Multilevel inverter technology has emerged recently as a very important alternative in the area of high-power medium-voltage energy control. This paper presents the most important topologies like diode-clamped inverter (neutral-point clamped), capacitor-clamped (flying capacitor), and cascaded multicell with separate DC sources. Emerging topologies like asymmetric hybrid cells and soft-switched multilevel inverters are also discussed. This paper also presents the most relevant control and modulation methods developed for this family of converters: multilevel sinusoidal pulsewidth modulation, multilevel selective harmonic elimination, and space-vector modulation. Special attention is dedicated to the latest and more relevant applications of these converters such as laminators, conveyor belts, and unified power-flow controllers. The need of an active front end at the input side for those inverters supplying regenerative loads is also discussed, and the circuit topology options are also presented. Finally, the peripherally developing areas such as high-voltage high-power devices and optical sensors and other opportunities for future development are addressed.

Multilevel inverters: a survey of topologies, controls, and applications

The use of distributed energy resources is increasingly being pursued as a supplement and an alternative to large conventional central power stations. The specification of a power-electronic interface is subject to requirements related not only to the renewable energy source itself but also to its effects on the power-system operation, especially where the intermittent energy source constitutes a significant part of the total system capacity. In this paper, new trends in power electronics for the integration of wind and photovoltaic (PV) power generators are presented. A review of the appropriate storage-system technology used for the integration of intermittent renewable energy sources is also introduced. Discussions about common and future trends in renewable energy systems based on reliability and maturity of each technology are presented

/pdf/power-electronic-systems-for-the-grid-integration-of-4s5cxjhatl.pdf

Power-Electronic Systems for the Grid Integration of Renewable Energy Sources: A Survey

Multilevel converters have been under research and development for more than three decades and have found successful industrial application. However, this is still a technology under development, and many new contributions and new commercial topologies have been reported in the last few years. The aim of this paper is to group and review these recent contributions, in order to establish the current state of the art and trends of the technology, to provide readers with a comprehensive and insightful review of where multilevel converter technology stands and is heading. This paper first presents a brief overview of well-established multilevel converters strongly oriented to their current state in industrial applications to then center the discussion on the new converters that have made their way into the industry. In addition, new promising topologies are discussed. Recent advances made in modulation and control of multilevel converters are also addressed. A great part of this paper is devoted to show nontraditional applications powered by multilevel converters and how multilevel converters are becoming an enabling technology in many industrial sectors. Finally, some future trends and challenges in the further development of this technology are discussed to motivate future contributions that address open problems and explore new possibilities.

/pdf/recent-advances-and-industrial-applications-of-multilevel-26fluutoc9.pdf

Recent Advances and Industrial Applications of Multilevel Converters

Multilevel voltage source converters are emerging as a new breed of power converter options for high-power applications. The multilevel voltage source converters typically synthesize the staircase voltage wave from several levels of DC capacitor voltages. One of the major limitations of the multilevel converters is the voltage unbalance between different levels. The techniques to balance the voltage between different levels normally involve voltage clamping or capacitor charge control. There are several ways of implementing voltage balance in multilevel converters. Without considering the traditional magnetic coupled converters, this paper presents three recently developed multilevel voltage source converters: (1) diode-clamp, (2) flying-capacitors, and (3) cascaded-inverters with separate DC sources. The operating principle, features, constraints, and potential applications of these converters are discussed.

/pdf/multilevel-converters-a-new-breed-of-power-converters-wavnnh62ti.pdf

Multilevel converters-a new breed of power converters

This paper presents a technology review of voltage-source-converter topologies for industrial medium-voltage drives. In this highly active area, different converter topologies and circuits have found their application in the market. This paper covers the high-power voltage-source inverter and the most used multilevel-inverter topologies, including the neutral-point-clamped, cascaded H-bridge, and flying-capacitor converters. This paper presents the operating principle of each topology and a review of the most relevant modulation methods, focused mainly on those used by industry. In addition, the latest advances and future trends of the technology are discussed. It is concluded that the topology and modulation-method selection are closely related to each particular application, leaving a space on the market for all the different solutions, depending on their unique features and limitations like power or voltage level, dynamic performance, reliability, costs, and other technical specifications.

Multilevel Voltage-Source-Converter Topologies for Industrial Medium-Voltage Drives

A new neutral-point-clamped pulsewidth modulation (PWM) inverter composed of main switching devices which operate as switches for PWM and auxiliary switching devices to clamp the output terminal potential to the neutral point potential has been developed. This inverter output contains less harmonic content as compared with that of a conventional type. Two inverters are compared analytically and experimentally. In addition, a new PWM technique suitable for an ac drive system is applied to this inverter. The neutral-point-clamped PWM inverter adopting the new PWM technique shows an excellent drive system efficiency, including motor efficiency, and is appropriate for a wide-range variable-speed drive system.

A New Neutral-Point-Clamped PWM Inverter

A new equivalent circuit of induction motor based on the total linkage flux of the secondary windings

/pdf/control-of-pwm-inverter-output-wave-with-reduced-low-order-51b29fup77.pdf

Isao Takahashi

Papers

A New Neutral-Point-Clamped PWM Inverter

A new equivalent circuit of induction motor based on the total linkage flux of the secondary windings

Control of PWM inverter output wave with reduced low‐order harmonic components

Power‐phase modifier composed of switching devices

Decoupled optimum current control of cycloconverter-induction machine system