There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality.

Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

I and i

다중혈관 관상동맥 환자에서 y-문합을 이용하여 양쪽 내흉동맥만을 사용한 우회술의 조기 성적

Friction stir welding (FSW) is a relatively new solid-state joining process. This joining technique is energy efficient, environment friendly, and versatile. In particular, it can be used to join high-strength aerospace aluminum alloys and other metallic alloys that are hard to weld by conventional fusion welding. FSW is considered to be the most significant development in metal joining in a decade. Recently, friction stir processing (FSP) was developed for microstructural modification of metallic materials. In this review article, the current state of understanding and development of the FSW and FSP are addressed. Particular emphasis has been given to: (a) mechanisms responsible for the formation of welds and microstructural refinement, and (b) effects of FSW/FSP parameters on resultant microstructure and final mechanical properties. While the bulk of the information is related to aluminum alloys, important results are now available for other metals and alloys. At this stage, the technology diffusion has significantly outpaced the fundamental understanding of microstructural evolution and microstructure–property relationships.

/pdf/friction-stir-welding-and-processing-3hu3ejo7ub.pdf

Friction Stir Welding and Processing

Metals have been mankind's most essential materials for thousands of years; however, their use is affected by ecological and economical concerns Alloys with higher strength and ductility could alleviate some of these concerns by reducing weight and improving energy efficiency However, most metallurgical mechanisms for increasing strength lead to ductility loss, an effect referred to as the strength-ductility trade-off Here we present a metastability-engineering strategy in which we design nanostructured, bulk high-entropy alloys with multiple compositionally equivalent high-entropy phases High-entropy alloys were originally proposed to benefit from phase stabilization through entropy maximization Yet here, motivated by recent work that relaxes the strict restrictions on high-entropy alloy compositions by demonstrating the weakness of this connection, the concept is overturned We decrease phase stability to achieve two key benefits: interface hardening due to a dual-phase microstructure (resulting from reduced thermal stability of the high-temperature phase); and transformation-induced hardening (resulting from the reduced mechanical stability of the room-temperature phase) This combines the best of two worlds: extensive hardening due to the decreased phase stability known from advanced steels and massive solid-solution strengthening of high-entropy alloys In our transformation-induced plasticity-assisted, dual-phase high-entropy alloy (TRIP-DP-HEA), these two contributions lead respectively to enhanced trans-grain and inter-grain slip resistance, and hence, increased strength Moreover, the increased strain hardening capacity that is enabled by dislocation hardening of the stable phase and transformation-induced hardening of the metastable phase produces increased ductility This combined increase in strength and ductility distinguishes the TRIP-DP-HEA alloy from other recently developed structural materials This metastability-engineering strategy should thus usefully guide design in the near-infinite compositional space of high-entropy alloys

Metastable high-entropy dual-phase alloys overcome the strength–ductility trade-off

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

The structural changes in a 304-type austenitic stainless steel during large strain cold rolling and subsequent annealing were studied. The severe deformation resulted in the development of highly elongated grains/subgrains aligned along the rolling axis. The transverse grain/subgrain size rapidly decreased to its minimal value of about 50 nm at relatively small strains of ~1 and then hardly changed upon following deformation. Such a structural response on cold working was associated with multiple twinning resulting in fast grain subdivision. The processing was accompanied by a partial martensitic transformation resulting in a decrease of austenite volume fraction to about 0.35 after straining to e = 4.0. Isochronal annealing for 30 min was characterised by a gradual coarsening of grains, the average size of which increased to about 200 nm after heating to 800°C. The high elongation of ferrite grains facilitated simultaneous homogeneous nucleation of austenite grains throughout the matrix upon heating; and, therefore, promoted the development of ultrafine grained structure with the size of structural elements well below 1 micron.

Ultrafine Grain Evolution in Austenitic Stainless Steel during Large Strain Deformation and Subsequent Annealing

PURPOSE: P-added steel is prepared which has high strength, simple process to refine a particle size of ferrite. CONSTITUTION: The steel comprises less than 0.3 % of carbon, less than 0.5 % of silicon, less than 3.0 % of manganese, less than 0.02 % of sulfur, Fe and 0.04- 0.1 weight % of phosphor having average particle size of less than 3 micrometer ferrite. Thus, 0.1 weight % of phosphor is added in a high frequency melted material containing Fe, 0.1 weight % of carbon, 0.3 weight % of silicon, 1.5 weight % of manganese. The steel is gamma-treated at 1,173 K for 60 seconds, cooling to 1,23 K to 10 K/second velocity and compressed-distorted.

High strength p-added steel and preparing it

Feinkorniger ferritischer Baustahl und Herstellungsverfahren dieses Stahles

A high strength phosphorus-containing steel having fine texture, which is a carbon steel having an average ferritic grain diameter of 3 mu m or less and containing from 0.04 to 0.1% by mass of P, wherein the volume fraction of P segregated in the grain boundary is 0.3 or less when the grain boundary is covered by a layer 1 nm in thickness.

Method o0f producing a high strength phosphorus-containing steel.

The creep behavior of oxide-bearing Fe-0.6%O steel was studied in the temperature range of 550-700°C at stresses ranging from 100 to 400 MPa. The creep data showed high values of an apparent stress exponent n close to 16 for power-law creep. In addition the apparent experimental activation energy was much higher than that for the lattice diffusion in -iron. Analysis of creep data revealed that the deformation behavior was strongly affected by the threshold stresses, which are associated with the interaction between moving dislocations and fine incoherent oxide particles. Analysis of deformation behavior in terms of threshold stress leads the true stress exponent of 8; the activation energy for creep became close to value of activation energy for lattice diffusion at 700°C and for pipe-diffusion in the temperature range of 550–650°C.

Kaneaki Tsuzaki

Papers

Ultrafine Grain Evolution in Austenitic Stainless Steel during Large Strain Deformation and Subsequent Annealing

High strength p-added steel and preparing it

Feinkorniger ferritischer Baustahl und Herstellungsverfahren dieses Stahles

Method o0f producing a high strength phosphorus-containing steel.

Creep behavior of an oxide dispersion strengthened iron with ultrafine grain structure