites revealed that the addition of biochar to laterite composites influenced their mechanical properties, with different proportions affecting sintering temperatures and mechanical strength. Therefore, the charcoal binder proportion plays a vital role in determining the thermal stability and mechanical performance of carbon composites.
Thermal stability of fullerenes nanocomposites?4 answersThermal stability of fullerenes nanocomposites depends on various factors such as heat treatment, temperature, and the type of matrix material. The effect of heat treatment on the structure, phase composition, and mechanical properties of nanostructured aluminum-matrix composite materials modified with C60 fullerenes has been studied. The thermal stability of Ag-C70 nanocomposite thin film has been investigated by annealing at different temperatures, and it has been observed that the properties of the nanocomposite are not significantly affected up to a temperature of 150 °C. Nanocomposite films of polystyrene (PS) and poly(methyl methacrylate) (PMMA) loaded with different variations of fullerenes have shown improved thermal and thermo-oxidative stabilities, with the radical-scavenging ability of the fullerenes playing a key role. The addition of C60 nanoparticles has been found to improve the thermal stability of vegetable insulating oil in transformers, but degassing is required to avoid oxygen adsorption. Carbon nanofillers, including fullerenes, can influence the thermal stability of polymer nanocomposites by improving the dispersion and interaction between the fillers and the polymer matrix.
How good is thermal stability of nanofiltration membrane?4 answersNanofiltration membranes exhibit good thermal stability. The stability of the membranes is crucial for their long-term operation and performance. In one study, graphene oxide (GO) membranes dried at a moderate temperature of 70 °C showed enhanced stability in an aqueous environment, remaining stable for more than 20 days without physical damage. Another study incorporated terephthalic acid (TPA) molecules into the membrane selective layer, resulting in improved acid stability and long-term performance after exposure to acid solutions. A proposed model of graphene-based membranes with an orthogonal-diagonal nanotexture demonstrated stable structures and maintained the layout of nanometer-sized pores. TiO2-ZrO2 nanofiltration membranes also exhibited stability in an aqueous solution at 90 °C, with constant permeation properties over time. Additionally, a thermally stable thin film composite (TFC) nanofiltration membrane showed excellent thermal stability, with increased water flux and stable rejection as the operating temperature increased.
How does temperature affect the stability of graphene?4 answersTemperature has a significant effect on the stability of graphene. At lower temperatures (below 800 °C), the damage to graphene is limited, with mainly on-set defects observed. However, as the temperature increases, the defect density in graphene gradually increases, leading to the formation of boundary defects and isolated graphene islands. On the other hand, the stability of graphene oxide (GO) in water is influenced by temperature as well. GO membranes dried at higher temperatures (70 °C) exhibit greater aqueous solution stability compared to those dried at room temperature, due to a thermally induced balance in electrostatic repulsion. Additionally, the stability of GO in water is affected by the presence of secondary salts, such as carbonate and sulfate, which can promote the formation of agglomerates and limit its use and mobility in water. Overall, temperature plays a crucial role in determining the stability of graphene and GO in different environments.
Why graphite is thermally stable what is the mechanism?4 answersGraphite is thermally stable due to the presence of a critical defect called a screw dislocation that inhibits lateral growth of graphenic crystallites and prevents AB stacking of Bernal graphite. The screw dislocation winds through the layers of graphite like a spiral staircase, hindering the rearrangement of graphenic fragments into ordered crystallites. Molecular dynamics simulations have shown that these screw dislocations spontaneously form during heating and are annihilated at higher annealing temperatures, allowing for crystallite growth. The mechanism for the thermal stability of graphite oxide involves the stepwise removal of water molecules, hydrogen atoms, and hydroxyl groups, resulting in a decrease in interlayer distances. The thermal reduction of graphite oxide involves the homolysis of C-C bonds in the basal plane, followed by isomerization reactions and the cleavage of 1,3-dioxetane to form CO and CO2.
How to conduct composite reliability measurement?5 answersComposite reliability measurement can be conducted using various methods. One approach is to use a latent variable modeling approach, which involves examining measurement and reliability invariance and combining scale reliability coefficients across studies when these invariance conditions hold. Another method is to establish a mathematic model of the power communication fiber network and collect data on effectiveness, fiber attenuation, bandwidth, time delay, packet loss, and cost from operation data of an existing network. This data is used to evaluate the reliability and service transmission performance of the network. Additionally, a methodology called Composite System based Multi-Area Reliability Model can be used to evaluate the reliability of interconnected power systems. This method considers the entire composite system in detail, allowing for a more accurate modeling of the transmission system.