Failure of metals I : brittle and ductile fracture

Austenite to bainite phase transformation in the heat-affected zone of a high strength low alloy steel

Effects of transformation temperature on variant pairing of bainitic ferrite in low carbon steel

The correlation of microstructural characteristics and toughness of the simulated coarse grained heat affected zone (CGHAZ) of low carbon bainitic steel was investigated in this study. The toughness of simulated specimens was examined by using an instrumented Charpy impact tester after the simulation welding test was conducted with different cooling times. Microstructure observation and crystallographic feature analysis were conducted by means of optical microscope and scanning electron microscope equipped with electron back scattered diffraction (EBSD) system, respectively. The main microstructure of simulated specimen changes from lath martensite to coarse bainite with the increase in cooling time. The deterioration of its toughness occurs when the cooling time ranges from 10 to 50 s compared with base metal toughness, and the toughness becomes even worse when the cooling time increases to 90 s or more. The MA (martensite–austenite) constituent is primary responsible for the low toughness of simulated CGHAZ with high values of cooling time because the large MA constituent reduces the crack initiation energy significantly. For crack propagation energy, the small effective grain size of lath martensite plays an important role in improving the crack propagation energy. By contrast, high misorientation packet boundary in coarse bainite seems to have few contributions to the improvement of the toughness because cleavage fracture micromechanism of coarse bainite is mainly controlled by crack initiation.

Microstructural characteristics and toughness of the simulated coarse grained heat affected zone of high strength low carbon bainitic steel

This review paper is devoted to the local approach to fracture (LAF) for the prediction of the fracture toughness of structural steels. The LAF has been considerably developed over the past two decades, not only to provide a better understanding of the fracture behaviour of materials, in particular the failure micromechanisms, but also to deal with loading conditions which cannot easily be handled with the conventional linear elastic fracture mechanics and elastic-plastic fracture mechanics global approaches. The bases of this relatively newly developed methodology are first presented. Both ductile rupture and brittle cleavage fracture micromechanisms are considered. The ductile-to-brittle transition observed in ferritic steels is also briefly reviewed. Two types of LAF methods are presented: (i) those assuming that the material behaviour is not affected by damage (e.g. cleavage fracture), (ii) those using a coupling effect between damage and constitutive equations (e.g. ductile fracture). The micromechanisms of brittle and ductile fracture investigated in elementary volume elements are briefly presented. The emphasis is laid on cleavage fracture in ferritic steels. The role of second phase particles (carbides or inclusions) and grain boundaries is more thoroughly discussed. The distinction between nucleation and growth controlled fracture is made. Recent developments in the theory of cleavage fracture incorporating both the effect of stress state and that of plastic strain are presented. These theoretical results are applied to the crack tip situation to predict the fracture toughness. It is shown that the ductile-to-brittle transition curve can reasonably be well predicted using the LAF approach. Additional applications of the LAF approach methods are also shown, including: (i) the effect of loading rate and prestressing; (ii) the influence of residual stresses in welds; (iii) the mismatch effects in welds; (iv) the warm-prestressing effect. An attempt is also made to delineate research areas where large improvements should be made for a better understanding of the failure behaviour of structural materials.

Development of the local approach to fracture over the past 25 years: Theory and applications

The effect of the welding cycle on the fracture toughness properties of high-strength low alloy (HSLA) steels is examined by means of thermal simulation of heat-affected zone (HAZ) microstructures. Tensile tests on notched bars and fracture toughness tests at various temperatures are performed together with fracture surface observations and cross-sectional analyses. The influence of martensite-austenite (M-A) constituents and of “crystallographic” bainite packets on cleavage fracture micromechanisms is, thus, evidenced as a function of temperature. Three weakest-link probabilistic models (the “Master-curve” (MC) approach, the Beremin model, and a “double-barrier” (DB) model) are applied to account for the ductile-to-brittle transition (DBT) fracture toughness curve. Some analogy, but also differences, are found between the MC approach and the Beremin model. The DB model, having nonfitted, physically based scatter parameters, is applied to the martensite-containing HAZ microstructures and gives promising results.

Astrid Lambert-Perlade

Papers

Austenite to bainite phase transformation in the heat-affected zone of a high strength low alloy steel

Mechanisms and modeling of cleavage fracture in simulated heat-affected zone microstructures of a high-strength low alloy steel