Fast pyrolysis utilizes biomass to produce a product that is used both as an energy source and a feedstock for chemical production. Considerable efforts have been made to convert wood biomass to liquid fuels and chemicals since the oil crisis in mid-1970s. This review focuses on the recent developments in the wood pyrolysis and reports the characteristics of the resulting bio-oils, which are the main products of fast wood pyrolysis. Virtually any form of biomass can be considered for fast pyrolysis. Most work has been performed on wood, because of its consistency and comparability between tests. However, nearly 100 types of biomass have been tested, ranging from agricultural wastes such as straw, olive pits, and nut shells to energy crops such as miscanthus and sorghum. Forestry wastes such as bark and thinnings and other solid wastes, including sewage sludge and leather wastes, have also been studied. In this review, the main (although not exclusive) emphasis has been given to wood. The literature on woo...

Pyrolysis of Wood/Biomass for Bio-oil: A Critical Review

In this review, we summarize the knowledge of the production and properties of charcoal that has been accumulated over the past 38 millenia. The manipulation of pressure, moisture content, and gas flow enables biomass carbonization with fixed-carbon yields that approachor attainthe theoretical limit after reaction times of a few tens of minutes. Much of the heat needed to carbonize the feed is released by vigorous, exothermic secondary reactions that reduce the formation of unwanted tars by augmenting the charcoal yield in a well-designed carbonizer. As a renewable fuel, charcoal has many attractive features:  it contains virtually no sulfur or mercury and is low in nitrogen and ash; it is highly reactive yet easy to store and handle. Carbonized charcoal can be a good adsorbent with a large surface area and a semimetal with an electrical resistivity comparable to that of graphite. Recent advances in knowledge about the production and properties of charcoal presage its expanded use as a renewable fuel, red...

/pdf/the-art-science-and-technology-of-charcoal-production-2yxzbuvb7k.pdf

The Art, Science, and Technology of Charcoal Production†

The characterization of activated carbons with oxygen and nitrogen surface groups

Multiwalled carbon nanotube-supported Pt (Pt/MWNT) nanocomposites were prepared by both the aqueous solution reduction of a Pt salt (HCHO reduction) and the reduction of a Pt ion salt in ethylene glycol solution. For comparison, a Pt/XC-72 nanocomposite was also prepared by the EG method. The Pt/MWNT catalyst prepared by the EG method has a high and homogeneous dispersion of spherical Pt metal particles with a narrow particle-size distribution. TEM images show that the Pt particle size is in the range of 2-5 nm with a peak at 2.6 nm, which is consistent with 2.5 nm obtained from the XRD broadening calculation. Surface chemical modifications of MWNTs and water content in EG solvent are found to be the key factors in depositing Pt particles on MWNTs. In the case of the direct methanol fuel cell (DMFC) test, the Pt/MWNT catalyst prepared by EG reduction is slightly superior to the catalyst prepared by aqueous reduction and displays significantly higher performance than the Pt/XC-72 catalyst. These differences in catalytic performance between the MWNT-supported or the carbon black XC-72-supported catalysts are attributed to a greater dispersion of the supported Pt particles when the EG method is used, in contrast to aqueous HCHO reduction and to possible unique structural and higher electrical properties when contrasting MWNTs to carbon black XC-72 as a support.

Preparation and Characterization of Multiwalled Carbon Nanotube-Supported Platinum for Cathode Catalysts of Direct Methanol Fuel Cells

To increase their electrochemically active surface area, catalysts supported on high surface area materials, commonly carbons, are widely used in low-temperature fuel cells. Recent studies have revealed that the physical properties of the carbon support can greatly affect the electrochemical properties of the fuel cell catalyst. It has been reported that carbon materials with both high surface area and good crystallinity can not only provide a high dispersion of Pt nanoparticles, but also facilitate electron transfer, resulting in better device performance. On this basis, novel non-conventional carbon materials have attracted much interest as electrocatalyst support because of their good electrical and mechanical properties and their versatility in pore size and pore distribution tailoring. These materials present a different morphology than carbon blacks both at the nanoscopic level in terms of their pore texture (for example mesopore carbon) and at the macroscopic level in terms of their form (for example microsphere). The examples are supports produced from ordered mesoporous carbons, carbon aerogels, carbon nanotubes, carbon nanohorns, carbon nanocoils and carbon nanofibers. The challenge is to develop carbon supports with high surface area, good electrical conductivity, suitable porosity to allow good reactant flux, and high stability in fuel cell environment, utilizing synthesis methods simple and not too expensive. This paper presents an overview of carbon supports for Pt-based catalysts, with particular attention on new carbon materials. The effect of substrate characteristics on catalyst properties, as electrocatalytic activity and stability in fuel cell environment, is discussed.

Carbon supports for low-temperature fuel cell catalysts

Electrical conductivity of conductive carbon blacks: influence of surface chemistry and topology

Electrical conductivity of thermal carbon blacks: Influence of surface chemistry

The vacuum pyrolysis of used tires

The vacuum pyrolysis of used tires enables the recovery of useful products, such as pyrolytic oil and pyrolytic carbon black (CB{sub P}). The light part of the pyrolytic oil contains dl-limonene which has a high price on the market. The naphtha fraction can be used as a high octane number component for gasoline. The middle distillate demonstrated mechanical and lubricating properties similar to those of the commercial aromatic oil Dutrex R 729. The heavy oil was tested as a feedstock for the production of needle coke. It was found that the surface morphology of CB{sub P} produced by vacuum pyrolysis resembles that of commercial carbon black. The CB{sub P} contains a higher concentration of inorganic compounds (especially ZnO and S) than commercial carbon black. The pyrolysis process feasibility looks promising. One old tire can generate upon vacuum pyrolysis, incomes of at least $2.25 US with a potential of up to $4.83 US/tire upon further product improvement. The process has been licensed to McDermott Marketing Servicing Inc. (Houston) for its exploitation in the US.

Hans Darmstadt

Papers

Electrical conductivity of conductive carbon blacks: influence of surface chemistry and topology

Electrical conductivity of thermal carbon blacks: Influence of surface chemistry

The vacuum pyrolysis of used tires

Vacuum pyrolysis of used tires

Surface chemistry of ordered mesoporous carbons