Journal ArticleDOI
A study of surface texturing of carbon steel by photochemical machining
Jinyu Zhang,Yonggang Meng +1 more
TLDR
In this article, a series of experiments were carried out in the two stages of this process, photolithography and wet chemical etching, and it was found that the mixture solution of HNO3:H3PO4:H2O = 8.5:59.5%:32% (mass percentage) is a suitable etchant for the wetchemical etching of carbon steel.About:
This article is published in Journal of Materials Processing Technology.The article was published on 2012-10-01. It has received 68 citations till now. The article focuses on the topics: Photochemical machining & Isotropic etching.read more
Citations
More filters
Journal ArticleDOI
A critical assessment of surface texturing for friction and wear improvement
TL;DR: In this paper, the effects of surface textures under the operative lubrication regimes in the Stribeck curve, with a clear distinction between conformal-and non-conformal contacts, are discussed.
Journal ArticleDOI
Some innovative surface texturing techniques for tribological purposes
H.L. Costa,Ian M. Hutchings +1 more
TL;DR: In this paper, the authors present methods for texturing surfaces for tribological applications and present some innovative methods that could make surface texturing more cost-effective, but they do not discuss the cost of these methods.
Journal ArticleDOI
Direct Observation of Cavitation Phenomenon and Hydrodynamic Lubrication Analysis of Textured Surfaces
Jinyu Zhang,Yonggang Meng +1 more
TL;DR: In this paper, a comparison between experiment and simulation results has been carried out on parallel thrust bearings in terms of cavitation zone morphology in a groove, friction coefficient, and bearing clearance.
Journal ArticleDOI
Performance of Lubricated Rolling/Sliding Concentrated Contacts With Surface Textures: A Review
TL;DR: In this paper, the authors summarized the information available related to the preparation of surface textures and performance outcomes in the presence of surface texture at the concentrated contacts, and reviewed the current status of research in the area and outlining the future prospects.
Journal ArticleDOI
Micromanufacturing technologies of compact heat exchangers for hypersonic precooled airbreathing propulsion: A review
TL;DR: In this article, a review of the precooling schemes of combined cycle propulsions and key issues in the fabrication of a compact heat exchanger for HPCCE is presented.
References
More filters
Journal ArticleDOI
State of the art in Laser Surface Texturing
TL;DR: In this paper, the authors present the state of the art in LST and the potential of this technology in various lubricated applications like mechanical seals, piston rings and thrust bearings.
Proceedings ArticleDOI
State of the Art in Laser Surface Texturing
TL;DR: Laser Surface Texturing (LST) is probably the most advanced surface texturing technique as mentioned in this paper and it produces a very large number of micro-dimples on the surface and each of these microdimples can serve either as a micro-hydrodynamic bearing in cases of full or mixed lubrication.
Book
Principles of Lithography
TL;DR: The second edition of this book as discussed by the authors was written to address several needs, and the revisions for the second edition were made with those original objectives in mind, and many new topics have been included in this text commensurate with the progress that has taken place during the past few years, and several subjects are discussed in more detail.
Journal ArticleDOI
Influence of surface texture on boundary lubricated sliding contacts
TL;DR: The friction and wear behavior of boundary lubricated sliding surfaces is influenced by the surface texture as mentioned in this paper, by introducing controlled depressions and undulations in an otherwise flat surface, the...
Journal ArticleDOI
A Laser Surface Textured Parallel Thrust Bearing
TL;DR: In this article, the potential use of a new technology of laser surface texturing (LST) in parallel thrust bearings is theoretically investigated, where the surface texture has the form of micro-dimples with pre-selected diameter, depth, and area density.
Related Papers (5)
Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions
H.L. Costa,Ian M. Hutchings +1 more