The field of power harvesting has experienced significant growth over the past few years due to the ever-increasing desire to produce portable and wireless electronics with extended lifespans. Current portable and wireless devices must be designed to include electrochemical batteries as the power source. The use of batteries can be troublesome due to their limited lifespan, thus necessitating their periodic replacement. In the case of wireless sensors that are to be placed in remote locations, the sensor must be easily accessible or of a disposable nature to allow the device to function over extended periods of time. Energy scavenging devices are designed to capture the ambient energy surrounding the electronics and convert it into usable electrical energy. The concept of power harvesting works towards developing self-powered devices that do not require replaceable power supplies. A number of sources of harvestable ambient energy exist, including waste heat, vibration, electromagnetic waves, wind, flowing water, and solar energy. While each of these sources of energy can be effectively used to power remote sensors, the structural and biological communities have placed an emphasis on scavenging vibrational energy with piezoelectric materials. This article will review recent literature in the field of power harvesting and present the current state of power harvesting in its drive to create completely self-powered devices.

/pdf/a-review-of-power-harvesting-using-piezoelectric-materials-k69swwfj1u.pdf

A review of power harvesting using piezoelectric materials (2003–2006)

Energy harvesting generators are attractive as inexhaustible replacements for batteries in low-power wireless electronic devices and have received increasing research interest in recent years. Ambient motion is one of the main sources of energy for harvesting, and a wide range of motion-powered energy harvesters have been proposed or demonstrated, particularly at the microscale. This paper reviews the principles and state-of-art in motion-driven miniature energy harvesters and discusses trends, suitable applications, and possible future developments.

/pdf/energy-harvesting-from-human-and-machine-motion-for-wireless-3lsf4oudvo.pdf

Energy Harvesting From Human and Machine Motion for Wireless Electronic Devices

DC–DC converters with voltage boost capability are widely used in a large number of power conversion applications, from fraction-of-volt to tens of thousands of volts at power levels from milliwatts to megawatts. The literature has reported on various voltage-boosting techniques, in which fundamental energy storing elements (inductors and capacitors) and/or transformers in conjunction with switch(es) and diode(s) are utilized in the circuit. These techniques include switched capacitor (charge pump), voltage multiplier, switched inductor/voltage lift, magnetic coupling, and multistage/-level, and each has its own merits and demerits depending on application, in terms of cost, complexity, power density, reliability, and efficiency. To meet the growing demand for such applications, new power converter topologies that use the above voltage-boosting techniques, as well as some active and passive components, are continuously being proposed. The permutations and combinations of the various voltage-boosting techniques with additional components in a circuit allow for numerous new topologies and configurations, which are often confusing and difficult to follow. Therefore, to present a clear picture on the general law and framework of the development of next-generation step-up dc–dc converters, this paper aims to comprehensively review and classify various step-up dc–dc converters based on their characteristics and voltage-boosting techniques. In addition, the advantages and disadvantages of these voltage-boosting techniques and associated converters are discussed in detail. Finally, broad applications of dc–dc converters are presented and summarized with comparative study of different voltage-boosting techniques.

/pdf/step-up-dc-dc-converters-a-comprehensive-review-of-voltage-6dlytctzg2.pdf

Step-Up DC–DC Converters: A Comprehensive Review of Voltage-Boosting Techniques, Topologies, and Applications

Piezoelectric transduction has received great attention for vibration-to-electric energy conversion over the last five years. A typical piezoelectric energy harvester is a unimorph or a bimorph cantilever located on a vibrating host structure, to generate electrical energy from base excitations. Several authors have investigated modeling of cantilevered piezoelectric energy harvesters under base excitation. The existing mathematical modeling approaches range from elementary single-degree-of-freedom models to approximate distributed parameter solutions in the sense of Rayleigh–Ritz discretization as well as analytical solution attempts with certain simplifications. Recently, the authors have presented the closed-form analytical solution for a unimorph cantilever under base excitation based on the Euler–Bernoulli beam assumptions. In this paper, the analytical solution is applied to bimorph cantilever configurations with series and parallel connections of piezoceramic layers. The base excitation is assumed to be translation in the transverse direction with a superimposed small rotation. The closed-form steady state response expressions are obtained for harmonic excitations at arbitrary frequencies, which are then reduced to simple but accurate single-mode expressions for modal excitations. The electromechanical frequency response functions (FRFs) that relate the voltage output and vibration response to translational and rotational base accelerations are identified from the multi-mode and single-mode solutions. Experimental validation of the single-mode coupled voltage output and vibration response expressions is presented for a bimorph cantilever with a tip mass. It is observed that the closed-form single-mode FRFs obtained from the analytical solution can successfully predict the coupled system dynamics for a wide range of electrical load resistance. The performance of the bimorph device is analyzed extensively for the short circuit and open circuit resonance frequency excitations and the accuracy of the model is shown in all cases.

/pdf/an-experimentally-validated-bimorph-cantilever-model-for-qzwpq105mk.pdf

An experimentally validated bimorph cantilever model for piezoelectric energy harvesting from base excitations

Power consumption is forecast by the International Technology Roadmap of Semiconductors (ITRS) to pose long-term technical challenges for the semiconductor industry. The purpose of this paper is threefold: (1) to provide an overview of strategies for powering MEMS via non-regenerative and regenerative power supplies; (2) to review the fundamentals of piezoelectric energy harvesting, along with recent advancements, and (3) to discuss future trends and applications for piezoelectric energy harvesting technology. The paper concludes with a discussion of research needs that are critical for the enhancement of piezoelectric energy harvesting devices.

/pdf/powering-mems-portable-devices-a-review-of-non-regenerative-30r5zxggdp.pdf

Powering MEMS portable devices—a review of non-regenerative and regenerative power supply systems with special emphasis on piezoelectric energy harvesting systems

This paper presents devices for harvesting energy from regular blood pressure variation in heart cavities Specific challenges of this concept are analyzed First, a very flexible and hermetic packaging solution is proposed Then, piezoelectric and electrostatic transducers are conceived and optimized for the pacemaker application According to our simulations and experiments, the proposed devices should provide the targeted electrical energy of 10 μJ per heartbeat in real environment

Energy harvesting devices as long lasting power sources for the next generation pacemakers

A low cost and low temperature microelectromechanical systems (MEMS) transfer process is presented. The process is based on adhesion control of molded electroplated Ni microstructures on the donor wafer by using a plasma deposited fluorocarbon film. Adhesive bonding of the microstructures on the target wafer using BCB sealing enables mechanical tearing off from the donor wafer. This proposed process has allowed us to realize from 7 μm down to 700 nm thick Ni patterns on Si, Pyrex glass wafers and Kapton foils. Multiple transfers lead to Ni stacked microstructures. We demonstrated the interest of a simple film transfer process for the elaboration of 3D microstructures.

http://jes.ecsdl.org/content/158/5/H545.full.pdf

MEMS Process by Film Transfer Using a Fluorocarbon Anti-Adhesive Layer

This paper highlights the interest of shunt-diode rectifiers to optimize the performances of piezoelectric vibration energy harvesters based on linear load adaptation. It provides, for the first time, a full analytical study of the input power and frequency bandwidth of such a system. We show that this architecture is well-suited for piezoelectric energy harvesting. In the presented approach, a so-called shunt diode is connected across the electrodes of the piezoelectric transducer, which makes the piezoelectric voltage unidirectional instead of alternating. Thus, DC–DC converters usually used for power optimization can be directly connected to the transducer. We show that weakly-coupled linear inertial piezoelectric energy harvesters generate higher power when connected to a shunt-diode rectifier than to a bridge rectifier. Moreover, the frequency bandwidth is enlarged by the use of the single-diode shunt rectifier, especially for strongly-coupled piezoelectric generators. The proposed architecture is also interesting for low piezoelectric voltages, at which voltage drops across the diodes used for AC–DC conversion critically degrade the power efficiency. Experimental results validate the presented analytical study and highlight the higher efficiency of the shunt-diode rectifier circuit. Compared to a standard bridge rectifier architecture, we demonstrate an increase of +43% output power on a weakly-coupled generator and an increase of +5% bandwidth on a strongly-coupled generator.

/pdf/shunt-diode-rectifier-a-new-scheme-for-efficient-4s1xjt37hj.pdf

Shunt-diode rectifier: a new scheme for efficient piezoelectric energy harvesting

The capsule has an energy recovery transducer comprising a capacitor electrode in form of comb coupled to a movable actuation member that has a deformable element (42) deformed in response to effect of pressure variations in a medium. The electrode and another capacitor electrode have surfaces separated by dielectric gap to define a capacitor. An energy storage and management module is powered by the transducer based on a reduction in the surfaces and/or an increase of the gap. The element is coupled to the comb by a mechanical high-pass filter (68) for pressure variations in the medium.

Energy recovery device for autonomous intracorporeal capsule

The intra-corporeal autonomous capsule has a transducer that is configured to convert an external force applied to the capsule into electric potential. The transducer with piezoelectric strip is coupled to a movable actuating portion having a rigid surface to directly receive external force. The piezoelectric strip is fixed to a portion of the capsule. An energy storage and management module is powered by a energy harvesting transducer under the effect of deformation of the piezoelectric component due to the external force.

Elie Lefeuvre

Papers

Energy harvesting devices as long lasting power sources for the next generation pacemakers

MEMS Process by Film Transfer Using a Fluorocarbon Anti-Adhesive Layer

Shunt-diode rectifier: a new scheme for efficient piezoelectric energy harvesting

Energy recovery device for autonomous intracorporeal capsule

Autonomous intracorporeal capsule with piezoelectric energy recovery