Three-dimensional organic-inorganic perovskites have emerged as one of the most promising thin-film solar cell materials owing to their remarkable photophysical properties, which have led to power conversion efficiencies exceeding 20 per cent, with the prospect of further improvements towards the Shockley-Queisser limit for a single‐junction solar cell (33.5 per cent). Besides efficiency, another critical factor for photovoltaics and other optoelectronic applications is environmental stability and photostability under operating conditions. In contrast to their three-dimensional counterparts, Ruddlesden-Popper phases--layered two-dimensional perovskite films--have shown promising stability, but poor efficiency at only 4.73 per cent. This relatively poor efficiency is attributed to the inhibition of out-of-plane charge transport by the organic cations, which act like insulating spacing layers between the conducting inorganic slabs. Here we overcome this issue in layered perovskites by producing thin films of near-single-crystalline quality, in which the crystallographic planes of the inorganic perovskite component have a strongly preferential out-of-plane alignment with respect to the contacts in planar solar cells to facilitate efficient charge transport. We report a photovoltaic efficiency of 12.52 per cent with no hysteresis, and the devices exhibit greatly improved stability in comparison to their three-dimensional counterparts when subjected to light, humidity and heat stress tests. Unencapsulated two-dimensional perovskite devices retain over 60 per cent of their efficiency for over 2,250 hours under constant, standard (AM1.5G) illumination, and exhibit greater tolerance to 65 per cent relative humidity than do three-dimensional equivalents. When the devices are encapsulated, the layered devices do not show any degradation under constant AM1.5G illumination or humidity. We anticipate that these results will lead to the growth of single-crystalline, solution-processed, layered, hybrid, perovskite thin films, which are essential for high-performance opto-electronic devices with technologically relevant long-term stability.

High-efficiency two-dimensional Ruddlesden–Popper perovskite solar cells

Despite the impressive photovoltaic performances with power conversion efficiency beyond 22%, perovskite solar cells are poorly stable under operation, failing by far the market requirements. Various technological approaches have been proposed to overcome the instability problem, which, while delivering appreciable incremental improvements, are still far from a market-proof solution. Here we show one-year stable perovskite devices by engineering an ultra-stable 2D/3D (HOOC(CH2)4NH3)2PbI4/CH3NH3PbI3 perovskite junction. The 2D/3D forms an exceptional gradually-organized multi-dimensional interface that yields up to 12.9% efficiency in a carbon-based architecture, and 14.6% in standard mesoporous solar cells. To demonstrate the up-scale potential of our technology, we fabricate 10 × 10 cm2 solar modules by a fully printable industrial-scale process, delivering 11.2% efficiency stable for >10,000 h with zero loss in performances measured under controlled standard conditions. This innovative stable and low-cost architecture will enable the timely commercialization of perovskite solar cells. Up-scaling represents a key challenge for photovoltaics based on metal halide perovskites. Using a composite of 2D and 3D perovskites in combination with a printable carbon black/graphite counter electrode; Granciniet al., report 11.2% efficient modules stable over 10,000 hours.

/pdf/one-year-stable-perovskite-solar-cells-by-2d-3d-interface-3uapzy45tv.pdf

One-Year stable perovskite solar cells by 2D/3D interface engineering

Although power conversion efficiency (PCE) of state-of-the-art perovskite solar cells has already exceeded 20%, photo- and/or moisture instability of organolead halide perovskite have prevented further commercialization. In particular, the underlying weak interaction of organic cations with surrounding iodides due to eight equivalent orientations of the organic cation along the body diagonals in unit cell and chemically non-inertness of organic cation result in photo- and moisture instability of organometal halide perovskite. Here, a perovskite light absorber incorporating organic–inorganic hybrid cation in the A-site of 3D APbI3 structure with enhanced photo- and moisture stability is reported. A partial substitution of Cs+ for HC(NH2)2+ in HC(NH2)2PbI3 perovskite is found to substantially improve photo- and moisture stability along with photovoltaic performance. When 10% of HC(NH2)2+ is replaced by Cs+, photo- and moisture stability of perovskite film are significantly improved, which is attributed to the enhanced interaction between HC(NH2)2+ and iodide due to contraction of cubo-octahedral volume. Moreover, trap density is reduced by one order of magnitude upon incorporation of Cs+, which is responsible for the increased open-circuit voltage and fill factor, eventually leading to enhancement of average PCE from 14.9% to 16.5%.

Formamidinium and Cesium Hybridization for Photo- and Moisture-Stable Perovskite Solar Cell

Perovskite solar cells (PSCs) with efficiencies greater than 20% have been realized only with expensive organic hole-transporting materials. We demonstrate PSCs that achieve stabilized efficiencies exceeding 20% with copper(I) thiocyanate (CuSCN) as the hole extraction layer. A fast solvent removal method enabled the creation of compact, highly conformal CuSCN layers that facilitate rapid carrier extraction and collection. The PSCs showed high thermal stability under long-term heating, although their operational stability was poor. This instability originated from potential-induced degradation of the CuSCN/Au contact. The addition of a conductive reduced graphene oxide spacer layer between CuSCN and gold allowed PSCs to retain >95% of their initial efficiency after aging at a maximum power point for 1000 hours under full solar intensity at 60°C. Under both continuous full-sun illumination and thermal stress, CuSCN-based devices surpassed the stability of spiro-OMeTAD–based PSCs.

https://science.sciencemag.org/content/sci/early/2017/09/27/science.aam5655.full.pdf

Perovskite solar cells with CuSCN hole extraction layers yield stabilized efficiencies greater than 20

Organic and inorganic hybrid perovskites (e.g., CH(3)NH(3)PbI(3)), with advantages of facile processing, tunable bandgaps, and superior charge-transfer properties, have emerged as a new class of revolutionary optoelectronic semiconductors promising for various applications. Perovskite solar cells constructed with a variety of configurations have demonstrated unprecedented progress in efficiency, reaching about 20% from multiple groups after only several years of active research. A key to this success is the development of various solution-synthesis and film-deposition techniques for controlling the morphology and composition of hybrid perovskites. The rapid progress in material synthesis and device fabrication has also promoted the development of other optoelectronic applications including light-emitting diodes, photodetectors, and transistors. Both experimental and theoretical investigations on organic-inorganic hybrid perovskites have enabled some critical fundamental understandings of this material system. Recent studies have also demonstrated progress in addressing the potential stability issue, which has been identified as a main challenge for future research on halide perovskites. Here, we review recent progress on hybrid perovskites including basic chemical and crystal structures, chemical synthesis of bulk/nanocrystals and thin films with their chemical and physical properties, device configurations, operation principles for various optoelectronic applications (with a focus on solar cells), and photophysics of charge-carrier dynamics. We also discuss the importance of further understanding of the fundamental properties of hybrid perovskites, especially those related to chemical and structural stabilities.

Organic–inorganic hybrid lead halide perovskites for optoelectronic and electronic applications

The stability of encapsulated planar-structured CH3NH3PbI3 (MAPbI3) perovskite solar cells (PSCs) was investigated under various simulated environmental conditions. The tests were performed under approximately one sun (100 mW cm−2) illumination, varying temperature (up to 85 °C cell temperature) and humidity (up to 80%). The application of advanced sealing techniques improved the device stability, but all devices showed significant degradation after prolonged aging at high temperature and humidity. The degradation mechanism was studied by post-mortem analysis of the disassembled cells using SEM and XRD. This revealed that the degradation was mainly due to the decomposition of MAPbI3, as a result of reaction with H2O, and the subsequent reaction of hydroiodic acid, formed during MAPbI3 decomposition, with the silver back contact electrode layer.

Degradation observations of encapsulated planar CH3NH3PbI3 perovskite solar cells at high temperatures and humidity

Improving the stability and understanding the degradation mechanisms of dye-sensitized solar cells (DSSCs) are essential for their commercialization and wide-spread use. Degradation mechanisms of DSSCs built on conductive glass substrates have been studied extensively, but very few studies have been carried out on cells built on flexible plastic substrates. Here we report the photovoltaic characteristics of flexible DSSCs, using TiO2 working electrodes on ITO/PEN films prepared by cold isostatic compression at different pressures, and their analysis using electrochemical impedance spectroscopy. The degradation mechanisms of the devices were investigated through long-term aging tests by exposing the DSSCs to indoor light at room temperature. Aging of these flexible DSSCs resulted in a widened potential difference between the conduction band potential of the TiO2 (Ec) and the Nernst potential of the redox couple (Ered), and reductions in recombination resistance and effective electron diffusion length due to gradual loss of particle contacts. In general, it was found that the compression technique can only improve the short-term photovoltaic performance of the devices. Their long-term stability does not depend on the compression pressure used and all the devices were gradually degraded due to reduced particle–particle contacts and particle-conductive layer contacts. These findings provide insights and directions towards the development of more stable, flexible DSSCs.

Photovoltaic characteristics and stability of flexible dye-sensitized solar cells on ITO/PEN substrates

Flexible dye-sensitized solar cells (DSSCs) built on plastic substrates have attracted great interest as they are lightweight and can be roll-to-roll printed to accelerate production and reduce cost. However, plastic substrates such as PEN and PET are permeable to water, oxygen and volatile electrolyte solvents, which is detrimental to the cell stability. Therefore, to address this problem, in this work, an ionic liquid (IL) electrolyte is used to replace the volatile solvent electrolyte. The initial IL-based devices only achieved around 50% of the photovoltaic conversion efficiency of the cells using the solvent electrolyte. Current-voltage and electrochemical impedance spectroscopy (EIS) analysis of the cells in the dark indicated that this lower efficiency mainly originated from (i) a lack of blocking layer to reduce recombination, and (ii) a lower charge collection efficiency. To combat these problems, cells were developed using a 12 nm thick blocking layer, produced by atomic layer deposition, and 1 μm thick P25 TiO2 film sensitized with the hydrophobic MK-2 dye. These flexible DSSCs utilizing an IL electrolyte exhibit significantly improved efficiencies and a <10% drop in performance after 1000 h aging at 60°C under continuous light illumination.

Yu Han

Papers

Degradation observations of encapsulated planar CH3NH3PbI3 perovskite solar cells at high temperatures and humidity

Photovoltaic characteristics and stability of flexible dye-sensitized solar cells on ITO/PEN substrates

Improved Efficiency and Stability of Flexible Dye Sensitized Solar Cells on ITO/PEN Substrates Using an Ionic Liquid Electrolyte