This paper presents an assessment of the performance of an embedded propulsion system in the presence of distortion associated with boundary layer ingestion. For fan pressure ratios of interest for civil transports, the benefits of boundary layer ingestion are shown to be very sensitive to the magnitude of fan and duct losses. The distortion transfer across the fan, basically the comparison of the stagnation pressure non-uniformity downstream of the fan to that upstream of the fan, has a major role in determining the impact of boundary layer ingestion on overall fuel burn. This, in turn, puts requirements on the fidelity with which one needs to assess the distortion transfer, and thus the type of models that need to be used in such assessment. For the three-dimensional distortions associated with fuselage boundary layers ingested into a subsonic diffusing inlet, it is found that boundary layer ingestion can provide decreases in fuel burn of several per cent. It is also shown that a promising avenue for mitigating the risks (aerodynamic as well as aeromechanical) in boundary layer ingestion is to mix out the flow before it reaches the engine face.

/pdf/performance-of-a-boundary-layer-ingesting-bli-propulsion-3390bkcayq.pdf

Performance of a Boundary Layer Ingesting (BLI) propulsion system

Meeting NASA's N+3 goals requires a fundamental shift in approach to aircraft and engine design. Material and design improvements allow higher pressure and higher temperature core engines which improve the thermal efficiency. Propulsive efficiency, the other half of the overall efficiency equation, however, is largely determined by the fan pressure ratio (FPR). Lower FPR increases propulsive efficiency, but also dramatically reduces fan shaft speed through the combination of larger diameter fans and reduced fan tip speed limits. The result is that below an FPR of 1.5 the maximum fan shaft speed makes direct drive turbines problematic. However, it is the low pressure ratio fans that allow the improvement in propulsive efficiency which, along with improvements in thermal efficiency in the core, contributes strongly to meeting the N+3 goals for fuel burn reduction. The lower fan exhaust velocities resulting from lower FPRs are also key to meeting the aircraft noise goals. Adding a gear box to the standard turbofan engine allows acceptable turbine speeds to be maintained. However, development of a 50,000+ hp gearbox required by fans in a large twin engine transport aircraft presents an extreme technical challenge, therefore another approach is needed. This paper presents a propulsion system which transmits power from the turbine to the fan electrically rather than mechanically. Recent and anticipated advances in high temperature superconducting generators, motors, and power lines offer the possibility that such devices can be used to transmit turbine power in aircraft without an excessive weight penalty. Moving to such a power transmission system does more than provide better matching between fan and turbine shaft speeds. The relative ease with which electrical power can be distributed throughout the aircraft opens up numerous other possibilities for new aircraft and propulsion configurations and modes of operation. This paper discusses a number of these new possibilities. The Boeing N2 hybrid-wing-body (HWB) is used as a baseline aircraft for this study. The two pylon mounted conventional turbofans are replaced by two wing-tip mounted turboshaft engines, each driving a superconducting generator. Both generators feed a common electrical bus which distributes power to an array of superconducting motor-driven fans in a continuous nacelle centered along the trailing edge of the upper surface of the wing-body. A key finding was that traditional inlet performance methodology has to be modified when most of the air entering the inlet is boundary layer air. A very thorough and detailed propulsion/airframe integration (PAI) analysis is required at the very beginning of the design process since embedded engine inlet performance must be based on conditions at the inlet lip rather than freestream conditions. Examination of a range of fan pressure ratios yielded a minimum Thrust-specific-fuel-consumption (TSFC) at the aerodynamic design point of the vehicle (31,000 ft /Mach 0.8) between 1.3 and 1.35 FPR. We deduced that this was due to the higher pressure losses prior to the fan inlet as well as higher losses in the 2-D inlets and nozzles. This FPR is likely to be higher than the FPR that yields a minimum TSFC in a pylon mounted engine. 1

/pdf/turboelectric-distributed-propulsion-engine-cycle-analysis-7up1rf7ovc.pdf

Turboelectric Distributed Propulsion Engine Cycle Analysis for Hybrid-Wing-Body Aircraft

The emergence of distributed electric propulsion (DEP) concepts for aircraft systems has enabled new capabilities in the overall efficiency, capabilities, and robustness of future air vehicles Distributed electric propulsion systems feature the novel approach of utilizing electrically-driven propulsors which are only connected electrically to energy sources or power-generating devices As a result, propulsors can be placed, sized, and operated with greater flexibility to leverage the synergistic benefits of aero-propulsive coupling and provide improved performance over more traditional designs A number of conventional aircraft concepts that utilize distributed electric propulsion have been developed, along with various short and vertical takeoff and landing platforms Careful integration of electrically-driven propulsors for boundary-layer ingestion can allow for improved propulsive efficiency and wake-filling benefits The placement and configuration of propulsors can also be used to mitigate the trailing vortex system of a lifting surface or leverage increases in dynamic pressure across blown surfaces for increased lift performance Additionally, the thrust stream of distributed electric propulsors can be utilized to enable new capabilities in vehicle control, including reducing requirements for traditional control surfaces and increasing tolerance of the vehicle control system to engine-out or propulsor-out scenarios If one or more turboelectric generators and multiple electric fans are used, the increased effective bypass ratio of the whole propulsion system can also enable lower community noise during takeoff and landing segments of flight and higher propulsive efficiency at all conditions Furthermore, the small propulsors of a DEP system can be installed to leverage an acoustic shielding effect by the airframe, which can further reduce noise signatures The rapid growth in flight-weight electrical systems and power architectures has provided new enabling technologies for future DEP concepts, which provide flexible operational capabilities far beyond those of current systems While a number of integration challenges exist, DEP is a disruptive concept that can lead to unprecedented improvements in future aircraft designs

/pdf/a-review-of-distributed-electric-propulsion-concepts-for-air-52jxv86ln9.pdf

A Review of Distributed Electric Propulsion Concepts for Air Vehicle Technology

/pdf/turboelectric-distributed-propulsion-engine-cycle-analysis-1o512c5sut.pdf

The noise goal of the Silent Aircraft Initiative, a collaborative effort between industry, academia and government agencies led by Cambridge University and MIT, demands an airframe design with noise as a prime design variable. This poses a number of design challenges and the necessary design philosophy inherently cuts across multiple disciplines involving aerodynamics, structures, acoustics, mission analysis and operations, and dynamics and control. This paper discusses a novel design methodology synthesizing first principles analysis and high-fidelity simulations, and presents the conceptual design of an aircraft with a calculated noise level of 62 dBA at the airport perimeter. This is near the background noise in a well populated area, making the aircraft imperceptible to the human ear on takeoff and landing. The all-lifting airframe of the conceptual aircraft design also has the potential for a reduced fuel burn of 124 passenger-miles per gallon, a 25% improvement compared to existing commercial aircraft. A key enabling technology in this conceptual design is the aerodynamic shaping of the airframe centerbody which is the main focus of this paper. Design requirements and challenges are identified and the resulting aerodynamic design is discussed in depth. The paper concludes with suggestions for continued research on enabling technologies for quiet commercial aircraft.

/pdf/airframe-design-for-silent-aircraft-2rnk944b2k.pdf

Airframe Design for "Silent Aircraft"

The Silent Aircraft Initiative goal is to design an aircraft that is imperceptible above background noise outside the airport boundary. The aircraft that fulfils this objective must also be economically competitive with conventional aircraft of the future and therefore fuel consumption and mechanical reliability are key considerations for the design. To meet these ambitious targets, a multi-fan embedded turbofan engine with boundary layer ingestion has been proposed. This configuration includes several new technologies including a variable area nozzle, a complex high-power transmission system, a Low Pressure turbine designed for low-noise, an axial-radial HP compressor, advanced acoustic liners and a low-speed fan optimized for both cruise and off-design operation. These technologies, in combination, enable a low-noise and fuel efficient propulsion system but they also introduce significant challenges into the design. These challenges include difficulties in predicting the noise and performance of the new components but there are also challenges in reducing the design risks and proving that the new concepts are realizable. This paper presents the details of the engine configuration that has been developed for the Silent Aircraft application. It describes the design approach used for the critical components and discusses the benefits of the new technologies. The new technologies are expected to offer significant benefits in noise reduction without compromising fuel burn. However, more detailed design and further research are required to fully control the additional risks generated by the system complexity.

Challenges in the silent aircraft engine design

This work describes the effect that the injection of leakage flow from a cavity into the mainstream has on the endwall flows and their interaction with a large pressure surface separation bubble in a low-pressure turbine. The effect of a step in hub diameter ahead of the blade row is also simulated. The blade profile under consideration is a typical design of modern low-pressure turbines. The tests are conducted in a low speed linear cascade. These are complemented by numerical simulations. Two different step geometries are investigated, i.e., a backward-facing step and a forward-facing step. The leakage tangential velocity and the leakage mass flow rate are also modified. It was found that the injection of leakage mass flow gives rise to a strengthening of the endwall flows independently of the leakage mass flow rate and the leakage tangential velocity. The experimental results have shown that below a critical value of the leakage tangential velocity, the net mixed-out endwall losses are not significantly altered by a change in the leakage tangential velocity. For these cases, the effect of the leakage mass flow is confined to the wall, as the inlet endwall boundary layer is pushed further away from the wall by the leakage flow. However, for values of the leakage tangential velocity around 100% of the wheelspeed, there is a large increase in losses due to a stronger interaction between the endwall flows and the leakage mass flow. This gives rise to a change in the endwall flows structure. In all cases, the presence of a forward-facing step produces a strengthening of the endwall flows and an increase of the net mixed-out endwall losses when compared with a backward-facing step. This is because of a strong interaction with the pressure surface separation bubble.© 2006 ASME

E. de la Rosa Blanco

Papers

Challenges in the silent aircraft engine design

Effect of the Leakage Flows and the Upstream Platform Geometry on the Endwall Flows of a Turbine Cascade

Influence of the state of the inlet endwall boundary layer on pressure surface separations on low pressure turbines