Type of torsion of thin walled section ?
Best insight from top research papers
Torsion of thin-walled sections can be classified into different types based on the specific characteristics of the structures. One type is uniform torsion, where the warping displacement and angle of twist rate remain constant in all cross-sections . Another type is non-uniform torsion, which occurs when the beam is assigned with boundary conditions, resulting in varying angle of twist rate and axial displacement along the axis . Additionally, there is torsion of closed thin-walled (CTW) beams, which considers the warping deformation and restrained shear stresses on the cross section . Furthermore, shear buckling stresses in torsion of thin-walled square beams can be determined theoretically, taking into account the finite length of the beam . Lastly, an approximate analytical method has been developed for the torsion analysis of thin- to moderately thick-walled functionally graded open-section members with uniform thickness .
Answers from top 4 papers
More filters
| Papers (4) | Insight |
|---|---|
| The paper discusses the shear buckling stress in torsion of thin-walled square cross-section beams. It does not specifically mention the type of torsion. | |
15 Citations | The paper discusses the torsion of closed thin-walled (CTW) beams subjected to restrained torsion. |
11 Citations | The paper presents a novel theory of torsion of thin-walled beams with influence of shear. The type of torsion discussed in the paper is torsion of thin-walled beams. |
| The paper discusses both uniform and non-uniform torsion in thin-walled structures. |
Related Questions
How to excite torsion mode on pipe for non-destructive testing?4 answersThe torsion mode on a pipe can be excited for non-destructive testing using various methods. One approach is to use guided wave ultrasonic testing (GWUT) with a T(0,1) mode. This mode is preferred because it is nondispersive and can be generated using an array of d35 piezoelectric actuators attached around the pipe circumference. Another method is to use an array of fundamental torsional mode electromagnetic acoustic transducers (EMATs). By optimizing the element connections of the EMAT array, the T(0,1) mode can be generated and detected in the pipe. Additionally, a piezoelectric transducer with curved surface transduction plate units can be used to excite and receive the T(0,1) mode. These methods provide effective ways to excite the torsion mode on a pipe for non-destructive testing.
How can torsion be minimized in beams?3 answersTorsion in beams can be minimized through various methods. One common approach is the use of lateral bracings. These bracings help prevent lateral torsional buckling and increase the torsional resistance of the beam. Another method is the use of side plates, which can also enhance the torsional resistance of I-shaped steel beams. Additionally, the inclusion of a cover plate at the beam end can strengthen it and prevent premature failure. Another factor to consider is the design of the beam itself, such as using a pretwisted beam or considering the effects of Poisson's ratio. Overall, a combination of proper bracing, design considerations, and the use of side plates or cover plates can help minimize torsion in beams.
What is the effect of torsion on the mechanical properties of endodontic files?5 answersTorsion has an effect on the mechanical properties of endodontic files. The torsional resistance of files made of shape memory alloys is influenced by their design. The flexibility and torsional resistance of rotary files made of different alloys, such as M-wire, controlled memory (CM), R-phase, and NiTi, were compared. Metallurgical improvement of rotary files resulted in increased flexibility and torsional resistance. The torsional properties of stainless steel (SS) and nickel-titanium (NiTi) endodontic files were compared, and while the rotation to failure differed between the two materials, the actual force required to cause failure was the same. Machined endodontic files exhibited less ductility than twisted files prior to fracture and may be more susceptible to torsional failure. Overall, the torsion applied to endodontic files affects their mechanical behavior, including flexibility, torsional resistance, and rotation to failure.
What is the rate of torsion in pcos?5 answersTesticular torsion is a condition that can occur in males, causing severe pain and potential damage to the testes. The rate of torsion varies depending on the population studied. In a study conducted in Lagos, Nigeria, the rate of testicular torsion was found to be 35 cases per year, with a mean age of 23.3 years. Another study in Nigeria reported a low salvage rate of 32% for clinically viable testes, which was attributed to delayed or mistaken diagnosis. However, the abstracts provided do not specifically mention the rate of torsion in individuals with polycystic ovary syndrome (PCOS). Therefore, further research is needed to determine the specific rate of testicular torsion in individuals with PCOS.
What are the applications of torsional pendulums?5 answersTorsional pendulums have various applications. They are widely used in physical experiments due to their small restoring forces, which make them suitable for measuring tiny forces. One application is in low-frequency gravity gradiometers, where the low resonant frequencies of torsion pendulums allow for good response to the fluctuation of the local gravity field at low frequencies. Another application is in gravitational experiments, where torsion pendulums are used as weak force sensitive instruments to measure the gravitational torque between source and test-mass assemblies. Additionally, torsion pendulums combined with electrostatic springs have been proposed to improve the measurement sensitivity of angular deflection, which is useful for gravitational experiments with higher precision requirements. Torsion pendulums are also used in educational laboratory settings to study damping torsion oscillations and understand concepts such as angular momentum and mechanical energy conservation laws.
How does the torsional pendulum work?3 answersThe torsional pendulum works by measuring the gravitational torque between source and test-mass assemblies using two methods. In the Cavendish method, the pendulum moves freely, while in the electrostatic-servo method, the pendulum is maintained at a constant angle by applying an electrostatic torque equal and opposite to any gravitational torque on the pendulum. The electrostatic torque is generated by a servo. The design and implementation of this servo have been described in papers by Schlamminger et al.and Citation Text. The electrostatic-servo method utilizes a digital servo loop with a Kalman filter to achieve measurement performance comparable to an open loop. The use of three electrodes for feedback control allows for small measurement uncertainty. The torsional pendulum technique based on image processing, as developed by Yu et al., allows for the measurement of the torsional oscillation of individual fibers.