Showing papers in "Materials Science and Engineering in 1966"

TL;DR: In this article, negative strain-rate sensitivity is shown to be a common feature in a variety of materials provided test conditions are chosen such that serrated yielding (the Portevin-Le Chatelier effect) occurs.

TL;DR: In this article, the radial distribution function is used to establish a corresponding states correlation of the configurational heat capacities of six low-melting metals, and it is suggested that this correlation may be used to estimate the configural contribution to the specific heats of other liquid metals.

TL;DR: In this article, a single source technique was used to vacuum deposit epitaxial Sn1−xPbxTe films, and the same lattice constant lattice was maintained to within the experimental error of two parts in 6000.

TL;DR: Debye-Scherrer methods have been employed to determine the structure of a metastable transition product which forms during the decomposition of a quenched aluminum-29 at.% zinc alloy.

TL;DR: Using non-linear elasticity theory, calculations of the amplitudes of second harmonics generated in a cubic solid by finite amplitude ultrasonic waves of different polarization and propagation vectors in a {110} type plane have been made.

TL;DR: In this paper, a mikromagnetische Theorie entwickelt, den Einfluβ innerer Spannungen auf reversible Magnetisierungsprozesse voll beruckichtigt.

TL;DR: In this article, X-ray diffraction patterns from wire-drawn 70:30 brass and Si-bronze alloys were used to obtain residual stresses (σ), deformation textures, stacking-fault probabilities (α), domain sizes (De(hkl)) and r.m.s.

TL;DR: In this paper, an 95% gewalztem Kupfer mittels elektronenmikroskopischer Feinbereichs beugung bestimmten Orientierungen of 560 Stellen werden quantitativ nach folgenden Gesichtspunkten ausgewertet.

TL;DR: In this paper, a slip-induced directional order analysis for the B2-type superlattices has been developed for both long and short-range order in the structure, as well as for nearest-neighbor and next-nearest neighbor interactions.

TL;DR: In this paper, a technique for obtaining Poisson's ratio for materials undergoing large strains has been developed, where the change in volume of a specimen is measured during a compression test which allows specimen volume to be obtained as a function of compressive strain in the specimen.

TL;DR: In this paper, the kombinierten Magnetisierungsprozeβ “Wandbewegungen and Drehungen” erfolgt.

TL;DR: The grossflachige Versetzungsanordnung is in wesentlichen durch die Vorzugsstellung der Primargleitebene (Schichten, Gitter, Versetungsgruppen) sowie der Ebene senkrecht zur primargleitrichtung (Wande) gekennzeichnet as discussed by the authors.

TL;DR: The role of surfaces in defect nucleation, the various types of defects, and the various nucleation mechanisms are described in a review of growth and perfection in thin films and the structural defects therein this paper.

TL;DR: In this article, the authors investigated the sintering of single crystal rutile spheres in air and in reducing atmosphere in the temperature range 900 to 1350°C and concluded that surface diffusion is the transport process controlling sinter.

TL;DR: In this paper, a mechanism by which conditions of plastic anisotropy, relatively high machining temperatures and loading from spark discharge machining interact to produce this damage is proposed.

TL;DR: In this article, a polycrystalline Cu-2% Co alloy, overaged at 600°C to produce a fine dispersion of coherent particles, was severely deformed by swaging and then annealed.

TL;DR: In this article, the dielectric constant and loss factor of the following mixtures have been studied near room temperature as a function of frequency in the microwave region: (1) nitrobenzene and o-nitrotoluene in n-dodecane in concentrations of 0.1, 0.2 and 0.3 mole fraction of each of the polar components.

TL;DR: In this paper, the X-ray reflections from specimens of high-purity copper, deformed to various amounts by rolling at room temperature, have been analyzed by Fourier methods to determine the size and strain broadening components.

TL;DR: In this article, the shapes and positions of X-ray reflections from a specimen of high-purity copper, prepared from material which had been rolled to produce maximum Xray line broadening, have been examined both while the specimen was under tensile stress and in the unloaded condition.