scispace - formally typeset
Journal ArticleDOI

Effects of Large Scale High Freestream Turbulence and Exit Reynolds Number on Turbine Vane Heat Transfer in a Transonic Cascade

TLDR
In this article, the effects of large scale high freestream turbulence intensity and exit Reynolds number on the surface heat transfer distribution of a turbine vane in a 2D linear cascade at realistic engine Mach numbers were investigated.
Abstract
This paper experimentally and numerically investigates the effects of large scale high freestream turbulence intensity and exit Reynolds number on the surface heat transfer distribution of a turbine vane in a 2D linear cascade at realistic engine Mach numbers. A passive turbulence grid was used to generate a freestream turbulence level of 16% and integral length scale normalized by the vane pitch of 0.23 at the cascade inlet. The base line turbulence level and integral length scale normalized by the vane pitch at the cascade inlet were measured to be 2% and 0.05, respectively. Surface heat transfer measurements were made at the midspan of the vane using thin film gauges. Experiments were performed at exit Mach numbers of 0.55, 0.75, and 1.01, which represent flow conditions below, near, and above nominal conditions. The exit Mach numbers tested correspond to exit Reynolds numbers of 910 5 , 1.0510 6 , and 1.510 6 based on a vane chord. The experimental results showed that the large scale high freestream turbulence augmented the heat transfer on both the pressure and suction sides of the vane as compared to the low freestream turbulence case and promoted a slightly earlier boundary layer transition on the suction surface for exit Mach 0.55 and 0.75. At nominal conditions, exit Mach 0.75, average heat transfer augmentations of 52% and 25% were observed on the pressure and suction sides of the vane, respectively. An increased Reynolds number was found to induce an earlier boundary layer transition on the vane suction surface and to increase heat transfer levels on the suction and pressure surfaces. On the suction side, the boundary layer transition length was also found to be affected by increase changes in Reynolds number. The experimental results also compared well with analytical correlations and computational fluid dynamics predictions. DOI: 10.1115/1.2952381

read more

Citations
More filters
Journal ArticleDOI

Direct Numerical Simulations of a High-Pressure Turbine Vane

TL;DR: In this article, the authors established a benchmark data set of a generic high-pressure turbine vane generated by direct numerical simulation (DNS) to resolve fully the flow and investigated how turbulence affects the surface flow physics and heat transfer.
Journal ArticleDOI

HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

TL;DR: In this paper, a combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern.
Journal ArticleDOI

Trends in turbomachinery turbulence treatments

TL;DR: In this paper, a modular RANS turbulence modelling strategy is proposed and the need for improved measurements with well defined boundary conditions that have Reynolds stress and even spectral information, at Reynolds and Mach numbers that connect with typically powerful turbomachinery systems is identified.
Journal ArticleDOI

Effect of Simulated Combustor Temperature Nonuniformity on HP Vane and End Wall Heat Transfer: An Experimental and Computational Investigation

TL;DR: In this paper, the authors present experimental measurements and computational predictions of surface and end wall heat transfer for a high pressure (HP) nozzle guide vane operating as part of a full HP turbine stage in an annular rotating turbine facility, with and without inlet temperature distortion (hot streaks).
References
More filters
Book

Fundamentals of Heat and Mass Transfer

TL;DR: This paper introduced the physical effects underlying heat and mass transfer phenomena and developed methodologies for solving a variety of real-world problems, such as energy minimization, mass transfer, and energy maximization.
Journal ArticleDOI

Describing the Uncertainties in Experimental Results

TL;DR: The material presented in this paper covers the method of describing the uncertainties in an engineering experiment and the necessary background material, as well as a technique for numerically executing uncertainty analyses when computerized data interpretation is involved.
Journal ArticleDOI

The prediction of laminarization with a two-equation model of turbulence

TL;DR: In this article, the local turbulent viscosity is determined from the solution of transport equations for the turbulence kinetic energy and the energy dissipation rate, and the predicted hydrodynamic and heat-transfer development of the boundary layers is in close agreement with the measured behaviour.
Related Papers (5)