Furfural offers a promising, rich platform for lignocellulosic biofuels. These include methylfuran and methyltetrahydrofuran, valerate esters, ethylfurfuryl and ethyltetrahydrofurfuryl ethers as well as various C(10)-C(15) coupling products. The various production routes are critically reviewed, and the needs for improvements are identified. Their relative industrial potential is analysed by defining an investment index and CO(2) emissions as well as determining the fuel properties for the resulting products. Finally, the most promising candidate, 2-methylfuran, was subjected to a road trial of 90,000 km in a gasoline blend. Importantly, the potential of the furfural platform relies heavily on the cost-competitive production of furfural from lignocellulosic feedstock. Conventional standalone and emerging coproduct processes-for example, as a coproduct of cellulosic ethanol, levulinic acid or hydroxymethyl furfural-are expensive and energetically demanding. Challenges and areas that need improvement are highlighted. In addition to providing a critical review of the literature, this paper also presents new results and analysis in this area.

Furfural—A Promising Platform for Lignocellulosic Biofuels

Thermosetting (bio)materials derived from renewable resources: A critical review

Photocatalysis: a promising route for 21st century organic chemistry

Hydrogen: Trends, production and characterization of the main process worldwide

Recent advances in vegetable oil-based polymers and their composites

Epoxidation of cottonseed oil by aqueous hydrogen peroxide catalysed by liquid inorganic acids.

Coal fly ash was used to synthesize X-type zeolite by alkali fusion followed by hydrothermal treatment. The synthesized zeolite was characterized using various techniques such as X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, BET method for surface area measurement etc. The synthesis conditions were optimized to obtain highly crystalline zeolite with maximum BET surface area. The maximum surface area of the product was found to be 383 m2/g with high purity. The crystallinity of the prepared zeolite was found to change with fusion temperature and a maximum value was obtained at 823 K. The cost of synthesized zeolite was estimated to be almost one-fifth of that of commercial 13X zeolite available in the market.

/pdf/zeolite-from-fly-ash-synthesis-and-characterization-438lqqhuiy.pdf

Zeolite from fly ash: synthesis and characterization

Studies on the epoxidation of mahua oil (Madhumica indica) by hydrogen peroxide.

Canola oil with an iodine value of 112/100 g, and containing 60% oleic acid and 20% linoleic acid, was epoxidised using a peroxyacid generated in situ from hydrogen peroxide and a carboxylic acid (acetic or formic acid) in the presence of an acidic ion exchange resin (AIER), Amberlite IR 120H. Acetic acid was found to be a better oxygen carrier than formic acid, as it produced about 10% more conversion of ethylenic unsaturation to oxirane than that produced by formic acid under otherwise identical conditions. A detailed process developmental study was then performed with the acetic acid/AIER combination. The parameters optimised were temperature (65 °C), acetic acid to ethylenic unsaturation molar ratio (0.5), hydrogen peroxide to ethylenic unsaturation molar ratio (1.5), and AIER loading (22%). An iodine conversion of 88.4% and a relative conversion to oxirane of 90% were obtained at the optimum reaction conditions. The heterogeneous catalyst, AIER, was found to be reusable and exhibited a negligible loss in activity.

Narayan C. Pradhan

Papers

Epoxidation of cottonseed oil by aqueous hydrogen peroxide catalysed by liquid inorganic acids.

Zeolite from fly ash: synthesis and characterization

Studies on the epoxidation of mahua oil (Madhumica indica) by hydrogen peroxide.

Epoxidation of Canola Oil with Hydrogen Peroxide Catalyzed by Acidic Ion Exchange Resin

Kinetics of epoxidation of jatropha oil with peroxyacetic and peroxyformic acid catalysed by acidic ion exchange resin