Journal ArticleDOI
The effect of process parameter on the properties of spot welded cold deformed AISI304 grade austenitic stainless steel
Reads0
Chats0
TLDR
In this paper, the effect of weld time and the influence of different weld atmospheres in the resistance spot weldability of AISI304 grade stainless steel deformed in tension by 5, 10, or 20 was analyzed.About:
This article is published in Journal of Materials Processing Technology.The article was published on 2009-04-21. It has received 43 citations till now. The article focuses on the topics: Weldability & Spot welding.read more
Citations
More filters
Journal ArticleDOI
Microstructure and corrosion behavior of multipass gas tungsten arc welded 304L stainless steel
TL;DR: In this article, the effect of single pass and multipass (double and triple pass) gas tungsten arc welding (GTAW) on microstructure, hardness and corrosion behavior of 304L stainless steel was discussed.
Journal ArticleDOI
Effect of welding speed on microstructures, mechanical properties and corrosion behavior of GTA-welded AISI 201 stainless steel sheets
TL;DR: In this article, three welding speeds designated as low (1.5mm/s), medium (2.5 mm/s) and high (3.5 millimeters/sec) were operated during gas tungsten arc welding (GTAW) process and joints made were subjected to analysis of the microstructures, mechanical and corrosion properties of the joints.
Journal ArticleDOI
Cold deformation effect on the microstructures and mechanical properties of AISI 301LN and 316L stainless steels
Paulo Maria de Oliveira Silva,Paulo Maria de Oliveira Silva,Hamilton Ferreira Gomes de Abreu,Victor Hugo C. de Albuquerque,Pedro de Lima Neto,João Manuel R. S. Tavares +5 more
TL;DR: In this paper, a microstructural characterization of AISI 301LN and 316L steels was made using various techniques such as metallography, optical microscopy, scanning electronic microscopy and atomic force microscopy.
Journal ArticleDOI
Artificial neural networks for pitting potential prediction of resistance spot welding joints of AISI 304 austenitic stainless steel
TL;DR: In this article, the influence of welding process on pitting corrosion behavior of resistance spot welding joints of AISI 304 austenitic stainless steel (ASS) is estimated from the pitting potential, which is predicted from three RSW parameters.
Journal ArticleDOI
Microstructure, Texture, and Mechanical Property Analysis of Gas Metal Arc Welded AISI 304 Austenitic Stainless Steel
TL;DR: In this article, the effect of welding parameters on microstructure, texture, and mechanical properties of gas metal arc welded AISI 304 austenitic stainless steel sheet (as received) of 4 mm thickness was investigated.
References
More filters
Book
Handbook Of Stainless Steels
TL;DR: Handbook of stainless steels, Handbook of Stainless Steels as mentioned in this paper, Handbook of Stochastic Graphite and Graphite Graphite (HGPG), 2015, p.
Book
Metallurgy of Welding
TL;DR: The effect of surface forces on the bonding of materials was studied in this article. But the authors focused on the behavior of welds in service and did not consider the effects of the weld thermal cycle.
BookDOI
Resistance welding : fundamentals and applications
Hongyan Zhang,Jacek Senkara +1 more
TL;DR: WELDING METALLURGY Solidification in Resistance Spot Welding Phase Transformations in RSW Cracking References ELECTROTHERMAL Processes of WELDING Introduction Electrical Characteristics of Resistance Welding Thermal Characteristics and Electrode Life Lobe Diagrams References WELD DISCONTINUITIES Classification of Discontinuities as mentioned in this paper.
Journal ArticleDOI
Effect of weld nugget size on overload failure mode of resistance spot welds
TL;DR: In this article, an analytical model was proposed to predict failure mode and to estimate minimum nugget diameter (critical diameter) to ensure pullout failure mode in shear tensile test.
Journal ArticleDOI
Microstructure and failure behavior of dissimilar resistance spot welds between low carbon galvanized and austenitic stainless steels
TL;DR: In this article, the relationship between failure mode and weld fusion zone characteristics (size and microstructure) was studied and it was found that spot weld strength in the pullout failure mode is controlled by the strength and fusion zone size of the galvanized steel side.