https://eva.fing.edu.uy/pluginfile.php/55828/mod_resource/content/1/kalogiru.pdf

Solar thermal collectors and applications

Active flow control is a topic in full expansion due to associated industrial applications of huge importance, particularly for aeronautics. Among all flow control methods, such as the use of mechanical flaps, wall synthetic jets or MEMS, plasma-based devices are very promising. The main advantages of such systems are their robustness, simplicity, low power consumption and ability for real-time control at high frequency. This paper is a review of the worldwide works on this topic, from its origin to the present. It is divided into two main parts. The first one is dedicated to the recent knowledge concerning the electric wind induced by surface non-thermal plasma actuators, acting in air at atmospheric pressure. Typically, it can reach 8 m s−1 at a distance of 0.5 mm from the wall. In the second part, works concerning active airflow control by these plasma actuators are presented. Very efficient results have been obtained for low-velocity subsonic airflows (typically U∞ ≤ 30 m s−1 and Reynolds number of a few 105), and promising results at higher velocities indicate that plasma actuators could be used in aeronautics.

https://iopscience.iop.org/article/10.1088/0022-3727/40/3/S01/pdf

Airflow control by non-thermal plasma actuators

Some characteristics of air-water two-phase flow in small diameter vertical tubes

Thermal energy storage has recently attracted increasing interest related to thermal applications such as space and water heating, waste heat utilization, cooling and air-conditioning. Energy storage is essential whenever there is a mismatch between the supply and consumption of energy. Use of phase change material (PCM) capsules assembled as a packed bed is one of the important methods that has been proposed to achieve the objective of high storage density with higher efficiency. A proper designing of the thermal energy storage systems using PCMs requires quantitative information about heat transfer and phase change processes in PCM. This paper reviews the development of available latent heat thermal energy storage technologies. The different aspects of storage such as material, encapsulation, heat transfer, applications and new PCM technology innovation have been carried out.

Heat transfer characteristics of thermal energy storage system using PCM capsules: A review

We review recent advances in experimental methods for high spatial-resolution and high time-resolution thermometry, and the application of these and related methods for measurements of thermal transport in low-dimensional structures. Scanning thermal microscopy (SThM) achieves lateral resolutions of 50 nm and a measurement bandwidth of 100 kHz: SThM has been used to characterize differences in energy dissipation in single-wall and multi-wall carbon nanotubes. Picosecond thermoreflectance enables ultrahigh time-resolution in thermal diffusion experiments and characterization of heat flow across interfaces between materials; the thermal conductance G of interfaces between dissimilar materials spans a relatively small range, 20<G<200 MW m -2 K -1 near room temperature. Scanning thermoreflectance microscopy provides nanosecond time resolution and submicron lateral resolution needed for studies of heat transfer in microelectronic, optoelectronic and micromechanical systems. A fully-micromachined solid immersion lens has been demonstrated and achieves thermal-radiation imaging with lateral resolution at far below the diffraction limit, <2 μm. Microfabricated metal bridges using electrical resistance thermometry and joule heating give precise data for thermal conductivity of single crystal films, multilayer thin films, epitaxial superlattices, polycrystalline films, and interlayer dielectrics. The room temperature thermal conductivity of single crystal films of Si is strongly reduced for layer thickness below 100 nm. The through-thickness thermal conductivity of Si-Ge and GaAs-AlAs superlattices has recently been shown to be smaller than the conductivity of the corresponding alloy. The 3ω method has been recently extended to measurements of anisotropic conduction in polyimide and superlattices. Data for carbon nanotubes measured using micromachined and suspended heaters and thermometers indicate a conductivity near room temperature greater than diamond.

https://nanoheat.stanford.edu/sites/default/files/publications/A57.pdf

Thermometry and Thermal Transport in Micro/Nanoscale Solid-State Devices and Structures

The corona wind, with a velocity of several meters per second, is caused by applying high electric tension to bring about corona discharge in gases. In this paper the corona wind is experimentally and theoretically analyzed from an electrohydrod ynamical (EHD) standpoint. Experiments have been performed mainly in nitrogen by a two-dimensional electrode arrangement of a fine wire anode and a plate cathode. The voltage-current characteristics of an electrostatic probe indicate that positive ions predominate in the whole space except in an extremely narrow region close to the wire. A theoretical analysis has been conducted based on the model that positive ions produced by ionization near the wire electrode move toward the plate, introducing the bulk convective motion of neutral molecules as the result of collisions of ions and neutral molecules. The electric potential distribution in the space and pressure distribution on the plate calculated numerically agree well with the experimental data. Consequently, it is made clear that the corona wind is caused by the Coulomb force exerted on ions and collisions of ions and neutral molecules of gas.

EHD study of the corona wind between wire and plate electrodes

This paper studies the effects of gate voltage on heat generation and transport in a metal–semiconductor field effect transistor made of gallium arsenide (GaAs) with a gate length of 0.2 μm. Based on the interactions between electrons, optical phonons, and acoustic phonons in GaAs, a self‐consistent model consisting of hydrodynamic equations for electrons and phonons is developed. Concurrent study of the electrical and thermal behavior of the device shows that under a source‐to‐drain bias at 3 V and zero gate bias, the maximum electron temperature rise in this device is higher than 1000 K whereas the lattice temperature rise is of the order of 10 K, thereby exhibiting nonequilibrium characteristics. As the gate voltage is decreased from 0 to −2 V the maximum electron temperature increases due to generation of higher electric fields whereas the maximum lattice temperature reduces due to lower power dissipation. The nonequilibrium hot‐electron effect can reduce the drain current by 15% and must be included ...

Kunio Hijikata

Papers

EHD study of the corona wind between wire and plate electrodes

Effect of gate voltage on hot-electron and hot phonon interaction and transport in a submicrometer transistor

Transport phenomena of liquid CO2 in pressurized water flow with clathrate-hydrate at the interface

Active heat transfer enhancement by utilizing electric fields

Effect of dissolved gas on bubble nucleation