There is, I think, something ethereal about i —the square root of minus one. I remember first hearing about it at school. It seemed an odd beast at that time—an intruder hovering on the edge of reality.

Usually familiarity dulls this sense of the bizarre, but in the case of i it was the reverse: over the years the sense of its surreal nature intensified. It seemed that it was impossible to write mathematics that described the real world in …

I and i

This paper addresses to some of the latest contributions on the application of Finite Control Set Model Predictive Control (FCS-MPC) in Power Electronics. In FCS-MPC , the switching states are directly applied to the power converter, without the need of an additional modulation stage. The paper shows how the use of FCS-MPC provides a simple and efficient computational realization for different control objectives in Power Electronics. Some applications of this technology in drives, active filters, power conditioning, distributed generation and renewable energy are covered. Finally, attention is paid to the discussion of new trends in this technology and to the identification of open questions and future research topics.

State of the Art of Finite Control Set Model Predictive Control in Power Electronics

This paper presents a comprehensive study on the state-of-the-art and emerging wind energy technologies from the electrical engineering perspective. In an attempt to decrease cost of energy, increase the wind energy conversion efficiency, reliability, power density, and comply with the stringent grid codes, the electric generators and power electronic converters have emerged in a rigorous manner. From the market based survey, the most successful generator-converter configurations are addressed along with few promising topologies available in the literature. The back-to-back connected converters, passive generator-side converters, converters for multiphase generators, and converters without intermediate dc-link are investigated for high-power wind energy conversion systems (WECS), and presented in low and medium voltage category. The onshore and offshore wind farm configurations are analyzed with respect to the series/parallel connection of wind turbine ac/dc output terminals, and high voltage ac/dc transmission. The fault-ride through compliance methods used in the induction and synchronous generator based WECS are also discussed. The past, present and future trends in megawatt WECS are reviewed in terms of mechanical and electrical technologies, integration to power systems, and control theory. The important survey results, and technical merits and demerits of various WECS electrical systems are summarized by tables. The list of current and future wind turbines are also provided along with technical details.

High-Power Wind Energy Conversion Systems: State-of-the-Art and Emerging Technologies

Rapid advances in industrial information integration methods have spurred tremendous growth in the use of enterprise systems. Consequently, a variety of techniques have been used for probing enterprise systems. These techniques include business process management, workflow management, Enterprise Application Integration (EAI), Service-Oriented Architecture (SOA), grid computing, and others. Many applications require a combination of these techniques, which is giving rise to the emergence of enterprise systems. Development of the techniques has originated from different disciplines and has the potential to significantly improve the performance of enterprise systems. However, the lack of powerful tools still poses a major hindrance to exploiting the full potential of enterprise systems. In particular, formal methods and systems methods are crucial for modeling complex enterprise systems, which poses unique challenges. In this paper, we briefly survey the state of the art in the area of enterprise systems as they relate to industrial informatics.

Enterprise Systems: State-of-the-Art and Future Trends

The aim of this paper is to review the state-of-the-art of Field Programmable Gate Array (FPGA) technologies and their contribution to industrial control applications. Authors start by addressing various research fields which can exploit the advantages of FPGAs. The features of these devices are then presented, followed by their corresponding design tools. To illustrate the benefits of using FPGAs in the case of complex control applications, a sensorless motor controller has been treated. This controller is based on the Extended Kalman Filter. Its development has been made according to a dedicated design methodology, which is also discussed. The use of FPGAs to implement artificial intelligence-based industrial controllers is then briefly reviewed. The final section presents two short case studies of Neural Network control systems designs targeting FPGAs.

https://hal-centralesupelec.archives-ouvertes.fr/hal-01337007/document

FPGAs in Industrial Control Applications

This article presents the benefits of using field-programmable gate array (FPGA)-based controllers for power electronics and drive applications. For this purpose, an algorithm perspective is first proposed, where it is stated that, depending on the intrinsic parallelism properties as well as level of complexity, it makes sense to implement each control algorithm on a specific hardware and/or software architecture to get the best performances in terms of execution time or the best ratio performance versus cost. Then, an application perspective is proposed where the constraints specifically linked to the control of power converters are discussed.

FPGA-based Controllers

The aim of this paper is to present a fully integrated solution for synchronous motor control. The implemented controller is based on Actel Fusion field-programmable gate array (FPGA). The objective of this paper is to evaluate the ability of the proposed fully integrated solution to ensure all the required performances in such applications, particularly in terms of control quality and time/area performances. To this purpose, a current control algorithm of a permanent-magnet synchronous machine has been implemented. This machine is associated with a resolver position sensor. In addition to the current control closed loop, all the necessary motor control tasks are implemented in the same device. The analog-to-digital conversion is ensured by the integrated analog-to-digital converter (ADC), avoiding the use of external converters. The resolver processing unit, which computes the rotor position and speed from the resolver signals, is implemented in the FPGA matrix, avoiding the use of external resolver-to-digital converter (RDC). The sine patterns used for the Park transformation are stored in the integrated flash memory blocks.

Fully Integrated FPGA-Based Controller for Synchronous Motor Drive

The aim of this paper is to quantify the interest of using hardware field-programmable gate arrays (FPGAs) to implement complex control algorithms. As a benchmark, authors have chosen a sensorless speed controller for a synchronous motor. The estimation of the rotor position and speed is achieved using an extended Kalman filter (EKF), eliminating the need of their corresponding mechanical sensors. Due to the EKF complexity, such sensorless controller is systematically implemented in a software digital signal processor (DSP) device. The execution time is frequently evaluated to several tens or hundreds of microseconds. The motivation here is to prove that, when exploiting the treatment fastness of FPGAs (less than 6 μs ), it is possible to enhance the control bandwidth. To reach this objective, a comparison between the developed FPGA-based sensorless speed controller and its DSP-based counterpart is made. The same sensorless controller (with the same complexity) has been implemented in both cases. To prop up this comparison, simulation, hardware-in-the-loop, and experimental tests are presented.

/pdf/fully-fpga-based-sensorless-control-for-synchronous-ac-drive-23jx578ve6.pdf

Fully FPGA-Based Sensorless Control for Synchronous AC Drive Using an Extended Kalman Filter

This paper deals with embedded real-time (RT) simulators applied in power electronic applications and implemented in low-cost field-programmable gate arrays. Indeed, such simulators' intellectual properties (IPs) are not only intended for hardware-in-the-loop (HIL) testing but also can be advantageously embedded within digital controllers to ensure functions such as observation, estimation, diagnostic, or health monitoring. Conversely, to the HIL case, the main challenge when designing such simulators' IPs is to cope with their complexity having in mind that, in the case of embedded systems, the available hardware resources are limited due to the cost. Furthermore, this challenge is strengthened by the need of very short simulation time steps that is typically the case when simulating power converters. By this way, this paper presents the design of an embedded RT simulator of a three-phase grid-connected voltage-source rectifier, based on the associated discrete circuit modeling approach. This IP is associated with the one of a three-phase $RL$ filter, and both are implemented within the rectifier controller to estimate the grid currents. The latter is injected in the controller when a fault is detected in the current sensors. The ability of this estimator to guarantee the service continuity in case of faults has been validated through HIL tests and experiments.

ADC-Based Embedded Real-Time Simulator of a Power Converter Implemented in a Low-Cost FPGA: Application to a Fault-Tolerant Control of a Grid-Connected Voltage-Source Rectifier

L. Idkhajine

Papers

FPGAs in Industrial Control Applications

FPGA-based Controllers

Fully Integrated FPGA-Based Controller for Synchronous Motor Drive

Fully FPGA-Based Sensorless Control for Synchronous AC Drive Using an Extended Kalman Filter

ADC-Based Embedded Real-Time Simulator of a Power Converter Implemented in a Low-Cost FPGA: Application to a Fault-Tolerant Control of a Grid-Connected Voltage-Source Rectifier