In-service structural health monitoring (SHM) of engineering structures has assumed a significant role in assessing their safety and integrity. Fibre Bragg grating (FBG) sensors have emerged as a reliable, in situ, non-destructive tool for monitoring, diagnostics and control in civil structures. The versatility of FBG sensors represents a key advantage over other technologies in the structural sensing field. In this article, the recent research and development activities in structural health monitoring using FBG sensors have been critically reviewed, highlighting the areas where further work is needed. A few packaging schemes for FBG strain sensors are also discussed. Finally a few limitations and market barriers associated with the use of these sensors have been addressed.

Fibre Bragg gratings in structural health monitoring—Present status and applications

The properties of clean sands pertaining to shear strength and stiffness have been studied extensively. However, natural sands generally contain significant amounts of silt and/or clay. The mechanical response of such soils is different from that of clean sands. This paper addresses the effects of nonplastic fines on the small-strain stiffness and shear strength of sands. A series of laboratory tests was performed on samples of Ottawa sand with fines content in the range of 5–20% by weight. The samples were prepared at different relative densities and were subjected to various levels of mean effective consolidation stress. Most of the triaxial tests were conducted to axial strains in excess of 30%. The stress-strain responses were recorded, and the shear strength and dilatancy parameters were obtained for each fines percentage. Bender element tests performed in triaxial test samples allowed assessment of the effect of fines content on small-strain mechanical stiffness.

Shear strength and stiffness of silty sand

This paper describes recent advances in stability analysis that combine the limit theorems of classical plasticity with finite elements to give rigorous upper and lower bounds on the failure load. These methods, known as finite-element limit analysis, do not require assumptions to be made about the mode of failure, and use only simple strength parameters that are familiar to geotechnical engineers. The bounding properties of the solutions are invaluable in practice, and enable accurate limit loads to be obtained through the use of an exact error estimate and automatic adaptive meshing procedures. The methods are very general, and can deal with heterogeneous soil profiles, anisotropic strength characteristics, fissured soils, discontinuities, complicated boundary conditions, and complex loading in both two and three dimensions. A new development, which incorporates pore water pressures in finite-element limit analysis, is also described. Following a brief outline of the new techniques, stability solutions ...

Geotechnical stability analysis

Scientific approaches to pile design have advanced enormously in recent decades and yet, still, the most fundamental aspect of pile design—that of estimating the axial capacity—relies heavily upon empirical correlations. Improvements have been made in identifying the processes that occur within the critical zone of soil immediately surrounding the pile, but quantification of the changes in stress and fabric is not straightforward. This paper addresses the degree of confidence we can now place (a) on the conceptual and analytical frameworks for estimating pile capacity, and (b) on the quantitative parameters required to achieve a design. The discussion is restricted to driven piles in clays and siliceous sands, with particular attention given to extrapolating from design approaches derived for closed-ended piles of relatively small diameter to the large-diameter open-ended piles that are used routinely in the offshore industry. From a practical viewpoint, we need design approaches that minimise sensitivity...

Science and empiricism in pile foundation design

Tire shreds and tire shred  soil mixtures can be used as alternative backfill material in many geotechnical applications. The reuse of tire shreds may not only address growing environmental and ec...

/pdf/behaviour-of-tire-shred-sand-mixtures-2u9smxp58l.pdf

Behaviour of tire shred - sand mixtures

The method of initial parameters (MIP) was originally developed to solve the problem of a beam on an elastic foundation with applied concentrated forces along the span, which introduce discontinuities in the mathematical formulation of the problem. MIP is modified in this paper so that it can be used for solving the problem of a laterally loaded pile with discontinuities due to soil layering along the length of the pile. In this paper, the basis of MIP is outlined, and its use to find the deflection, slope, bending moment and shear force of laterally loaded piles is illustrated. Example problems of laterally loaded piles embedded in multi-layered soil media are provided.

Method of initial parameters for laterally loaded piles embedded in layered soils

The time-dependent increase in axial resistance (setup) of jacked or driven piles in sand is still not well understood, and its quantification remains a challenge. In this paper, a series o...

Short-Term Setup of Jacked Piles in a Calibration Chamber

The results of a direct shear and pullout testing program conducted to evaluate the interaction properties of three types of flexible geogrids having 2 cm, 5 cm and 10 cm square apertures within two types of backfill materials are presented. The first backfill material was a 5 cm nominal size tire shred fill and the second backfill material was a rubber-sand mixture consisting of a blend of 5 cm tire shreds and sand. Direct shear testing was conducted using a large direct shear box having plan dimensions of 30 cm by 30 cm and a total depth of 23 cm. Pullout tests were carried out in a large pullout box having plan dimensions of 1.2 m in length by 0.9 m in width and 0.5 m depth. Coefficients of interaction between 0.22 to 0.49 for tire shreds and 0.25 to 0.53 for rubber-sand were calculated.

Pullout testing of geogrids in tire shreds and rubber-sand

Constitutive models of particulate materials often rely on distances between the current stress state in stress space and various surfaces. Examples of these surfaces include the bounding surface and the dilatancy surface. This paper proposes a rigorous method for determination of distance to a surface in stress space. It starts by examining operations on stress variables defined in the $$\pi $$
 plane. Algorithms for determination of an image point on a surface are then presented as a function of the location of the current stress state with respect to the surface. For points within the surface, the bisection method is used; otherwise, the secant method is used. The paper shows that implementation of the proposed algorithm locates the image point on a surface in stress space with accuracy and rigor, providing an accurate measure of the distance to the surface that can be used in hardening or flow rules.

Determination of an image point on a surface based on a $$\pi $$ plane-based algorithm

When penetrometers or probes are pushed into sand, complex displacement fields, strain fields, and shear band patterns develop. Deep and shallow penetration processes in sands generate subs...

Rodrigo Salgado

Papers

Method of initial parameters for laterally loaded piles embedded in layered soils

Short-Term Setup of Jacked Piles in a Calibration Chamber

Pullout testing of geogrids in tire shreds and rubber-sand

Determination of an image point on a surface based on a $$\pi $$ plane-based algorithm

Displacements, Strains, and Shear Bands in Deep and Shallow Penetration Processes