http://ieeexplore.ieee.org/iel5/5610941/5624686/05624745.pdf

Power electronics

Solid-state switch-mode rectification converters have reached a matured level for improving power quality in terms of power-factor correction (PFC), reduced total harmonic distortion at input AC mains and precisely regulated DC output in buck, boost, buck-boost and multilevel modes with unidirectional and bidirectional power flow. This paper deals with a comprehensive review of improved power quality converters (IPQCs) configurations, control approaches, design features, selection of components, other related considerations, and their suitability and selection for specific applications. It is targeted to provide a wide spectrum on the status of IPQC technology to researchers, designers and application engineers working on switched-mode AC-DC converters. A classified list of more than 450 research publications on the state of art of IPQC is also given for a quick reference.

/pdf/a-review-of-single-phase-improved-power-quality-ac-dc-2pm6h4zjxq.pdf

A review of single-phase improved power quality AC-DC converters

This article gives an overview of the artificial intelligence (AI) applications for power electronic systems. The three distinctive life-cycle phases, design, control, and maintenance are correlated with one or more tasks to be addressed by AI, including optimization, classification, regression, and data structure exploration. The applications of four categories of AI are discussed, which are expert system, fuzzy logic, metaheuristic method, and machine learning. More than 500 publications have been reviewed to identify the common understandings, practical implementation challenges, and research opportunities in the application of AI for power electronics. This article is accompanied by an Excel file listing the relevant publications for statistical analytics.

/pdf/an-overview-of-artificial-intelligence-applications-for-6kbutwbxvl.pdf

An Overview of Artificial Intelligence Applications for Power Electronics

Based on a survey on over 1400 commercial LED drivers and a literature review, a range of LED driver topologies are classified according to their applications, power ratings, performance and their energy storage and regulatory requirements. Both passive and active LED drivers are included in the review and their advantages and disadvantages are discussed. This paper also presents an overall view on the technical and cost aspects of the LED technology, which is useful to both researchers and engineers in the lighting industry. Some general guidelines for selecting driver topologies are included to aid design engineers to make appropriate choices.

A Survey, Classification, and Critical Review of Light-Emitting Diode Drivers

This paper proposes a novel single-stage ac-to-dc light-emitting-diode (LED) driver circuit. A buck-boost power factor (PF) corrector is integrated with a flyback converter. A recycling path is built to recover the inductive leakage energy. In this way, the presented circuit can provide not only high PF and low total harmonic distortion but also high conversion efficiency and low switching voltage spikes. Above 0.95 PF and 90% efficiency are obtained from an 8-W LED lamp driver prototype.

A Novel Single-Stage High-Power-Factor AC-to-DC LED Driving Circuit With Leakage Inductance Energy Recycling

In this paper, an integrated double buck-boost (IDBB) converter is proposed as a high-power-factor offline power supply for power-LED lamps. The IDBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains, providing high power factor and good efficiency. In this paper, the IDBB converter is analyzed, and a design methodology is proposed. It is demonstrated that, with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures can be made as high as that of the solid-state lamp. A design example for a 70-W converter supplied from a 230 V/50 Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.

Analysis and Design of the Integrated Double Buck–Boost Converter as a High-Power-Factor Driver for Power-LED Lamps

A single-phase common-mode transformerless grid-connected photovoltaic (PV) converter, which is based on the integration of two stages, is proposed in this paper. Transformer elimination in grid-connected PV systems has many advantages. It not only reduces cost, size, and weight but also increases the complete system efficiency. Since there is no galvanic isolation between grid and PV array, a leakage current may appear due to the PV parasitic capacitance to the ground, if this is not taken into account in the converter design. This paper presents a dc/dc boost converter integrated with a full-bridge inverter. The integration of these two stages reduces the ground leakage current. The neutral line of the grid is directly connected to the negative terminal of the PV array, eliminating any possibility of leakage current in this terminal. The principle of operation of the transformerless converter is analyzed, and a 200-W topology is experimentally tested.

Integrating Two Stages as a Common-Mode Transformerless Photovoltaic Converter

DC/AC converters are widely used in several applications; traditionally, they can be classified in two types: the voltage-source inverters (VSIs) and the current-source inverters (CSIs). Their use depends on their application; however, some of them are common for both types of converters. Another possibility for the dc/ac conversion is the multilevel configuration, and the most analyzed is the VSI. In this paper, a different multilevel CSI is proposed: the paralleled configuration. To control the converter, a different sinusoidal pulse with modulation is employed; it consists of modifying the reference signal instead of using multiple carriers. Additionally, a balancing method for the inductor currents is given. The operation, analysis, and implementation are presented; moreover, simulation and experimental results are shown.

A Different Multilevel Current-Source Inverter

This paper presents the analysis and experiments of a variable inductor (VI) based LED driver for dc grid lighting applications. The proposed driver requires only a series inductor and a transformer as major components to drive the LED lamp from a half-bridge inverter. By introducing a VI as the series inductor, the LED current can be controlled independently from any other parameter, which makes it possible to drive and regulate several LED branches from the same half-bridge output. Other advantages of the proposed converter include inherent open-circuit and short-circuit protections, zero-voltage switching for the bridge transistor and zero-current switching for the output rectifier diodes, simple dynamics, possibility of analog and pulse width modulation dimming, constant switching frequency operation, and high efficiency. The converter is thoroughly analyzed and modeled for both steady-state and dynamic operation. As another novelty of this paper, the dynamic response of the VI has been studied and taken into account to obtain the complete transfer function of the VI-controlled system. In addition, some housekeeping issues that usually arise when dealing with VI, e.g., how to drive the VI bias winding, are solved in this work. Experimental results provided from a 50 W laboratory prototype demonstrate the correctness of the performed analysis and the good possibilities of the proposed converter.

Analysis and Experiments on a Single-Inductor Half-Bridge LED Driver With Magnetic Control

In this paper the quadratic buck-boost (QBB) converter is proposed as a high-power-factor off-line power supply for power-LED lamps. The QBB converter features just one controlled switch and two inductors and is able to supply a solid-state lamp from the mains providing high power factor and good efficiency. In the paper, the QBB converter is analyzed and a design methodology is proposed. It is demonstrated that with a careful design of the converter, the filter capacitances can be made small enough so that film capacitors may be used. In this way, the converter mean time between failures (MTBF) can be made as high as that of the solid-state lamp. A design example for a 70W converter supplied from a 230V/50Hz mains for street lighting applications is shown. Finally, experimental results from a laboratory prototype are also presented.

R. Osorio

Papers

Analysis and Design of the Integrated Double Buck–Boost Converter as a High-Power-Factor Driver for Power-LED Lamps

Integrating Two Stages as a Common-Mode Transformerless Photovoltaic Converter

A Different Multilevel Current-Source Inverter

Analysis and Experiments on a Single-Inductor Half-Bridge LED Driver With Magnetic Control

Analysis and design of the quadratic buck-boost converter as a high-power-factor driver for power-LED lamps