I
I. N. Belokonova
Researcher at Siberian Federal University
Publications - 9
Citations - 62
I. N. Belokonova is an academic researcher from Siberian Federal University. The author has contributed to research in topics: Scandium & Alloy. The author has an hindex of 3, co-authored 7 publications receiving 24 citations.
Papers
More filters
Journal ArticleDOI
Investigation of the structure and properties of cold-rolled strips from experimental alloy 1580 with a reduced scandium content
I. L. Konstantinov,V. N. Baranov,Sergey B. Sidelnikov,B. P. Kulikov,Aleksandr Innokentyevich Bezrukikh,V. F. Frolov,Tamara A. Orelkina,Denis Sergeevich Voroshilov,Pavel Olegovich Yuryev,I. N. Belokonova +9 more
TL;DR: In this article, the structure and properties of cold-rolled strips with a thickness of 3mm from an experimental aluminum alloy 1580 with a lower scandium content of 0.03% (wt) relative to the grade of the aluminum alloy and a 5083 similar alloy, were studied in the laboratory installation of semicontinuous casting of the foundry department of the Siberian Federal University (Siberian Federal University, Russia, Krasnoyarsk) were used.
Journal ArticleDOI
Study of strength properties of semi-finished products from economically alloyed high-strength aluminium-scandium alloys for application in automobile transport and shipbuilding
V. N. Baranov,Sergey B. Sidelnikov,Evgeny Zenkin,V. F. Frolov,Denis Sergeevich Voroshilov,Olga Yakivyuk,I. L. Konstantinov,Ruslan E. Sokolov,I. N. Belokonova +8 more
TL;DR: In this article, the results of a study on the strength of rolled products from aluminium alloys doped with scandium under various processing conditions of hot and cold rolling are presented.
Journal ArticleDOI
Modeling and Investigation of the Process of Hot Rolling of Large-Sized Ingots from Aluminum Alloy of the Al-Mg System, Economically Alloyed by Scandium
Viktor Mann,Sergey B. Sidelnikov,I. L. Konstantinov,V. N. Baranov,I. N. Dovzhenko,Denis Sergeevich Voroshilov,Ekaterina S. Lopatina,Olga Yakivyuk,I. N. Belokonova +8 more
TL;DR: In this paper, a computer model of the process of hot rolling of ingots from the experimental aluminum alloy which is economically alloyed by scandium is given, with the use of which the straining, temperature and speed processing modes conditions are calculated and also power parameters of processing is calculated in applied to industrial conditions.
Journal ArticleDOI
Influence of Rolling and Annealing Modes on Properties of Sheet Semifinished Products Made of Wrought Aluminum Alloy 1580
I. L. Konstantinov,V. N. Baranov,Sergey B. Sidelnikov,E. Yu. Zenkin,Pavel Olegovich Yuryev,I. N. Belokonova +5 more
TL;DR: In this article, the processability and properties of sheet products made of a large grade 1580-alloy ingot with a lower scandium content in the range of its specifications are analyzed.
Journal ArticleDOI
Study on the influence of heat treatment modes on mechanical and corrosion properties of rolled sheet products from a new aluminum alloy, economically alloyed with scandium
Evgeniy Yu. Zenkin,V. N. Baranov,Sergey B. Sidelnikov,I. L. Konstantinov,Ekaterina S. Lopatina,Olga Yakivyuk,Denis Sergeevich Voroshilov,I. N. Belokonova,Vladimir A. Frolov +8 more
TL;DR: In this article, a study on mechanical and corrosion properties of rolled sheet products from a new alloy of the Al-Mg-Sc system in a deformed and heat treated state is presented.