The role of extended and point defects, and key impurities such as C, O, and H, on the electrical and optical properties of GaN is reviewed. Recent progress in the development of high reliability contacts, thermal processing, dry and wet etching techniques, implantation doping and isolation, and gate insulator technology is detailed. Finally, the performance of GaN-based electronic and photonic devices such as field effect transistors, UV detectors, laser diodes, and light-emitting diodes is covered, along with the influence of process-induced or grown-in defects and impurities on the device physics.

Gan : processing, defects, and devices

Gallium oxide (Ga2O3) is emerging as a viable candidate for certain classes of power electronics, solar blind UV photodetectors, solar cells, and sensors with capabilities beyond existing technologies due to its large bandgap. It is usually reported that there are five different polymorphs of Ga2O3, namely, the monoclinic (β-Ga2O3), rhombohedral (α), defective spinel (γ), cubic (δ), or orthorhombic (e) structures. Of these, the β-polymorph is the stable form under normal conditions and has been the most widely studied and utilized. Since melt growth techniques can be used to grow bulk crystals of β-GaO3, the cost of producing larger area, uniform substrates is potentially lower compared to the vapor growth techniques used to manufacture bulk crystals of GaN and SiC. The performance of technologically important high voltage rectifiers and enhancement-mode Metal-Oxide Field Effect Transistors benefit from the larger critical electric field of β-Ga2O3 relative to either SiC or GaN. However, the absence of clear demonstrations of p-type doping in Ga2O3, which may be a fundamental issue resulting from the band structure, makes it very difficult to simultaneously achieve low turn-on voltages and ultra-high breakdown. The purpose of this review is to summarize recent advances in the growth, processing, and device performance of the most widely studied polymorph, β-Ga2O3. The role of defects and impurities on the transport and optical properties of bulk, epitaxial, and nanostructures material, the difficulty in p-type doping, and the development of processing techniques like etching, contact formation, dielectrics for gate formation, and passivation are discussed. Areas where continued development is needed to fully exploit the properties of Ga2O3 are identified.

A review of Ga2O3 materials, processing, and devices

Roughened surfaces of light-emitting diodes (LEDs) provide substantial improvement in light extraction efficiency. By using the laser-lift-off technique followed by an anisotropic etching process to roughen the surface, an n-side-up GaN-based LED with a hexagonal “conelike” surface has been fabricated. The enhancement of the LED output power depends on the surface conditions. The output power of an optimally roughened surface LED shows a twofold to threefold increase compared to that of an LED before surface roughening.

Increase in the extraction efficiency of GaN-based light-emitting diodes via surface roughening

Recent research results pertaining to InN, GaN and AlN are reviewed, focusing on the different growth techniques of Group III-nitride crystals and epitaxial films, heterostructures and devices. The chemical and thermal stability of epitaxial nitride films is discussed in relation to the problems of deposition processes and the advantages for applications in high-power and high-temperature devices. The development of growth methods like metalorganic chemical vapour deposition and plasma-induced molecular beam epitaxy has resulted in remarkable improvements in the structural, optical and electrical properties. New developments in precursor chemistry, plasma-based nitrogen sources, substrates, the growth of nucleation layers and selective growth are covered. Deposition conditions and methods used to grow alloys for optical bandgap and lattice engineering are introduced. The review is concluded with a description of recent Group III-nitride semiconductor devices such as bright blue and white light-emitting diodes, the first blue-emitting laser, high-power transistors, and a discussion of further applications in surface acoustic wave devices and sensors.

https://iopscience.iop.org/article/10.1088/0022-3727/31/20/001/pdf

Growth and applications of Group III-nitrides

To study the effects of plasma chemistries on etch characteristics and plasma-induced damage to the optical properties, dry etching of ZnO films has been carried out using inductively coupled plasmas of Cl2/Ar, Cl2/H2/Ar, and CH4/H2/Ar. The CH4/H2/Ar chemistry showed a faster etch rate and a better surface morphology than the Cl2-based chemistries. Etched samples in all chemistries showed a substantial decrease in the PL intensity of band-edge luminescence mainly due to the plasma-induced damage. The CH4/H2/Ar chemistry showed the least degradation of the optical properties.

/pdf/dry-etching-of-zno-films-and-plasma-induced-damage-to-2djixydcey.pdf

Dry etching of ZnO films and plasma-induced damage to optical properties

The reverse breakdown voltage of p-GaN Schottky diodes was used to measure the electrical effects of high density Ar or H2 plasma exposure. The near surface of the p-GaN became more compensated through introduction of shallow donor states whose concentration depended on ion flux, ion energy, and ion mass. At high fluxes or energies, the donor concentration exceeded 1019 cm−3 and produced p-to-n surface conversion. The damage depth was established as ∼400 A based on electrical and wet etch rate measurements. Rapid thermal annealing at 900 °C under a N2 ambient restored the initial electrical properties of the p-GaN.

Electrical effects of plasma damage in p-GaN

GaN Schottky diodes were exposed to N2 or H2 inductively coupled plasmas prior to deposition of the rectifying contact. Subsequent annealing, wet photochemical etching, or (NH4)2S surface passivation treatments were examined for their effect on diode current–voltage (I–V) characteristics. We found that either annealing at 750 °C under N2, or removal of ∼500–600 A of the surface essentially restored the initial I–V characteristics. There was no measurable improvement in the plasma-exposed diode behavior with (NH4)2S treatments.

/pdf/depth-and-thermal-stability-of-dry-etch-damage-in-gan-3iyn2cwp35.pdf

Depth and thermal stability of dry etch damage in GaN Schottky diodes

A GaN/AlGaN heterojunction bipolar transistor structure with Mg doping in the base and Si Doping in the emitter and collector regions was grown by Metal Organic Chemical Vapor Deposition in c-axis Al(2)O(3). Secondary Ion Mass Spectrometry measurements showed no increase in the O concentration (2-3x10(18) cm(-3)) in the AlGaN emitter and fairly low levels of C (~4-5x10(17) cm (-3)) throughout the structure. Due to the non-ohmic behavior of the base contact at room temperature, the current gain of large area (~90 um diameter) devices was <3. Increasing the device operating temperature led to higher ionization fractions of the mg acceptors in the base, and current gains of ~10 were obtained at 300 degree C.

/pdf/growth-and-fabrication-of-gan-algan-heterojunction-bipolar-1khinhszkz.pdf

Growth and fabrication of GaN/AlGaN heterojunction bipolar transistor

Plasma-induced etch damage can degrade the electrical and optical performance of III-V nitride electronic and photonic devices. We have investigated the etch-induced damage of an Inductively Coupled Plasma (ICP) etch system on the electrical performance of mesa-isolated GaN pn-junction diodes. GaN p-i-n mesa diodes were formed by Cl{sub 2}/BCl{sub 3}/Ar ICP etching under different plasma conditions. The reverse leakage current in the mesa diodes showed a strong relationship to chamber pressure, ion energy, and plasma flux. Plasma induced damage was minimized at moderate flux conditions ({le} 500 W), pressures {ge}2 mTorr, and at ion energies below approximately -275 V.

https://digital.library.unt.edu/ark:/67531/metadc624355/m2/1/high_res_d/14382.pdf

Inductively coupled plasma-induced etch damage of GaN p-n junctions

High-density plasma etching has been an effective patterning technique for the group-III nitrides due to ion fluxes which are two to four orders of magnitude higher than more conventional reactive ion etch systems. GaN etch rates exceeding 0.5 μm/min have been reported in inductively coupled plasma (ICP) etch systems at relatively high dc-biases (>200 V). However, under these conditions, the etch mechanism is dominated by ion bombardment energies which can induce damage and minimize etch selectivity. Development of etch processes with high selectivity has become relevant with recent interest in high power, high temperature electronic devices. In this study, we report ICP etch rates and selectivities for GaN, AlN, and InN in Cl2/Ar, Cl2/N2, Cl2/H2, Cl2/SF6, BCl3/Ar, BCl3/H2, BCl3/N2, and BCl3/SF6 plasma chemistries.

L. Zhang

Papers

Electrical effects of plasma damage in p-GaN

Depth and thermal stability of dry etch damage in GaN Schottky diodes

Growth and fabrication of GaN/AlGaN heterojunction bipolar transistor

Inductively coupled plasma-induced etch damage of GaN p-n junctions

Selective inductively coupled plasma etching of group-III nitrides in Cl2- and BCl3-based plasmas