This communication describes a simple method for patterning paper to create well-defined, millimeter-sized channels, comprising hydrophilic paper bounded by hydrophobic polymer. We believe that this type of patterned paper will become the basis for low-cost, portable, and technically simple multiplexed bioassays. We demonstrate this capability by the simultaneous detection of glucose and protein in 5 μL of urine. The assay system is small, disposable, easy to use (and carry), and requires no external equipment, reagents, or power sources. We believe this kind of system is attractive for uses in less-industrialized countries, in the field, or as an inexpensive alternative to more advanced technologies already used in clinical settings.[1-4]

The analysis of biological fluids is necessary for monitoring the health of populations,[2] but these measurements are difficult to implement in remote regions such as those found in less-industrialized countries, in emergency situations, or in home health-care settings.[3] Conventional laboratory instruments provide quantitative measurements of biological samples, but they are unsuitable for these situations since they are large, expensive, and require trained personnel and considerable volumes of biological samples.[2] Other bioassay platforms provide alternatives to more expensive instruments,[5-7] but the need remains for a platform that uses small volumes of sample and that is sufficiently inexpensive to be used widely for measuring samples from large populations.

We believe that paper may serve as a particularly convenient platform for running bioassays in the remote situations locations. As a prototype for a mthod we believe to be particularly promosing, we patterned photoresist onto chromatography paper to form defined areas of hydrophilic paper separated by hydrophobic lines or “walls”; these patterns provide spatial control of biological fluids and enable fluid transport, without pumping, due to capillary action in the millimeter-sized channels produced. This method for patterning paper makes it possible to run multiple diagnostic assays on one strip of paper, while still using only small volumes of a single sample. In a fully developed technology, patterned photoresist would be replaced by an appropriate printing technology, but patterning paper with photoresist is: i) convenient for prototyping these devices, and ii) a useful new micropatterning technology in its own right.

We patterned chromatography paper with SU-8 2010 photoresist as shown in Figure 1a and as described below: we soaked a 7.5-cm diameter piece of chromatography paper in 2 mL of SU-8 2010 for 30 s, spun it at 2000 rpm for 30 s, and then baked it at 95 °C for 5 min to remove the cyclopentanone in the SU-8 formula. We then exposed the photoresist and paper to 405 nm UV light (50 mW/cm2) for 10 s through a photo-mask (CAD/Art Services, Inc.) that was aligned using a mask aligner (OL-2 Mask Aligner, AB-M, Inc). After exposure, we baked the paper a second time at 95 °C for 5 min to cross-link the exposed portions of the resist. The unpolymerized photoresist was removed by soaking the paper in propylene glycol monomethyl ether acetate (PGMEA) (5 min), and by washing the pattern with propan-2-ol (3 × 10 mL). The paper was more hydrophobic after it was patterned, presumably due to residual resist bound to the paper, so we exposed the entire surface to an oxygen plasma for 10 s at 600 millitorr (SPI Plasma-Prep II, Structure Probe, Inc) to increase the hydrophilicity of the paper (Figures 2a and 2b).



Figure 1

Chromatography paper patterned with photoresist. The darker lines are cured photoresist; the lighter areas are unexposed paper. (a) Patterned paper after absorbing 5 μL of Waterman red ink by capillary action. The central channel absorbs the sample ...





Figure 2

Assays contaminated with (a) dirt, (b) plant pollen, and (c) graphite powder. The pictures were taken before and after running an artificial urine solution that contained 550 mM glucose and 75 μM BSA. The particulates do not move up the channels ...



The patterned paper can be derivatized for biological assays by adding appropriate reagents to the test areas (Figures 1b and ​and2b).2b). In this communication, we demonstrate the method by detecting glucose and protein,[8] but the surface should be suitable for measuring many other analytes as well.[7] The glucose assay is based on the enzymatic oxidation of iodide to iodine,[9] where a color change from clear to brown is associated with the presence of glucose.[10] The protein assay is based on the color change of tetrabromophenol blue (TBPB) when it ionizes and binds to proteins;[11] a positive result in this case is indicated by a color change from yellow to blue.

For the glucose assay, we spotted 0.3 μL of a 0.6 M solution of potassium iodide, followed by 0.3 μL of a 1:5 horseradish peroxidase/glucose oxidase solution (15 units of protein per mL of solution). For the protein assay, we spotted 0.3 μL of a 250-mM citrate buffer (pH 1.8) in a well separate from the glucose assay, and then layered 0.3 μL of a 3.3 mM solution of tetrabromophenol blue (TBPB) in 95% ethanol over the citrate buffer. The spotted reagents were allowed to air dry at room temperature. This pre-loaded paper gave consistent results for the protein assay regardless of storage temperature and time (when stored for 15 d both at 0 °C and at 23 °C, wrapped in aluminum foil). The glucose assay was sensitive to storage conditions, and showed decreased signal for assays run 24 h after spotting the reagents (when stored at 23 °C); when stored at 0 °C, however, the glucose assay was as sensitive after day 15 as it was on day 1.

We measured artificial samples of glucose and protein in clinically relevant ranges (2.5-50 mM for glucose and 0.38-7.5 μM for bovine serum albumin (BSA))[12, 13] by dipping the bottom of each test strip in 5 μL of a pre-made test solution (Figure 2d). The fluid filled the entire pattern within ca. one minute, but the assays required 10-11 min for the paper to dry and for the color to fully develop.[14] In all cases, we observed color changes corresponding roughly in intensity to the amount of glucose and protein in the test samples, where the lowest concentrations define the lower limits to which these assays can be used (Figure 2e). For comparison, commercially-available dipsticks detect glucose at concentrations as low as 5 mM[7, 9] and protein as low as 0.75 μM;[6, 15] these limits indicate that these paper-based assays are comparable in sensitivity to commercial dipstick assays. Our assay format also allows for the measurement of multiple analytes.

This paper-based assay is suitable for measuring multiple samples in parallel and in a relatively short period of time. For example, in one trial, one researcher was able to run 20 different samples (all with 550 mM glucose and 75 μM BSA) within 7.5 min (followed by another 10.5 min for the color to fully develop). An 18-min assay of this type—one capable of measuring two analytes in 20 different sample—may be efficient enough to use in high-throughput screens of larger sample pools.

In the field, samples will not be measured under sterile conditions, and dust and dirt may contaminate the assays. The combination of paper and capillary action provides a mechanism for separating particulates from a biological fluid. As a demonstration, we purposely contaminated the artificial urine samples with quantities of dirt, plant pollen, and graphite powder at levels higher than we might expect to see in the samples in the field. These particulates do not move up the channels under the action of capillary wicking, and do not interfere with the assay (Figure 3).

Paper strips have been used in biomedical assays for decades because they offer an inexpensive platform for colorimetric chemical testing.[1] Patterned paper has characteristics that lead to miniaturized assays that run by capillary action (e.g., without external pumping), with small volumes of fluids. These methods suggest a path for the development of simple, inexpensive, and portable diagnostic assays that may be useful in remote settings, and in particular, in less-industrialized countries where simple assays are becoming increasingly important for detecting disease and monitoring health,[16, 17], for environmental monitoring, in veterinary and agricultural practice and for other applications.

/pdf/patterned-paper-as-a-platform-for-inexpensive-low-volume-1csojtz6lz.pdf

Patterned Paper as a Platform for Inexpensive, Low‐Volume, Portable Bioassays

This article describes a prototype system for quantifying bioassays and for exchanging the results of the assays digitally with physicians located off-site. The system uses paper-based microfluidic devices for running multiple assays simultaneously, camera phones or portable scanners for digitizing the intensity of color associated with each colorimetric assay, and established communications infrastructure for transferring the digital information from the assay site to an off-site laboratory for analysis by a trained medical professional; the diagnosis then can be returned directly to the healthcare provider in the field. The microfluidic devices were fabricated in paper using photolithography and were functionalized with reagents for colorimetric assays. The results of the assays were quantified by comparing the intensities of the color developed in each assay with those of calibration curves. An example of this system quantified clinically relevant concentrations of glucose and protein in artificial uri...

/pdf/simple-telemedicine-for-developing-regions-camera-phones-and-4d9clsku42.pdf

Simple telemedicine for developing regions: camera phones and paper-based microfluidic devices for real-time, off-site diagnosis.

This article describes a method for fabricating 3D microfluidic devices by stacking layers of patterned paper and double-sided adhesive tape. Paper-based 3D microfluidic devices have capabilities in microfluidics that are difficult to achieve using conventional open-channel microsystems made from glass or polymers. In particular, 3D paper-based devices wick fluids and distribute microliter volumes of samples from single inlet points into arrays of detection zones (with numbers up to thousands). This capability makes it possible to carry out a range of new analytical protocols simply and inexpensively (all on a piece of paper) without external pumps. We demonstrate a prototype 3D device that tests 4 different samples for up to 4 different analytes and displays the results of the assays in a side-by-side configuration for easy comparison. Three-dimensional paper-based microfluidic devices are especially appropriate for use in distributed healthcare in the developing world and in environmental monitoring and water analysis.

/pdf/three-dimensional-microfluidic-devices-fabricated-in-layered-487blmp2vn.pdf

Three-dimensional microfluidic devices fabricated in layered paper and tape.

This article describes a point-of-care (POC) system—comprising a microfluidic, paper-based analytical device (μ-PAD) and a hand-held optical colorimeter—for quantifying the concentration of analytes in biological fluids. The μ-PAD runs colorimetric assays, and consists of paper that has been (i) patterned to expose isolated regions of hydrophilic zones and (ii) wet with an index-matching fluid (e.g., vegetable oil) that is applied using a disposable, plastic sleeve encasement. Measuring transmittance through paper represents a new method of quantitative detection that expands the potential functionality of μ-PADs. This prototype transmittance colorimeter is inexpensive, rugged, and fully self-contained, and thus potentially attractive for use in resource-limited environments and developing countries.

Quantifying Colorimetric Assays in Paper-Based Microfluidic Devices by Measuring the Transmission of Light through Paper

Contributing Authors. Preface. Acknowledgments. Chapter 1. Erythrocytes. Chapter 2. Leukocytes. Chapter 3. Hematopoietic Neoplasia. Chapter 4. Hemostasis. Chapter 5. Water, Electrolytes, and Acid Base. Chapter 6. Proteins, Lipids, and Carbohydrates. Chapter 7. Liver. Chapter 8. Digestive System. Chapter 9. Urinary System. Chapter 10. Muscle. Chapter 11. Endocrine System. Chapter 12. Cytology. Chapter 13. Generating and Interpreting Test Results: Test Validity, Quality Control, Reference Values, and Basic Epidemiology. Case Studies. Index.

Duncan & Prasse's veterinary laboratory medicine: clinical pathology.

We developed a dye-binding method for albumin in urine based on bis (3',3"-diiodo4'4"-dihydroxy-5'5"-dinitrophenyl)-3,4,5,6-tetrabr omosulfonphthalein (DIDNTB), a dye that has a higher chemical sensitivity and specificity for albumin when compared to two other commonly used dyes. We prepared urine dipsticks with DIDNTB and certain other compounds to prevent "nonspecific" binding to the dipstick matrix. The detection limit for albumin with DIDNTB as the dye is about 10 mg/L. The extent of dye binding to proteins and other compounds was studied using ultracentrifugation and a selectively permeable membrane that permitted the passage of free but not bound dye; we believe this method is superior to photometric titration. The affinity of the dyes for albumin was found to be pH dependent with stronger binding at pH 1.8 than at pH 7.0. At pH 1.8, DIDNTB had a ca.10-fold greater binding coefficient to albumin when compared to the widely used dyes, tetrabromophenol blue (CI 4430-25-5) or bromophenol blue (CI 115-39-9). We developed a system that minimized nonspecific binding by the dye through the use of polymethyl vinyl ethers and bis-(heptapropylene glycol) carbonate. DIDNTB showed a greater chemical specificity for albumin when compared to most other proteins. The new albumin dipsticks are resistant to many potential interferences at substantial concentrations, making the dipsticks suitable to screen for albuminuria.

/pdf/high-sensitivity-dye-binding-assay-for-albumin-in-urine-38gbu8jmhg.pdf

High-sensitivity dye binding assay for albumin in urine.

Assay of creatinine using the peroxidase activity of copper-creatinine complexes.

Urinary trypsin inhibitor (uTi) is a product of elastase-mediated degradation of interleukin-alpha-inhibitor (I-alpha-I). Its activity increases in the urine of patients with a malignancy, inflammation, or infection, or in late pregnancy. The objective of this study was to compare the sensitivity of uTi in urine with that of serum quantitative C-reactive protein (CRP) for diagnosing infection, as indicated by white cell response and clinical assessment. Ninety controls and 171 patients with various systemic infections were enrolled. We measured uTi enzymatically on a Cobas Fara (Roche Diagnostics). Patients were separated into bacterial, probable bacterial, viral, or probable viral groups based on the results of a complete blood count with differential (CBC), urinalysis (UA), and clinical assessment. In the bacterial (n=70) and control (n=90) groups, the uTi values (mean+/-SE) were 25.3+/-3.1 mg/L and 2.8+/-0.8 mg/L, respectively. uTi (at 2.7 mg/L) had a diagnostic sensitivity of 91% and specificity of 82% (AUC=0.889), whereas CRP (at a cutoff of 10 mg/L) had a sensitivity and specificity of 82% and 96%, respectively (AUC=0.921). As a marker of infection (positive in both bacterial and viral groups), uTi had a sensitivity of 91% (AUC=0.884) vs. 89% (AUC=0.828) for CRP. Our data indicate that uTi has sufficient clinical sensitivity for screening systemic infections, and may have diagnostic value as a noninvasive test.

/pdf/sensitive-noninvasive-marker-for-the-diagnosis-of-probable-1epw1zyuro.pdf

Sensitive noninvasive marker for the diagnosis of probable bacterial or viral infection.

Clinical utility of a rapid test for uristatin.

Disclosed is an improved assay for the determination of total protein in an aqueous test fluid such as urine The assay involves combining the test fluid with a molybdate or tungstate salt and a dye which forms a complex with molybdate or tungstate ion at a pH of 10 to 30 to shift the absorption band of the complex in the presence of protein There is introduced into the assay a substituted phenolsulfonephthalein dye having a pKa which enables it to operate at a pH of from about 10 to 30 and whose affinity for protein is such that it will provide a detectable response only in the presence of greater than 50 mg/dL of protein to increase the scope of the assay

Todd K. Cast

Papers

High-sensitivity dye binding assay for albumin in urine.

Assay of creatinine using the peroxidase activity of copper-creatinine complexes.

Sensitive noninvasive marker for the diagnosis of probable bacterial or viral infection.

Clinical utility of a rapid test for uristatin.

Total protein detection method