In this paper, a basic cell for low-power and/or low-voltage operation is identified. It is evidenced how different versions of this cell, coined as "flipped voltage follower (FVF)" have been used in the past for many applications. A detailed classification of basic topologies derived from the FVF is given. In addition, a comprehensive list of recently proposed low-voltage/low-power CMOS circuits based on the FVF is given. Although the paper has a tutorial taste, some new applications of the FVF are also presented and supported by a set of simulated and experimental results. Finally, a design example showing the application of the FVF to build systems based on translinear loops is described which shows the potential of this cell for the design of high-performance low-power/low-voltage analog and mixed-signal circuits.

The flipped voltage follower: a useful cell for low-voltage low-power circuit design

Random device mismatch plays an important role in the design of accurate analog circuits. Models for the matching of MOS and bipolar devices from open literature show that matching improves with increasing device area. As a result, accuracy requirements impose a minimal device area and this paper explores the impact of this constraint on the performance of general analog circuits. It results in a fixed bandwidth-accuracy-power tradeoff which is set by technology constants. This tradeoff is independent of bias point for bipolar circuits whereas for MOS circuits some bias point optimizations are possible. The performance limitations imposed by matching are compared to the limits imposed by thermal noise. For MOS circuits the power constraints due to matching are several orders of magnitude higher than for thermal noise. For the bipolar case the constraints due to noise and matching are of comparable order of magnitude. The impact of technology scaling on the conclusions of this work are briefly explored.

Device mismatch and tradeoffs in the design of analog circuits

We present design techniques that make possible the operation of analog circuits with very low supply voltages, down to 0.5 V. We use operational transconductance amplifier (OTA) and filter design as a vehicle to introduce these techniques. Two OTAs, one with body inputs and the other with gate inputs, are designed. Biasing strategies to maintain common-mode voltages and attain maximum signal swing over process, voltage, and temperature are proposed. Prototype chips were fabricated in a 0.18-/spl mu/m CMOS process using standard 0.5-V V/sub T/ devices. The body-input OTA has a measured 52-dB DC gain, a 2.5-MHz gain-bandwidth, and consumes 110 /spl mu/W. The gate-input OTA has a measured 62-dB DC gain (with automatic gain-enhancement), a 10-MHz gain-bandwidth, and consumes 75 /spl mu/W. Design techniques for active-RC filters are also presented. Weak-inversion MOS varactors are proposed and modeled. These are used along with 0.5-V gate-input OTAs to design a fully integrated, 135-kHz fifth-order elliptic low-pass filter. The prototype chip in a 0.18-/spl mu/m CMOS process with V/sub T/ of 0.5-V also includes an on-chip phase-locked loop for tuning. The 1-mm/sup 2/ chip has a measured dynamic range of 57 dB and draws 2.2 mA from the 0.5-V supply.

0.5-V analog circuit techniques and their application in OTA and filter design

In this paper, a 10-bit 1-GSample/s current-steering CMOS digital-to-analog (D/A) converter is presented. The measured integral nonlinearity is better than /spl plusmn/0.2 LSB and the measured differential nonlinearity lies between -0.08 and 0.14 LSB proving the 10-bit accuracy. The 1-GSample/s conversion rate has been obtained by an, at transistor level, fully custom-designed thermometer decoder and synchronization circuit. The layout has been carefully optimized. The parasitic interconnect loads have been estimated and have been iterated in the circuit design. A spurious-free dynamic range (SFDR) of more than 61 dB has been measured in the interval from dc to Nyquist. The power consumption equals 110 mW for a near-Nyquist sinusoidal output signal at a 1-GHz clock. The chip has been processed in a standard 0.35-/spl mu/m CMOS technology and has an active area of only 0.35 mm/sup 2/.

A 10-bit 1-GSample/s Nyquist current-steering CMOS D/A converter

CMOS Data Converters for Communications distinguishes itself from other data converter books by emphasizing system-related aspects of the design and frequency-domain measures. It explains in detail how to derive data converter requirements for a given communication system (baseband, passband, and multi-carrier systems). The authors also review CMOS data converter architectures and discuss their suitability for communications. The rest of the book is dedicated to high-performance CMOS data converter architecture and circuit design. Pipelined ADCs, parallel ADCs with an improved passive sampling technique, and oversampling ADCs are the focus for ADC architectures, while current-steering DAC modeling and implementation are the focus for DAC architectures. The principles of the switched-current and the switched-capacitor techniques are reviewed and their applications to crucial functional blocks such as multiplying DACs and integrators are detailed. The book outlines the design of the basic building blocks such as operational amplifiers, comparators, and reference generators with emphasis on the practical aspects. To operate analog circuits at a reduced supply voltage, special circuit techniques are needed. Low-voltage techniques are also discussed in this book. CMOS Data Converters for Communications can be used as a reference book by analog circuit designers to understand the data converter requirements for communication applications. It can also be used by telecommunication system designers to understand the difficulties of certain performance requirements on data converters. It is also an excellent resource to prepare analog students for the new challenges ahead.

CMOS Data Converters for Communications

A 12-bit intrinsic accuracy digital-to-analog (D/A) converter integrated in a standard digital 0.5 /spl mu/m CMOS technology is presented. It is based on a current steering doubly segmented 6+2+4 architecture and requires no calibration, no trimming, or dynamic averaging. The differential nonlinearity (DNL) and integral nonlinearity (INL) are 0.3 and 0.6 least significant bits (LSB's), respectively. The measured glitch energy is 1.9 pV.s. For a 12-bit resolution, the converter reaches an update rate of 300 MS/s. By reducing the voltage supply of the latches to 2.0 V, the glitch energy is reduced to sub-pV.s, and the update rate reaches 500 MS/s, for a resolution of 8 bits. The worst case power consumption is 320 mW, and it operates from a single 3.3 V voltage supply. The die area is 3.2 mm/sup 2/.

A 12-bit intrinsic accuracy high-speed CMOS DAC

The design of a low-voltage and low-power /spl Delta//spl Sigma/ analog-to-digital (A/D) converter is presented. A third-order single-loop /spl Delta//spl Sigma/ modulator topology is implemented with the differential modified switched op-amp technique. The modulator topology has been transformed as to accommodate half-delay integrators. Dedicated low-voltage circuit building blocks, such as a class AB operational transconductance amplifier, a common-mode feedback amplifier, and a comparator are treated, as well as low-voltage design techniques. The influence of very low supply voltage on power consumption is discussed. Measurement results of the 900-mV /spl Delta//spl Sigma/ A/D converter show a 77-dB dynamic range in a 16-kHz bandwidth and a 62-dB peak signal-to-noise ratio for a 40-/spl mu/W power consumption.

A 900-mV low-power /spl Delta//spl Sigma/ A/D converter with 77-dB dynamic range

A systematic study of single-loop, cascaded, and multibit /spl Delta//spl Sigma/ modulators of second to fourth order is presented, based on a combination of behavioral simulations and linear modeling. Constraints for optimal performance and precise guidelines for the choice of parameters are derived. Moreover, the optimal parameters and the corresponding performance are found and given in tables. A graph showing the maximal achievable performance of each topology as a function of the oversampling ratio is presented, offering a valuable help for the design of analog-to-digital converters.

Optimal parameters for /spl Delta//spl Sigma/ modulator topologies

The design of a high-resolution, high-speed, delta-sigma analog to-digital converter that operates from a single 3.3-V supply is presented. This supply voltage presents several design problems, such as reduced signal swing and nonzero switch resistance in the switched-capacitor circuits. These problems are tackled in this design by a careful optimization at the system level and by a detailed analysis of several circuit nonidealities. The converter uses a 2-1-1 cascade topology with optimized coefficients. For an oversampling-ratio of only 24, the converter achieves a signal-to-noise ratio of 87 dB, a signal-to-(noise+distortion) ratio of 82 dB, and an input dynamic range of 15 bits after comb filtering. The converter is sampled at 52.8 MHz, which results in the required signal bandwidth for asymmetrical digital subscriber line applications of 1.1 MHz. It is implemented in a 0.5-/spl mu/m CMOS technology, in a 5-mm/sup 2/ die area, and consumes 200 mW from a 3.3-V power supply.

A 3.3-V, 15-bit, delta-sigma ADC with a signal bandwidth of 1.1 MHz for ADSL applications

The design of a low-voltage and low-power analog-to-digital (A/D) converter is presented. A third-order single-loop modulator topology is implemented with the differential modified switched op-amp technique. The modulator topology has been transformed as to accommodate half-delay integrators. Dedicated low-voltage circuit building blocks, such as a class AB operational transconductance amplifier, a common- mode feedback amplifier, and a comparator are treated, as well as low-voltage design techniques. The influence of very low supply voltage on power consumption is discussed. Measurement results of the 900-mV A/D converter show a 77-dB dynamic range in a 16-kHz bandwidth and a 62-dB peak signal-to-noise ratio for a 40- W power consumption.

Augusto M. Marques

Papers

A 12-bit intrinsic accuracy high-speed CMOS DAC

A 900-mV low-power /spl Delta//spl Sigma/ A/D converter with 77-dB dynamic range

Optimal parameters for /spl Delta//spl Sigma/ modulator topologies

A 3.3-V, 15-bit, delta-sigma ADC with a signal bandwidth of 1.1 MHz for ADSL applications

Converter with 77-dB Dynamic Range