In the previous paper Ralph Brodd and Martin Winter described the different kinds of batteries and fuel cells. In this paper I will describe lithium batteries in more detail, building an overall foundation for the papers that follow which describe specific components in some depth and usually with an emphasis on the materials behavior. The lithium battery industry is undergoing rapid expansion, now representing the largest segment of the portable battery industry and dominating the computer, cell phone, and camera power source industry. However, the present secondary batteries use expensive components, which are not in sufficient supply to allow the industry to grow at the same rate in the next decade. Moreover, the safety of the system is questionable for the large-scale batteries needed for hybrid electric vehicles (HEV). Another battery need is for a high-power system that can be used for power tools, where only the environmentally hazardous Ni/ Cd battery presently meets the requirements. A battery is a transducer that converts chemical energy into electrical energy and vice versa. It contains an anode, a cathode, and an electrolyte. The anode, in the case of a lithium battery, is the source of lithium ions. The cathode is the sink for the lithium ions and is chosen to optimize a number of parameters, discussed below. The electrolyte provides for the separation of ionic transport and electronic transport, and in a perfect battery the lithium ion transport number will be unity in the electrolyte. The cell potential is determined by the difference between the chemical potential of the lithium in the anode and cathode, ∆G ) -EF. As noted above, the lithium ions flow through the electrolyte whereas the electrons generated from the reaction, Li ) Li+ + e-, go through the external circuit to do work. Thus, the electrode system must allow for the flow of both lithium ions and electrons. That is, it must be both a good ionic conductor and an electronic conductor. As discussed below, many electrochemically active materials are not good electronic conductors, so it is necessary to add an electronically conductive material such as carbon * To whom correspondence should be addressed. Phone and fax: (607) 777-4623. E-mail: stanwhit@binghamton.edu. 4271 Chem. Rev. 2004, 104, 4271−4301

http://www.chemie.uni-regensburg.de/Anorganische_Chemie/Vortrag/StudentenWS06-07/Vortrag_Amereller.pdf

Lithium Batteries and Cathode Materials

https://las493energy.files.wordpress.com/2014/11/2005_vetter_jpowsourc.pdf

Ageing mechanisms in lithium-ion batteries

The present status and prospects for further development of polycrystalline or amorphous transparent conducting oxide (TCO) semiconductors used for practical thin-film transparent electrode applications are presented in this paper. The important TCO semiconductors are impurity-doped ZnO, In2O3 and SnO2 as well as multicomponent oxides consisting of combinations of ZnO, In2O3 and SnO2, including some ternary compounds existing in their systems. Development of these and other TCO semiconductors is important because the expanding need for transparent electrodes for optoelectronic device applications is jeopardizing the availability of indium-tin-oxide (ITO), whose main constituent, indium, is a very expensive and scarce material. Al- and Ga-doped ZnO (AZO and GZO) semiconductors are promising as alternatives to ITO for thin-film transparent electrode applications. In particular, AZO thin films, with a low resistivity of the order of 10−5 Ω cm and source materials that are inexpensive and non-toxic, are the best candidates. However, further development of the deposition techniques, such as magnetron sputtering or vacuum arc plasma evaporation, as well as of the targets is required to enable the preparation of AZO and GZO films on large area substrates with a high deposition rate.

https://iopscience.iop.org/article/10.1088/0268-1242/20/4/004/pdf

Transparent conducting oxide semiconductors for transparent electrodes

Positive electrodes for Li-ion and lithium batteries (also termed “cathodes”) have been under intense scrutiny since the advent of the Li-ion cell in 1991. This is especially true in the past decade. Early on, carbonaceous materials dominated the negative electrode and hence most of the possible improvements in the cell were anticipated at the positive terminal; on the other hand, major developments in negative electrode materials made in the last portion of the decade with the introduction of nanocomposite Sn/C/Co alloys and Si−C composites have demanded higher capacity positive electrodes to match. Much of this was driven by the consumer market for small portable electronic devices. More recently, there has been a growing interest in developing Li−sulfur and Li−air batteries that have the potential for vastly increased capacity and energy density, which is needed to power large-scale systems. These require even more complex assemblies at the positive electrode in order to achieve good properties. This r...

Positive Electrode Materials for Li-Ion and Li-Batteries†

Most research to develop highly transparent and conductive thin films has focused on n-type semiconductors consisting of metal oxides. Historically, transparent conducting oxide (TCO) thin films composed of binary compounds such as SnO2 and In2O3 were developed by means of chemical- and physical-deposition methods. Impurity-doped SnO2 (Sb- or F-doped SnO2, e.g., SnO2:Sb or SnO2: F) and In2O3: Sn (indium tin oxide, ITO) films are in practical use. In addition to binary compounds, ternary compounds such as Cd2SnO4, CdSnO3, and CdIn2O4 were developed prior to 1980, but their TCO films have not yet been used widely.

https://www.cambridge.org/core/services/aop-cambridge-core/content/view/S0883769400027159

Takashi Mouri

Papers

Preparation and properties of LiCoyMnxNi1−x−yO2 as a cathode for lithium ion batteries

Preparations of ZnO:Al transparent conducting films by d.c. magnetron sputtering

Preparation of LiyMnxNi1−xO2 as a cathode for lithium-ion batteries

Aluminium content dependence of milky transparent conducting ZnO:Al films with textured surface prepared by d.c. magnetron sputtering

Highly conductive and transparent ZnO:Al thin films prepared on high-temperature substrates by d.c. magnetron sputtering