Journal ArticleDOI
Influence of Cu addition on microstructure and hardness of near-eutectic Al-Si-xCu-alloys
Reads0
Chats0
TLDR
In this article, the influence of Cu content on the microstructure and hardness of near-eutectic Al-Si-xCu (x = 2, 3, 4% and 5%) was investigated.About:
This article is published in Transactions of Nonferrous Metals Society of China.The article was published on 2011-08-01. It has received 73 citations till now. The article focuses on the topics: Eutectic system & Melting point.read more
Citations
More filters
Journal ArticleDOI
Fundamentals of Physical Metallurgy
TL;DR: Theoretical Structural Metallurgy By Prof. A. H. Cottrell as discussed by the authors is a seminal work in the field of structural metal engineering. Pp. viii + 251.25s.
Journal ArticleDOI
The influence of Sr, Mg and Cu addition on the microstructural properties of a secondary AlSi9Cu3(Fe) die casting alloy
TL;DR: In this paper, the influence of Sr, Mg and Cu content on the microstructure of a high-pressure die cast AlSi9Cu3(Fe) alloy is reported.
Journal ArticleDOI
High- and low-cycle fatigue influence of silicon, copper, strontium and iron on hypo-eutectic Al-Si-Cu and Al-Si-Mg cast alloys used in cylinder heads
TL;DR: In this paper, an ambient condition fatigue investigation with different types of AlSi7Mg cast alloys in rotating-bending high-cycling fatigue (HCF) and push-pull low-cycle fatigue (LCF) regimes have been performed with varying Si, Cu, Fe and Sr contents.
Journal ArticleDOI
Influence of injection temperature and pressure on the microstructure, mechanical and corrosion properties of a AlSiCu alloy processed by HPDC
TL;DR: In this article, the effect of injection temperature and pressure on the microstructure, tensile properties and corrosion behavior of the hypoeutectic AlSi9Cu3(Fe) alloy (EN AC 46000) was also evaluated.
Journal ArticleDOI
Thermo-mechanical fatigue influence of copper and silicon on hypo-eutectic Al–Si–Cu and Al–Si–Mg cast alloys used in cylinder heads
TL;DR: In this paper, different hypo-eutectic Al-Si cast alloys with varying silicon, copper and iron contents were tested under thermo-mechanical fatigue (TMF) conditions to achieve a unified approach to damaging and fatigue endurance behavior.
References
More filters
Book
Fundamentals of Physical Metallurgy
TL;DR: In this article, the authors present a review of Free-Energy Composition Diagrams (FECD) and a comparison with Massive Transformations (MT) for fcc and hcp materials.
Journal ArticleDOI
Age-hardening behavior of cast Al–Si base alloy
TL;DR: In this paper, double aging peaks are present in the age-hardening curves of Al-Si base alloys and the first peak is higher than the second one when aged at temperature above a certain temperature.
Journal ArticleDOI
Correlation between mechanical properties and amount of dendritic α-Al phase in as-cast near-eutectic Al–11.6% Si alloys modified with strontium
TL;DR: In this article, the amount of dendritic α-Al phase with varying Sr content in near-eutectic Al-11.6% Si alloy was measured by quantitative metallography analysis software.
Journal ArticleDOI
Fundamentals of Physical Metallurgy
TL;DR: Theoretical Structural Metallurgy By Prof. A. H. Cottrell as discussed by the authors is a seminal work in the field of structural metal engineering. Pp. viii + 251.25s.
Journal ArticleDOI
Wear behaviour of eutectic and hypereutectic Al-Si-Cu-Mg casting alloys tested against a composite brake pad
L. Lasa,Jose M. Rodriguez-Ibabe +1 more
TL;DR: In this paper, wear resistance of nine eutectic and hypereutective Al-Si alloys with various compositions and processing routes was studied using a pin-on-disc configuration and two different testing speeds.
Related Papers (5)
Effect of copper and solidification conditions on the microstructure and mechanical properties of Al–Si–Mg alloys
S.G. Shabestari,H. Moemeni +1 more